Air Live WL-5470AP Quick Setup Manual

List of Languages 108 120 ...

We, Manufacturer/Importer OvisLink Corp. 5F., NO.6, Lane 130, Min-Chuan Rd., Hsin-Tien City, Taipei County, Taiwan Declare that the product Wireless AP AirLive WL-5470AP is in conformity with In accordance with 89/336 EEC-EMC Directive and 1999/5 EC-R & TTE Directive Clause Description ■ EN 300 328 v1.7.1 (2006-10) Electromagnetic compatibility and Radio spectrum Matters (ERM); wideband transmission equ ...

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferences when the equipment is operating in a commercial area. This equipment generates uses and may radiate radio frequency energy, and if not installed in accordance with the user guide, may cause in ...

use. „„ TX output power is limited to 20dBm (EU) 23dBm (FCC) , up to 25dBm (South America) „„ The AP mode’s default IP address is 192.168.100.252 „„ The default Subnet Mask is 255.255.255.0 „„ The default SSID is airlive „„ The default Channel is 11 „„ The default login username is admin and no nee ...

after boot successfully, the light turns Green. WAN Green Turns solid yellow when connect with 10Mbps / Green with 100Mbps speed Ethernet client. Receiving/ Sending data Wireless Green Turns solid green after booting is successful Receiving/ Sending data LAN 1~LAN4 Green Turns solid yellow when connect with 10Mbps ...

2. Screw-in the antenna (clockwise) into the Antenna connector 3. Connect the power and LAN cable to the back 4. Use your wireless card to do a site survey, the default SSID is airlive and Channel is 13 5. If you need to change AP’s configuration, please follow the procedure below: „ The AP’s default IP address is 192.168.100.252. Please make sure yo ...

Client Mode English Device B: WISP Outdoor AP Network Type: Infrastructure Device A: Mode: Client mode Please make sure both A and B are set to the same ESSID and channel. ...

MAC Address: Device A’s AP MAC Address Device A: Mode: Bridge mode MAC Address: Device B’s AP MAC Address Please make sure both A and B are set to the same channel. WDS Repeater Mode Setup WDS Repeater Mode English Device A: Mode: WDS Repeater MAC Address: Device B’s AP MAC Address Device B: WDS Wireless AP/ Router MAC Address: Device A’s AP MAC Address ...

channel number. 2. Add other’s AP MAC Address(BSSID) that the repeater want to connect. (Please make sure remote wireless AP/Router Support WDS function) 3. Setup wireless security function: Wireless Client: WDS Repeater Æ Security WDS Security: WDS Repeater Æ WDS Security WDS Repeater and Wireless Client use different authentication and encryption for wireless connection. F ...

Universal Repeater Mode Device B: Wireless Router Device A: Mode: Universal Repeater Universal Repeater doesn’t require the remote device to have WDS function. 1. Please make sure both A and B are set to the same chann number. 2. Type the other’s AP/Router’s SSID in the “SSID of Extended Interface” field that the repeater want to connect. ! Note: The device SSID and the SSID of Extended Interface can ...

Device B: WISP Outdoor AP Device A: Mode: WISP (Client Router) WISP (Client Router) Mode 1. Please click the “Site Survey” button to search and connect the WISP Outdoor AP device. 2. IN WISP mode, please click the WAN Port Setup button for WAN port configuration. Choose the WAN Access Type and type some information in other field. For detail, please refer to the user manual. English ...

Please enter “Device B” SSID in the “SSID” field for the WISP connection, and enter “Device A” SSID in the “SSID of Extended Interface” field for the PC side connection. In this mode,WL-5470AP behaves virtually the same as in WISP mode, but the AP can also send wireless signal to the Wireless LAN side. The output-power is divided between 2 wireless sides, and proper antenna installation can ...

1 Please connect your PC’s Ethernet Port to LAN port in the back side of the AP. 2 Connect the WAN to the ADSL modem or Cable Modem. 3 In the Web configuration UI, choose the “Gateway” mode of the Mode Setting and click the setup button. English ...

configuration: 7. You can choose DHCP client, PPPOE, PPTP,L2TP or static IP type for each related configuration. For details , please refer to User’s Manual. In this mode, you can act this device as a broadband router also as a Wireless AP let Wireless Client to access to the internet. English ...

cyfrowych należących do Klasy B (Class B), według części 15 Reguł FCC. Ograniczenia te zostały zaprojektowane w celu zapewnienia uzasadnionej ochrony przed szkodliwymi interferencjami, które mogą powstać podczas użytkowania produktu w środowisku miejskim. Urządzenie wytwarza, używa i może promieni ...

gdy ustawiony jest tryb pracy gateway (bramki sieciowej). „„ Moc wyjściowa TX została ograniczona do 20 dBm (EU) 23 dBm (FCC) i do 25 dBm (Ameryka Południowa) „„ Domyślnie adres IP to 192.168.100.252 „„ Domyślnie maska podsieci to 255.255.255.0 „„ Domyślnie SSID to airlive „„ Domyślnie kanał 11 ...

Mruga Power Zielony Świeci na żółto podczas uruchamiania się urządzenia, po prawidłowym starcie zaczyna świecić na zielono WAN Zielony Świeci na żółto podczas połączenia 10 Mb/s, a na zielono przy połączeniu z prędkością 100 Mb/s Wysyłanie lub odbieranie danych Wireless Zielony Zaczyna świecić na zielono po prawidłowym uruchomie ...

2. Przykręć dołączoną do urządzenia antenkę do gniazda antenowego. 3. Podłącz zasilanie i kable Ethernet do portów LAN/LAN2. 4. Uruchom na komputerze z aktywną kartą radiową funkcję wyszukiwania sieci bezprzewodowych. Domyślnie SSID to airlive, kanał 11 5. W celu modyfikacji domyślnych ustale ...

Należy upewnić się, że zarówno urządzenie A, jak i B ustawione są na prace w tym samym ESSID i kanale. Polski Tryb Client Urządzenie B: WISP Outdoor AP Typ sieci: Infrastructure Urządzenie A: Tryb: Client ...