Echo HC-30ES Operator's Manual

SAFE OPERATION. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY. OPERATOR’S MANUAL HEDGE TRIMMER HC-30ES HC-30ESW ENGLISH GB ...

FAILURE TO WEAR PROPER PROTECTION CAN RESULT IN SERIOUS INJURY. READ AND UNDERSTAND THE RULES FOR SAFE OPERATION AND ALL INSTRUCTIONS IN THIS MANUAL. INTRODUCTION ECHO Hedge Trimmers, Models HC-30ES and HC- 30ESW are lightweight, high performance, petrol engined unit designed for hedge and shrub trimming. Do not use this unit for any purpose other than aforementioned. This Manual provides the information necessary for operation and maintenance. Specifications, descriptions and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without ...

before using this machine. • Follow all danger warnings in this manual. • Locate this safety decal on your unit. The complete unit illustration found in the “DESCRIPTION” section will help you locate them. Make sure the decal is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. Symbol form/shape Symbol description/application Symbol form/shape Symbol description/application Carefully read the operator’s manual Wear eyes, ears and head protection Carburettor adjustment -Idle speed Carburettor adju ...

Be sure you understand how to operate this unit properly before you use it. • If you have any questions or problems, please contact your ECHO dealer. • Be familiar with all the controls and the proper use of the machine. • Wear proper clothing to protect legs and other exposed parts of your body. • Wear non-skid sole shoes. Do not wear open-toed shoes or operate unit while bare footed. • Wear eye and hearing protection devices. • Use caution when handling fuel. Put the caps back tightly on both the fuel can and the trimmer fuel tank. Move at least 3 m from the refuelling ...

See your doctor • Dress properly! Do not wear loose clothing or jewellery, they can be caught in moving parts. Use of sturdy gloves, non-skid footwear, and safety glasses is recommended. • While operating the machine be always sure of a secure position. • Wear non-slip, heavy-duty work gloves to improve your grip on the trimmer handles. The gloves also help reduce the transmission of machine vibrations to your hands. PROTECTING OTHERS Spectators, children, fellow workers and animals must be warned to come no nearer than 10 m while the trimmer is in use. People working in the area near you should wear the same protectiv ...

obstacles and objects that could be thrown. • Do not force the blades and only move as quickly as the blades will allow. • Stop the engine and disconnect from ignition cable before: - cleaning or when clearing a blockage; checking, maintenance or working on the machine. • Handle fuel with care; it is highly flammable. Never add fuel to a machine with a running or hot engine. • Do not attempt to repair the machine unless you are qualified to do so. • Do not operate the machine with a damaged or excessively worn cutting device. • Always ensure all handles and guards are fitted when using th ...

before operation and keep for future reference to learn proper, safe operating techniques. 2. Spark plug 3. Carburettor - Device for mixing fuel and air in the correct proportions. 4. Silencer cover - Cover for the silencer to prevent operator contact with hot exhaust. 5. Starter handle - Pull handle to start the engine. (“ES” START) 6. Ignition switch - Device for allowing the engine to be started and stopped. 7. Brake lever - Brake to be used when starting the engine for enhanced safety. 8. Throttle trigger - Device activated by the operator’s finger, fo ...

FLAMMABLE. FOLLOW ALL RULES LISTED BELOW TO HELP PREVENT FIRE OR EXPLOSION WHICH MAY RESULT IN SEVERE INJURY OR DEATH. • AFTER REFUELLING, TIGHTEN FUEL CAP FIRMLY AND CHECK FOR LEAKAGE. IN CASE OF FUEL LEAKAGE, REPAIR BEFORE STARTING OPERATION SINCE THERE IS A DANGER OF FIRE. • Never smoke or allow flame or sparks near fuel. • Always fill the fuel tank outdoors. Never pour fuel indoors. • Always remove the fuel cap slowly to relieve any pressure build-up in the tank. • Never refuel the engine when it is hot or running. • Always use an approved, safe fuel container. • It ...

starting. • Always clear work area of debris before starting operation. • When pulling starter handle, use short pulls, 1/2 to 2/3 of rope length. • Do not allow the starter handle to snap back against the housing. • Always hold the unit firmly and make sure the cutting blades are free of obstructions before starting. Ignition switch START Throttle trigger SAFE STARTING TECHNIQUES 3. Place ignition switch in “START” position. 4. Push purge bulb until fuel is visible in clear fuel return line. 5. Move choke lever to CLOSE position. 6. Pull starter handle until first firing sound. ...

4. Move choke lever to OPEN position. 5. If tank is not empty, pull starter handle. 6. If fuel tank is empty, after refilling, push the purge bulb (until fuel is visible in clear fuel return line). Pull starter handle. NOTE If engine does not starting after four pulls, use cold starting procedure. Ignition switch START Throttle trigger Throttle trigger lockout STARTING WARM ENGINE Starter handle (“ES” START) Brake lever Releasing brake Brake lever Activating brake (After starting engine, release brake before commencing to use the unit.) 7. Put fingers on the right side of brake lever. 8. Return l ...

accelerate engine. 2. Tilt trimmer so cutting teeth are angled slightly toward the hedge or shrub and proceed to cut. • Keep both hands on handles while engine is running. • If blades jammed, stop engine, disconnect ignition cable and clean blades. • Do not overreach or stand on unstable surfaces. • If blades strike an obstruction or are prevented from functioning properly, stop engine and inspect blades for damage. • Do not operate the machine with a damaged or excessively worn cutting device. • To avoid damage, do not run at full throttle without load. • When two or more trimmers ...

16 • Cooling System Inspect/Clean 16 • Silencer Inspect/Tighten/Clean 16 • Gear Housing Grease 15 • (15 - 20h) Starter Inspect 13 • Blades Inspect/Clean/Lubricate 14, 15 • Fuel Leaks Inspect 14 • Screws, Bolts and Nuts Inspect/Tighten/Replace - • Fuel Line Inspect - • IMPORTANT Time intervals are maximum. Actual use and your experience will determine the frequency of required maintenance. Record dates of monthly and yearly inspections. ...

- does not start Fuel at carburettor Fuel at cylinder Spark at end of plug wire Spark at plug Dies or accelerates poorly No fuel at carburettor No fuel at cylinder Silencer wet with fuel No spark at end of plug wire No spark at plug Cause • Fuel filter clogged • Fuel line clogged • Carburettor • Carburettor • Fuel mixture is too rich • Ignition switch off • Electrical problem • Spark gap incorrect • Covered with carbon • Fouled with fuel • Spark plug defective • Internal engine problem • Air filter dirty • Fuel filter dirty • ...

Air filter CLEANING AIR FILTER (Before Each Use) CLEANING FUEL FILTER (Check Periodically) 1. Pick up fuel filter through fuel tank opening with a piece of steel wire or the like. 2. Clean filter in a suitable cleaner or replace it if necessary. 3. Reinstall the filter. CHECK SPARK PLUG (Check Periodically) 1. Check plug gap. Correct gap is 0.6 to 0.7 mm. 2. Inspect electrode for wear. 3. Inspect insulator for oil or other deposits. 4. Replace plug if needed and tighten to 15 - 17 N•m (150 to 170 kgf•cm). SERVICING 1. Close choke, remove wing bolt, cover and air filter. 2. Carefully brush dirt from filter or clean with a nonflammab ...

Remove gummy residue from blades with a 50 : 50 mixture of kerosene (paraffin) and machine oil. CAUTION If you experience any problems with sharpening the blade, we recommend that you take it to you ECHO dealer. NOTE Use a disk grinder, endless abrasive belt, or smooth flat file. SHARPENING BLADES (As Needed) NOTE Wear gloves to protect hands from sharp blades. Grease fitting LUBRICATING GEAR HOUSING (Every 15 - 20 Hours of Operation) 1. Clean dirt from grease fitting. 2. Carefully pump grease in fitting. DO NOT force grease. Too much pressure will force grease past seals and cause damage. Apply 1 - 2 pumps of gre ...

WARNING WHEN CARBURETTOR ADJUSTMENT IS COMPLETED, BLADES SHOULD NOT MOVE AT IDLE, OTHERWISE SERIOUS PERSONAL INJURY MAY RESULT. Every unit is test run at the factory and the carburettor is fine tuned for maximum performance. Before adjusting carburettor, clean or replace air filter, start engine and run several minutes to bring it to operating temperature. CAUTION When starting, idle speed adjuster should be adjusted not to move the blades. When there is some trouble with the carburettor, contact your dealer. 1. Idle Speed Adjustment. Start engine and turn idle speed adjustment screw c ...

(30 days or longer) without performing protective storage maintenance which includes the following: 1. Store unit in a dry, dust free place, out of the reach of children and other unauthorized persons. 2. Place the ignition switch in the STOP position. 3. Remove accumulation of grease, oil, dirt and debris from exterior of unit. 4. Perform all periodic lubrication and services that are required. 5. Tighten all the screws, bolts and nuts. 6. Drain the fuel tank completely and pull the recoil starter handle several times to remove fuel from the carburettor. 7. Remove the spark plug and pour 1/2 tab ...

kg 5.5 Unit, full tank kg 5.9 Volume : Fuel tank L 0.48 Cutting device : Type Dual action, Dual action, single sided blade double sided blade Length mm 752 Pitch mm 35 Height mm 23 Gear ratio and lubrication : 4.67 reduction and good quality lithium grease External Dimensions : length × width × height mm 1105 × 265 × 225 Engine : Type Air cooled Two stroke single cylinder Engine displacement mL (cm³) 21.2 Maximum shaft brake power (Referred to ISO 8893) kW 0.57 Engine speed at maximum engine power r/min 6500 Recommended maximum engine speed r/min 9400 Recommended engine idling speed r/min ...

The undersigned manufacturer: KIORITZ CORPORATION 7-2 SUEHIROCHO 1-CHOME OHME ; TOKYO 198-8711 JAPAN declares that the hereunder specified new unit: PORTABLE HEDGE TRIMMER Brand : ECHO Type : HC-30ES HC-30ESW complies with: *the requirements of Directive 98/37/EC (1998) (use of harmonized standard ISO 10517 (EN 774)) *the requirements of Directive 2004/108/EC (use of harmonized standards EN 50081-1, EN 50082-1, EN 55014 & EN 55022) *the requirements of Directive 2002/88/EC *the requirements of Directive 2000/14/EC Conformity assessment procedure followed ANNEX V HC-30ES HC-30ESW Measured sound power level dB(A) 101 ...

X753 224-660 3 GB 7-2 SUEHIROCHO 1-CHOME, OHME, TOKYO 198-8711, JAPAN PHONE: 81-428-32-6118. FAX: 81-428-32-6145. © 2006 ...