FirstWatt SIT-2 Manual 

Text of FirstWatt SIT-2 Manual 

Read Me First

I fully realize that many, if not all, owners will rush to hook up the amplifier without reading this operating manual. I don't blame you – I don't read them either. However, this amplifier is different in a number of ways, and if you only read this page you will probably save us both some time and trouble. Heat and Ventilation - This amplifier consumes 200 watts all the time and converts it into heat. Pick a location where the amplifie

I have been building power amplifiers for over forty years now, and at this late date I wasn't

expecting much in the way of surprises. In the past few years at First Watt I had been working with low power designs using some of the new power Jfet transistors from Lovoltech and SemiSouth which offered some performance improvements with simple circuits, so at least I felt like I was still making some incremental progress. The problem was, howev

Both amplifiers deliver about 10 watts output per channel. The SIT-1 is a monoblock drawing

about 200 watts, and the SIT-2 is a stereo amplifier also drawing about 200 watts. So what's the difference? First off, the SIT-1 gain device is surrounded by passive components, giving it a lower efficiency of around 5%. It is biased through 800 watts of power resistors mounted on the heat sink. The SIT-2 is biased by a constant current source created by another

The distortion performance of the SIT-2 into both 8 and 4 ohm loads is shown here:

In both curves we see a second harmonic character culminating in a very soft overload, which gives the amplifier more apparent power than its distortion ratings suggest. The SIT-1 and SIT-2 amplifiers can be driven in “direct mode” where the source components looks directly at the Gate of the SIT without other active components in between. This is desirable, but in this

To address this, There is the option of a simple P channel Jfet follower on the input which

raises the input impedance to 100,000 ohms and about 10 pF. Anything will drive this without problems. The distortion of the P channel Jfet is incredibly low, and doesn't alter the sound in any significant way, but it assures no impedance interation and a bandwidth to 500 Khz. The choice of input impedance is made on the jumper of the XLR female connector associat

This wide bandwidth is also reflected in the square wave response of the amplifier, here

shown at 20 Khz. The rise times are very fast, and there is no ringing or overshoot. Lastly, a plot of the distortion of the amplifier versus frequency shows a consistent character across the audio band: This consistency of performance over the audio band is an important element to the sonic character of the SIT-1 and SIT-2. The frequency and phase response is flat,

FirstWatt SIT-2 A Short Introduction to Static Induction Transistors

In the mid 1970's a special variety of Jfet invented in Japan called a Static Induction Transistor (SIT) found its way into the “Vfet” power amplifiers produced by Yamaha and Sony. These amplifiers were produced for several years and then discontinued, but are still highly regarded in the high end audio community. SIT devices have a unique characteristic which is of particular value for audio amplifi

FirstWatt SIT-2 The behavior of an ordinary Jfet or Mosfet is very similar:

As with the Pentode, the current flowing from Drain to Source in a Fet will flatten out as the voltage between those pins increases. By contrast, Here is a set of Triode (300B) curves:

In a Triode the current through the device depends not only on the control pins but also the

voltage across the device. In this sense the gain device acts in a manner similar to a resistor whose resistance value is controlled by the grid voltage. Similarly with the SIT device seen below: As with the comparisons between Pentodes and Fets, the curves have a similar

characteristic, but the scales have been altered by a factor of about 10, so that the voltages

are much lower and the current is much higher. Audiophiles often go to great expense to achieve as little as 5 watts of power using Triodes because of their specific sonic character. Unfortunately Triode performance is limited partly by the need to transform the high voltage / low current operation of the triode down to the low voltage / high current domain of l

Third - like Triodes, SITs have a soft overload characteristic. When over-driven on peaks they

present compressed, rounded waveforms instead of sharp clipping, the result being that they are more graceful under pressure. The entire effort revolves around simplicity and minimalism in circuit design. Certainly you can get good objective performance with multi-stage circuits and negative feedback. What we want is the sound that can be had from a single gai

Here is a picture of First Watt's SIT device:

Of course the audience for such an amplifier will only want to know about the sound. How does it compare with SETs from a subjective point of view? Having made a variety of these amplifiers at this point I can say that first off, they can be made to sound exquisitely in many of the systems that would enjoy the performance of a SET amplifier. These would be your high sensitivity loudspeakers featuring compress

FirstWatt SIT-2 thing that you notice when the amp is plugged in. The effect is a little intoxicating. ...the SIT

seems to bring a lot more control & detail to the speaker. The tube sweetness is present, yet the presentation is very clean. This is like a very nice low distortion SET. The SIT presents details, but with proper dynamic contrast. Details do not poke you in the eye, they just naturally unfold as part of the music. Do simple SIT amplifiers sound the same as

Summary of the nominal specifications:

Measured at 120 V AC and an 8 ohm load: Distortion @ 1 watt 0.7% Input Impedance 10 Kohm / 100 Kohm Gain 18 dB Output Impedance 4 ohms Output power 10 watts @ 5% THD, 1KHz Frequency response 4 Hz to 500 Khz (-3 dB) Noise 150 uV unweighted, 20-20 KHz Power consumption 200 watts Fuse 3AG slow blow type - 2.5 Amp for 120VAC 1.25 Amp for 240 VAC Weight 32 lbs Dimensions 17” W x 15” D x 5” H Colors: Available in Bla

FirstWatt Amplifier Owners Instructions: