Cissell WE176 Installation Instructions Manual

3 2 Technical data and dimensions....................................................... 4 Technical data ................................................................................ 4 Dimensions ..................................................................................... 5 3 Installation and connection ................................ ...

Read the installation and instruction manual carefully before connecting the machine. It is recommended that the machine be installed by qualified technicians. The machine should be installed according to the installation instructions. (See chapter 4) The machine should be grounded according to the instructions in order to eliminate the risk of electrocution. Do not expose the machine to high humidity or extreme high or low ...

Technical data WE 176 WE 234 Capacity (dry weight) 1/11 16 kg 21,3 kg 1/10 17,6 kg 23,4 kg 1/9 16,1 kg 26 kg Cylinder Diameter 750 mm 750 mm Depth 399 mm. 530 mm Volume 176 Lit. 234 Lit. Cabinet Height 1505 mm 1505 mm Width 900 mm 900 mm Depth 800 mm 930 mm Front loading Diameter door opening 395 mm 395 mm Door height 510 mm 510 mm To center 750 mm 750 mm Speed Wash 45 rpm Spin 425 rpm G-force Spin 76 Motor(3 phase) Wash 1 ...

B. Warm water connection 3/4" C. Soft water connection 3/4" D. Electrical connection E. Electrical connection clamps F. Water drain G. Steam connection H. Ventilation soap dispenser S S S S S S S S Downloaded from www.Manualslib.com manuals search engine ...

B. Warm water connection 3/4" C. Soft water connection 3/4" D. Electrical connection E. Electrical connection clamps F. Water drain G. Steam connection H. Ventilation soap dispenser WE234 Downloaded from www.Manualslib.com manuals search engine ...

solid ground). The anchoring is to be done on the provided places (A) in the base. (See Dimensions 2) The machine must be placed entirely level. For easy maintenance it is recom- mended to keep a minimal distance of 600 mm between the wall and the back of the machine. If several machines are placed next to each another, there should be a minimal d ...

Connect the power cable to the connectors. 220V 3AC 220V 3 phase (3AC) should be connected to the connectors “L1,L2,L3”. The green/yellow grounding clamp has to be connected to the grounding wire “PE”. 380 V 3AC + N 380 V 3 phase (3AC + N) has to be connected to the connectors “L1,L2,L3”, the blue neutral to the “N” connector. The green/yellow grounding clamp has ...

Electrical connection of the liquid soap pumps On machines equipped with a liquid soap connection, connect the wires directly on the print board next to the ground wire connection (option). Connect as indicated on the wiring diagram. The two connectors on the right give a tension of 220V ~ (max. 4A) which can be applied to drive 220V ~ soap pumps. If more than 4A is required, an external tension will have to be used. 6 c ...

panel for coinmachines (option) At the backside above the main connectors, you find a printboard, to which the central operating panel for coinmachines can be connected. The right connectors form a potential free output contact as a result of which the operating panel detects when the machine is activated or not. The left connectors receive the signal, by means of which a machine is chosen through the operating pane ...

1. Steam pipe 2. Steam cut-off valve 3/8" 3. Pipe coupling 3/8" 4. Steam filter 3/8" 5. Magnetic steam valve 3/8" 6. Curve MF 3/8" 7. Steam hose with appropriate pipe coupling 3/8" The manufacturer is not responsible for damage or accidents caused by not following the installation instructions! Added parts for steam heating with heat exchanger 3. Double pipe coupling 1/2" 9. Condensation ac ...

Sort the linen according to the type and required temperature of the linen. Empty all pockets of the garments so that no garments can be damaged and no left articles can cause damage to the machine. Turn sleeves of shirts, blouses inside out. It is recommended to mix small and large items to enhance the drop of the linen during the wash cycle and hence improve the wash quality. Wash loads of below 80% o ...

The door is sealed and the cycle-LED lights up. During the first 2 minutes after starting, the program number is blinking and you can change the program in case of a possibly wrong selection. To do so, select another program with the SELECT button (P). This new program will start immediately. Start the machine Display information The left display will indicate the tem ...

with the right spin-LED (final spin). - Functioning of the spin-LED’s during final spin: LED drain/distribution low spin high spin coast tumble Interm. spin blinking rapidly continuously slowly continuously off Final spin continuously continuously slowly continuously rapidly - Functioning of the spin-LED’s during gentle-final spin: LED drain/distribution low ...

During the wash cycle: The wash time is stopped. The temperature, water level and wash action remain the same as programmed. During the wash cycle, this function remains active until the START button (S) is pressed again. During intermediate spin : The intermediate spin normally lasts 1 minute. By activating function F1, the machine will spin for nine minutes unless the START button (S) is pressed earlier. During final spin : ...

By selecting F3, the wash action time and pause time will be reversed; unless the wash action time was programmed to be shorter than the pause time. Example: 12 sec. action/3 sec. pause becomes: 3 sec. action/12 sec. pause 6 sec. action/9 sec. pause remains: 6 sec. action/9 sec. pause This function does not influence the cycle time - the program continues normally - and remains active until the STAR ...

At the end of a program, while the door is being released, the left display shows End; and the Start-LED is switched off. After that only the right display will continue to show the program number. This is the end of the program. Premature ending of the program By pressing the START-button (S) during the program, the Start-LED is switched off and the water is drained from the machine. As long as the water has not reached the safety le ...

Before starting a program it is possible to preprogram a time stop in every program segment. This function permits special additional functions like adding bleach or extra detergent to the wash bath. Programming: After selecting the program, press the ECO-button (E) and keep it depressed. Now push the START-button (S) simultaneously and release same. Only now release the ECO-button (E). The left display now s ...

It is possible to run 2 programs automatically in sequence. This can be handy to perform very special functions (like waterproofing outerwear) and add these to the wash program. Programming: First select the program which will be run last. Now, press the START-button (S) and keep it depressed for at least 5 seconds. The left display now shows “Add”. Now select the program which will be run first. The right display now shows both ...

tub and that the cylinder has come to a complete stop. Important: Remote stop function By means of this function, no cycles can be selected anymore during a certain period of time (e.g. between 10 p.m. and 7 a.m.). This time is determined by an extern timer. As soon as the last cycle is finished, “ OFF “ (blinking) appears on the left display as long as this functio ...