Electrolux FI259/2TA++ Operation & User’s Manual

Share more of our thinking at www.electrolux.com CONTENTS Safety information 2 Operation 4 First use 4 Daily use 4 Helpful hints and tips 6 Care and cleaning 6 What to do if… 8 Technical data 10 Installation 10 Environmental concerns 14 Subject to change without notice SAFETY INFORMATION In the interest of your safety and to ensure the correct use, before installing and first us- ing the appliance, read this user m ...

circuit, fire and/or electric shock. Warning! Any electrical component (power cord, plug, compressor) must be replaced by a certified service agent or qualified service personnel. 1. Power cord must not be lengthened. 2. Make sure that the power plug is not squashed or damaged by the back of the appliance. A squashed or dam- aged power plug may overheat and cause a fire. 3. Make sure that you can come to the mains plug ...

icing of the appliance should be carried out by a qualified electrician or compe- tent person. • This product must be serviced by an au- thorized Service Centre, and only genu- ine spare parts must be used. Environment Protection This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insula- tion materials. The appliance shall not be discarde ...

When first starting-up or after a period out of use, before putting the products in the compartment let the appliance run at least 2 hours on the higher settings. Important! In the event of accidental defrosting, for example due to a power failure, if the power has been off for longer than the value shown in the technical characteristics chart under "rising time", the defrosted food must be consumed quickly or cooked immediately and ...

Hints for energy saving • Do not open the door frequently or leave it open longer than absolutely necessary. • If the ambient temperature is high and the Temperature Regulator is set to low temperature and the appliance is fully loa- ded, the compressor may run continuous- ly, causing frost or ice on the evaporator. If this happens, set the Temperature Reg- ulator toward warmer settings to allow au- tomatic defrosting and so a sa ...

out by authorized technicians. Periodic cleaning The equipment has to be cleaned regularly: • clean the inside and accessories with luke- warm water and some neutral soap. • regularly check the door seals and wipe clean to ensure they are clean and free from debris. • rinse and dry thoroughly. Important! Do not pull, move or damage any pipes and/or cables inside the cabinet. Never use detergents, abrasive powde ...

When the appliance is not in use for long pe- riods, take the following precautions: • disconnect the appliance from elec- tricity supply • remove all food • defrost 5)and clean the appliance and all accessories • leave the door/doors ajar to prevent un- pleasant smells. If the cabinet will be kept on, ask some- body to check it once in a while to prevent the food inside from spoiling in case of a power failure. WHAT TO DO ...

appliance is too high. The temperature regulator is not set correctly. Set a lower temperature. The door is not closed correctly. Refer to "Closing the door". The product temperature is too high. Let the product temperature de- crease to room temperature be- fore storage. Many products are stored at the same time. Store less products at the same time. The temperature in the re- frigerator is too high. ...

Height 1446 mm Width 560 mm Depth 550 mm Rising Time 20 h The technical information are situated in the rating plate on the internal left side of the ap- pliance and in the energy label. INSTALLATION Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance. Positioning Install this appliance at a location where the ambient temperature corresponds to ...

1. Tighten the lower pin. 2. Install the lower door. 3. Tighten the middle hinge. 4. Install the spacer. 5. Install the upper door. 6. Tighten the upper pin. Ventilation requirements The airflow behind the appliance must be sufficient. 50-min. cm2200 min. cm2200 Installing the appliance Caution! Make sure that the mains cable can move freely. Do these steps. 1. Install the appliance in the niche. Push the appliance in the direction of ...

furniture is correct. Open the door. Put the lower hinge cov- er in position. 44mm 4mm 3. Attach the appliance to the niche with 4 screws. I 4. Push the sealing strip between the ap- pliance and the adjacent cabinet. 5. Remove the correct part from the hinge cover (E). Make sure to remove the part DX, in the case of right hinge, SX in op- posite case. 6. Attach the covers (C, D) to the lugs and the hinge holes. Install ...

the kitchen furniture. ca. 50 mm ca. 50 mm 21 mm 90° 90° 21 mm 9. Push the part Hc on the part Ha. Ha Hc 10. Open the appliance door and the kitch- en furniture door at an angle of 90°. Insert the small square (Hb) into guide (Ha). Put together the appliance door and the furniture door and mark the holes. Ha Hb 8 mm 11. Remove the brackets and mark a dis- tance of 8 mm from the outer edge of the do ...

Hb Hd 14. To open the doors do these steps. Use the sliding system previously illus- trated or open one of the two doors by fitting the small handle supplied as an acces- sory. Do a final check to make sure that: • All screws are tightened. • The magnetic sealing strip is attached tightly to the cabinet. Important! If the ambient temperature is low (for example, in the Winter), the size of the gasket decreases. ...