Radio Shack Trunk Mount Owner's Manual

Text of Radio Shack Trunk Mount Owner's Manual

Cat. No. 12-1976

OWNER’S MANUAL Please read before using this equipment. 4 × 25 Watt Trunk Mount Amplifier 4-Channel 100-Watt 12-1976.fm Page 1 Tuesday, July 13, 1999 10:01 AM

Radio Shack Trunk Mount © 1995 Tandy Corporation.

All Rights Reserved. Optimus and Radio Shack are registered trademarks used by Tandy Corporation. Your Optimus 4 × 25 Watt Trunk Mount Amplifier is designed to pro- duce a total of 100 watts to give add- ed punch and power to your vehicle’s existing stereo system. The amplifier produces up to 25 watts per channel of clean, powerful sound at all audio frequencies with minimum distortion. And, you can connect line-lev

Preparation ..................................................................................................... 4

Choosing a Mounting Location .................................................................. 4 Before You Begin the Installation ............................................................... 4 Connecting Ground and Primary/Switched Power .................................... 5 Connecting Your Autosound System ..............

CHOOSING A MOUNTING LOCATION

The ideal location for mounting the amplifier is in your vehicle’s trunk. Wherever you decide to mount it, choose a mounting location that: • Does not interfere with the vehicle’s operation • Lets you drill mounting holes without damaging other vehicle components • Allows enough space around the cooling fins for proper airflow and cooling Warning: The amplifier gets very hot while it is on. Do not touch

• To prevent damage to your amplifier or autosound system, you must first

connect the ground, primary, and switched power wires (as described in “Connecting Ground and Primary/Switched Power” before you connect the speakers to the amplifier. Make the connections only in the order shown. Damage to the amplifier is possible if you connect any wire incorrectly. • Turn on the power to test the connections before you permanently mount the am

Note: After you complete the connections and reconnect the battery wire,

you will need to reset all clock/timer/memory devices in your vehicle. 2. Connect the supplied dark blue/white wire’s end to the amplifier’s REM (remote power) terminal. 3. Securely connect the supplied dark blue/white wire’s male quick disconnect plug to your autosound system’s switched power lead. This connection turns your amplifier on or off when you turn your autosound

CONNECTING YOUR AUTOSOUND SYSTEM

Low Level Input Connections You can connect your autosound system’s low-level phono output jacks to the amplifier’s LOW INPUT phono jacks. Note: For a cleaner, less noisy signal transfer between your autosound system and the amplifier, the amplifier’s LOW INPUT phono jacks are gold-plated. For the best results, use shielded audio cables, such as Cat. No. 42-2368 (not supplied). If your autosound system has only two

If your autosound system has four phono outputs but you are using only two

speakers (front or rear), connect only the corresponding autosound sys- tem’s output jacks to the amplifier using audio cables as follows: • front-left to FRONT L and front-right to FRONT R, or • rear-left to REAR L and rear-right to REAR R 12-1976.fm Page 8 Tuesday, July 13, 1999 10:01 AM

Radio Shack Trunk Mount If your autosound system has only two phono output jacks (left and right)

and you are using four speakers, first connect the single phono plug end of a Y-adapter shielded audio cable to each autosound system output jack. Then: • Connect the other two ends of the left Y-adapter to the amplifier’s corre- sponding FRONT L and REAR L phono jacks • Connect the other two ends of the right Y-adapter to the amplifier’s corre- sponding FRONT R and REAR R
If your autosound system has only two phono output jacks (left and right) and you are using only two speakers, simply connect them to the amplifier’s corresponding FRONT L and FRONT R, or REAR L and REAR R phono jacks. High-Level Input Connections If your stereo system has only speaker outputs, you can connect them to the am- plifier’s rear HIGH INPUT and front HIGH INPUT sockets using the floating ground connection or the common ground connection m

If your autosound system has four speaker outputs and you are going to use four

speakers: Floating Ground Connection Common Ground Connection 12-1976.fm Page 11 Tuesday, July 13, 1999 10:01 AM

If your autosound system has only two speaker outputs and you are going to use

four speakers: Floating Ground Connection Common Ground Connection 12-1976.fm Page 12 Tuesday, July 13, 1999 10:01 AM

CONNECTING THE SPEAKERS

With the speakers placed in their approximate locations, run one speaker wire from each speaker to the amplifier. We recommend you use 16- or 18-gauge marked or color-coded wires to help you correctly connect the speakers to your amplifier. For the maximum bass response and the best overall performance, keep your speakers properly phased (connect + to + and - to -). Caution: Do not connect the speakers’ negative (-) terminal wi

Connecting Four Speakers

1. Connect one end of a speaker wire’s marked conductor to the amplifier’s FL+ (front-left positive) terminal. 2. Connect one end of the speaker wire’s unmarked conductor to the ampli- fier’s FL- (front-left negative) terminal. 3. Repeat Steps 1 and 2 to connect a speaker wire to the amplifier’s FR (front- right) terminals. 4. Repeat Steps 1 - 3 to connect speaker wires to the amplifier’s RL (rear-left) and RR (rear-

Connecting Two Speakers

If you are connecting only two speakers, you can connect them to the amplifier’s front (FL and FR) or rear (RL and RR) speaker terminals. 1. Connect one end of a speaker wire’s marked conductor to the amplifier’s FL+ (front-left positive) or RL + (rear-left positive) terminal. 2. Connect the end of the speaker wire’s unmarked conductor to the ampli- fier’s FL− (front-left negative) or RL − (rear-left negative) termi

TESTING THE CONNECTIONS

Before you permanently mount the amplifier, temporarily reconnect your vehicle battery’s negative (-) cable, turn your vehicle’s ignition to ON or ACC, then test the connections. The amplifier is properly connected to the autosound system and speakers if you can verify that the amplifier and the autosound system turn on properly and the speakers’ sound is clear and unmuffled. If you cannot quickly verify that all components

Radio Shack Amplifier Owners Instructions: