Mark Levinson #52 Quick Start Manual

Text of Mark Levinson #52 Quick Start Manual

N052 Reference Preamplifier / Quick-Start Guide

English table of contents / About This Document table of contents About This Document 1 Installation Considerations 2 Unpacking, Placement and Ventilation, Power Requirements, Operating States Getting Started 4 Front-Panel Overview, Rear-Panel Overview, Remote Control Overview Quick Setup and Listen 11 Remote Control, Initial Connections Factory-Default Settings 16 Inputs, Aux Output, Volume Contro
N052 Reference Preamplifier / Quick-Start Guide Installation Considerations Unpacking When unpacking your N052: • Save all packing materials in case you need to ship your N052 in the future. • Inspect your N052 for signs of damage during shipment. If you discover damage, contact your authorized Mark Levinson® dealer for assistance in making appropriate claims. • Locate and remove the accessory box from the shipping carton. Make sure that all
N052 Reference Preamplifier / Quick-Start Guide English Installation Considerations Power Requirements The N052 has been designed for use with 100 – 240-volt, 50Hz/60Hz AC (alternating current), with a maximum current draw of 65W. It includes a detachable IEC power cable intended for use in the region where the N052 is sold. Connection to an AC voltage other than that for which the N052 is intended can create a safety and fire hazard and may damage
N052 Reference Preamplifier / Quick-Start Guide Getting Started Front-Panel Overview Getting Started Preamplifier chassis controls/indicators Preamplifier LED: illuminates fully when the N052 is On, illuminates dimly when the N052 is in either the Green or Power Save Standby mode, and flashes slowly in unison with the Standby LED when the N052 is in the Normal Standby mode. Preamplifier Logo: The Mark Levinson logo lights when the N052 is On, and turns
N052 Reference Preamplifier / Quick-Start Guide English Getting Started Controller chassis controls/indicators Select knob: Rotate this knob to select the desired input to send to the Main output connectors. The name and volume level of the selected input are indicated on the Front-Panel display. (Note: The Select knob will bypass any input for which the Input Name Setup menu parameter has been set to “Unused.”) IR receiver: The IR receiver receive
N052 Reference Preamplifier / Quick-Start Guide Rear-Panel Overview Getting Started Trigger Output Input ~ac mains 65W RS-232 IR Input Ethernet USB N052 Controller Right Channel DC Power Connector USB Port Ethernet Port Trigger Input Connector Trigger Output Connector Left Channel DC Power Connector AC Mains Connector Power Switch N052 Control Connector IR Input Connector RS-232 Port
N052 Reference Preamplifier / Quick-Start Guide English Controller chassis connectors DC Power connectors: These connectors provide DC power from the Controller chassis to the Preamplifier chassis. Use the two supplied multi-pin DC power cables to connect the Controller’s left-channel DC Power connector to the Preamplifier’s left-channel DC Power connector, and the Controller’s right-channel DC Power connector to the Preamplifier’s right-channe
N052 Reference Preamplifier / Quick-Start Guide Preamplifier chassis connectors Balanced input connectors: These connectors accept left- channel and right-channel balanced input signals from source components with balanced (male XLR) output connectors. Three balanced (female XLR) stereo connectors numbered 1, 2, and 3 are available. For best performance, use balanced connections whenever possible. Refer to the illustration below to ensure that the N052
N052 Reference Preamplifier / Quick-Start Guide English N052 Control connector: This multi-pin connector shares control information between the Controller chassis and the Preamplifier chassis. Use the supplied multi-pin N052 control cable to connect the Preamplifier’s N052 Control connector to the N052 Control connector on the Controller. DC Power connectors: These connectors receive DC power supplied by the Controller chassis. Use the two supplied m
N052 Reference Preamplifier / Quick-Start Guide Polarity Button Balance Button Setup Button IR Transmitter Standby Button Enter Button Display Button Mute Button Volume +/– Buttons Select +/– Buttons IR transmitter: This transmitter sends infrared signals to the IR receiver on the Controller’s front-panel display Standby button: Press this button to put the N052 into and out of the Standby mode. The Standby LED on the Controller front panel illu
N052 Reference Preamplifier / Quick-Start Guide English Remote Control Battery Replacement Your N052 remote control comes with two AAA alkaline batteries already installed. If the remote control seems to operate intermittently, or if the remote control’s IR transmitter LED illuminates dimly or not at all when a button is pressed, replace both batteries with new ones. We recommend that you use alkaline batteries, which do not leak and last longer tha
N052 Reference Preamplifier / Quick-Start Guide Quick Setup and Listen Initial Connections CAUTION: Before making connections, make sure the N052 and all associated components are powered off and disconnected from electrical outlets. 1. Using one of the supplied DC power cables, connect the Controller’s left-channel DC Power connector to the Preamplifier’s left-channel DC Power connector. Connect the right-channel DC Power connectors using the oth
N052 Reference Preamplifier / Quick-Start Guide English 3. Connect a source component to the desired N052 Preamplifier input connectors. • Use the N052 Balanced input connectors numbered 1, 2, or 3 if the source component offers balanced output connectors. • Use the N052 Unbalanced input connectors numbered 4, 5, 6 or 7 if the source component does not offer balanced output connectors. • Use the N052 Phono input connectors to connect to a tur
N052 Reference Preamplifier / Quick-Start Guide 4. Connect the desired N052 Preamplifier Main output connectors to the associated power amplifier input connectors. • Use the N052 balanced Main output connectors if the associated power amplifier offers balanced input connectors. • Use the N052 unbalanced Main output connectors if the associated power amplifier does not offer balanced input connectors. Quick Setup and Listen outputs inputs single
N052 Reference Preamplifier / Quick-Start Guide English 5. Connect the supplied power cable to the Controller and into an electrical outlet. 6. Power the N052 and all associated components on. NOTE: Power amplifiers should be powered on last. 7. Rotate the N052 select knob or press the Select +/– buttons on the remote to select the N052 input that corresponds to the input connectors to which you connected the source component. • The N052’s fron
N052 Reference Preamplifier / Quick-Start Guide Factory-Default Settings The following are the factory-default settings for the N052’s Setup menu. For information about all Setup menu settings see the N052 User Guide, which can be found on the supplied USB memory stick. Inputs The following setting defaults apply to all Inputs: Name: Input X (the selected input connector number) Gain: 0dB Volume Offset: 0.0dB SSP: Off (Note: SSP is not available for

Mark Levinson Amplifier Owners Instructions: