Fire Burglary Instruments XL-4 Owner's Manual

CODE [USER] Depress the CODE key followed by your user awess code. Assuming ihat the user is valid foruser definition the following displays will appear on LCD keypads; - Enter the user number to be entered or mdified. The user number must be entered as a three digit value, for example user #3 will be entered as 003. n Enter the desired four digit user code, The user code entered ( 0001 - 9999) must be unique and cannot be duplicated with another user code within the system. If an invalid code is entered, the keypad will beep four times and the keypad will repeat the ...

CONDITIONS In addition to individual zone alarms various condiions can be transmitted directly through the keypad. These renditions are initiated through the simultaneous depression of two keys, as shown below Reset - K a Keypad Condition m 2 * I R Keypad Condition 1 Condtions can be initiated directly through the keypad for various auxiliary condtions. These capa~lities will be defined by your installer for conditions such as PANIC, FIRE, or AUXILIARY. The keypad mn~tions are ative 24 hours a day, whether the system is armed or disarmed. For example if keypad emergency co ...

is another way to ARM your system wtile you remain in the location. The STAY mde will deactivate any interior protection zones which means that you will ba free to walk throughout your location without activating the alarm eystem. In order to enter the STAY mode, the system must be ready. (see previous description). STAY PROCEDURE: STAY [USER] Depress tha STAYkey followed byyour usercoda. LCD KEYPADS After a successful STAY arming the following display will appear lnaddition, the ARMED indicator will befit, lnthe STAy mode only the external or perimeter burglary protection ...

Early warning fire detetiion is best achieved by the installation of fire detesfion equipment the lo~fion as follows; Typical Smoke Detector Layout I. homes with mom than one sleeping am. a smoke detector should be provided to protect each erea. (Proposed) E ~lN,NG KITCHEN BEDROOM BEOROOM L,”, NG R“OM BEDROOM Smoke detector shall & located &tween the sleeping area a“d the rest of tk bus.. NOTES 1. Designates smoke detect.”. 2. Refer to N. F.P.A. *74 &Pe”tix B.1 ,1 thr” B.1 0. Preparation of an evacuation plan is of prime im~rtanw in fire prevention. Estabtis ...

Forced Arming is a method that will automatically bypass all faulted zones and ARM the system. NOTE:This cspabi~iy must be selected by your installer at the time of system installation. FORCED ARMING PROCEDURE; BYPASS [USER] BYPASS Depress the BYPASS key followed by your user code and the BYPASS key. If any of the zones cumenfly fauhed are not bypassable, then the command will not suaed, and a long infermpfed beep will follow. Following a eucceaaful forced arming the ARMED indicator will be fit and the ON :AWAYdisplay will appear on LCD keypads. NOTE This feature is NOT enabl ...

is another way to ARM your system wtile you remain in the location. The STAY mde will deactivate any interior protection zones which means that you will ba free to walk throughout your location without activating the alarm eystem. In order to enter the STAY mode, the system must be ready. (see previous description). STAY PROCEDURE: STAY [USER] Depress tha STAYkey followed byyour usercoda. LCD KEYPADS After a successful STAY arming the following display will appear lnaddition, the ARMED indicator will befit, lnthe STAy mode only the external or perimeter burglary protection ...

XL-4 Security Syetem. ARM/DISARM ARMING indicates that the burglary portion of your Secur~ Syetem has been turned on, DISARMED indicatee that the burgla~ potiion has been turned off. The FIRE protection and emergency pfions, if preeent in your system, remain active at all timee. BYPASS Allows certain burgla~ zones to be disarmed while the ramaindar of the system remains armed. For example, a bypaas would allow you to arm your system while a window is still open. CENTRAL STATION Your Security Syetem has buik in capabi~iy t ...