Windsor 1.005-297.0 Operator's Manual

Operator’s Manual Floor Machine MODELS: 1.005-297.0

Machine Data Label All Radiant equipment has been carefully tested and inspected at our USA factory. Radiant machines are guaranteed for one year from the date of original purchase against defects or workmanship made during manufacture. Within the guarantee period we undertake at our discretion, to repair or replace any part found to be defective, free of charge to the purchaser with subject to the following conditions: Claims made under the terms of the guarantee must be supported by the original invoice issued at the time of sale along with the machine serial number. For claims under this guarantee contact the supplier from whom you’ve purchased the product who will arrange the appropriate action. Do not initially return the product as this could lead to transit damage. Neither Radiant nor its distributors will be held responsible for any incidental or consequential loss. This guarantee does not cover: Periodic maintenance, repair, or replacement of parts due to normal wear and tear. Damage caused by accident, misuse or neglect, fire, or the fitting of other than genuine Radiant parts. Defects in other than genuine Radiant parts, repairs, modifications or adjustments made by other than a Radiant service engineer or authorized service dealer. Costs and risks of transport relating directly or indirectly to the guarantee of this product. Consumable items such as brushes, drivers, velcro discs, gliders, pads, and so forth. Radiant has a policy of continual product development and we reserve the right to alter specifications without prior notice.

Machine Data Label. . . . . . . . . . . . . . . . . . . . . . . . . .1 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . .2 How To Use This Manual . . . . . . . . . . . . . . . . . . . . .3 Safety Hazard Intensity Level . . . . . . . . . . . . . . . . . . . . . . .5 Grounding Instructions . . . . . . . . . . . . . . . . . . . . . . .6 Operations Unpacking and Initial Operations . . . . . . . . . . . . . . .8 Pre-Run Inspection . . . . . . . . . . . . . . . . . . . . . . . . . .8 Process of Cleaning . . . . . . . . . . . . . . . . . . . . . . . . .9 End of the Application. . . . . . . . . . . . . . . . . . . . . . . .9 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Lifting and Carrying. . . . . . . . . . . . . . . . . . . . . . . . .10 Weight Kit Installation . . . . . . . . . . . . . . . . . . . . . . .10 Brush Installation . . . . . . . . . . . . . . . . . . . . . . . . . .11 Attaching and Removing the Driver Plates . . . . . . .11 Accessories And Applications. . . . . . . . . . . . . . . . .12 Standard Driver Plate . . . . . . . . . . . . . . . . . . . . . . .12 Carpet Pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Chemical Free Stripping Pad . . . . . . . . . . . . . . . . .13 Scrub Brush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Concrete Brush. . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Superzorb Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Carpet Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Cleaning Hard Floors . . . . . . . . . . . . . . . . . . . . . . .15 Maintenance Cleaning the Machine . . . . . . . . . . . . . . . . . . . . . . .16 Changing The Driver Grip Face . . . . . . . . . . . . . . .16 Parts Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Frame, Wheels, & Pump. . . . . . . . . . . . . . . . . . . . 25 Spray Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 8.638-856.0 Manual Operators - Radiant Orbital Scrubber

This manual contains the following sections: • How to Use This Manual • Safety • Operations • Maintenance • Parts List The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authorized dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the MACHINE DATA box which is filled out during the installation of your machine. The MACHINE DATA box is located on the inside of the front cover of this manual. The model and serial number of your machine is located on the back of the machine. The SAFETY section contains important information regarding hazardous or unsafe practices of the machine. Levels of hazards are identified that could result in product damage, personal injury, or severe injury resulting in death. The OPERATIONS section is to familiarize the operator with the operation and function of the machine. The MAINTENANCE section contains preventive main- tenance to keep the machine and its components in good working condition. They are listed in this general order: • Cleaning the Machine • Changing The Driver Grip Face The PARTS LIST section contains assembled parts illustrations and corresponding parts list. The parts lists include a number of columns of information: • REF – column refers to the reference number on the parts illustration. • PART NO. – column lists the part number for the part. • QTY – column lists the quantity of the part used in that area of the machine. • DESCRIPTION – column is a brief description of the part. • NOTES – column for information not noted by the other columns. NOTE: If a service or option kit is installed on your machine, be sure to keep the KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts. NOTE: The manual part number is located on the lower right corner of the front cover. Model: Date of Purchase: Serial Number: Dealer: Address: Phone Number: Sales Representative: 8.638-856.0 Manual Operators - Radiant Orbital Scrubber

When using this machine, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. WARNING To reduce the risk of fire, electric shock, or injury: • Use only indoors. Do not use outdoors or expose to rain. • Use only as described in this manual. Use only manufacturers recommended components and • attachments. • If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into • water, return it to an authorized service center. • Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce • airflow. • Machine near flammable fluids, dust or vapors. • This machine is suitable for commercial use such as: in hotels, schools, hospitals, factories, shops, and • offices for more than normal housekeeping purposes. • Maintenance and repairs must be done by qualified personnel. • During operation, use caution around other persons, especially children. • The machine shall only be operated by instructed and authorized persons. • When leaving unattended, unplug the machine. • Do not handle the plug or machine with wet hands. • Do not unplug machine by pulling on cord. To unplug, grasp the plug and not the cord. • Do not use with damaged cord or plug. Follow all instructions in this manual concerning grounding the • machine. • Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp • edges or corners. • Do not pull/run machine over cord. Keep cord away from heated surfaces. • Connect to a properly grounded outlet. See Grounding Instructions. • If the supply cord is damaged it must be replaced by an authorized service agent. • Unplug before cleaning or servicing. • Operational hazard may occur when running the machine over the supply cord. • This appliance has been designed for use with pads specified by the manufacturer. The fitting of other • pads may affect its safety. • This machine is for dry use only and shall not be used or stored outdoors in wet conditions • Moving Parts - To reduce the risk of injury, unplug before servicing. READ AND SAVE THESE INSTRUCTIONS 8.638-856.0 Manual Operators - Radiant Orbital Scrubber

Hazard Intensity Level There are three levels of hazard intensity identified by signal words -WARNING, CAUTION, and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING WARNING - Hazards or unsafe practices CAN result in severe personal injury or death. CAUTION CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage. FOR SAFETY: To Identify actions which must be followed for safe operation of equipment. Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating condition. The following is information that signals some potentially dangerous conditions to the operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the machine. Please take the necessary steps to train the machine operating personnel. FOR SAFETY: DO NOT OPERATE MACHINE: • Unless trained and authorized. • Unless Operation Guide is read and understood. • In flammable or explosive areas. • In areas with possible falling objects. WHEN SERVICING MACHINE: Avoid moving parts. Do not wear loose clothing, jackets, shirts, or sleeves when working on the machine. Use only manufacturer approved replacement parts. 8.638-856.0 Manual Operators - Radiant Orbital Scrubber

USE ONLY ELECTRICAL: US/(EU) This machine operates on a 14/(7) amp nominal 120/ (230)V, 60/(50) hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors. Grounding Instructions This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord that has an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordi- nances. This appliance is for use on a nominal 120/(230) volt circuit, and has a grounded plug that looks like the plug in “Fig. A”. A temporary adapter that looks like the adapter in “Fig . C” may be used to connect this plug to a 2-pole receptacle as shown in “Fig. B”, if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet (Fig. A) can be installed by a qualified electrician. The green colored rigid ear, lug, or similar that extends from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw. WARNING Improper connection of the equipment-grounding conductor can result in electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Safety Label Location These drawings indicate the location of safety labels on the Machine. If at any time the labels become illegible, contact your authorized representative for prompt replacement. 8.638-856.0 Manual Operators - Radiant Orbital Scrubber USING AN ADAPTOR GROUNDING CONNECTION Note: Adaptors are not allowed in Canada. Outlet Tab for Grounding Outlet Box FIGURE C Grounded FIGURE A Adaptor Screw FIGURE B Adaptor Metal Screw Grounded Grounding Pin

RPM 1725 (60Hz)/1400 (50Hz) Base Diameter 17.38“/ 43 cm Orbital Diameter 3/8” (9.5mm) Machine Weight 95 Lbs./ 43 kg Height 48.8” (123.9 cm) Length 28.19” (71.6cm) Wheels 10”/25 cm Diameter, Resistant To Chemicals 8.638-856.0 Manual Operators - Radiant Orbital Scrubber 17.0 17.38 15.00 28.19 13.76 48.8 RIGHT SIDE VIEW

Open the shipping box on both sides, remove the packaging material and roll the machine out of the box. Fill the tank with water. You can add a cleaning solution of your choice in a prescribed mixing ratio. Pre-Run Inspection Before each use, inspect the accessory such as the pad driver for cracks, tears, or excess wear. If the machine or accessory is dropped, inspect for damage to install an undamaged accessory. Repair the damaged machine before the next applica- tion. Tilt the head back and place the foot of the bumper on the ground.Choose a pad for the appropriate applica- tion. Center the pad on the driver plate. Position the handle in a lower position.and push slowly forward until the machine base tilts towards the ground. Make sure to put the wheels back on the ground in time to avoid the base from falling on the ground. This might cause damage! Check to make sure the power switch is in the “off” position. Set the handle position to the desired height by pulling and releasing the black knob with the left hand. While holding the black knob out, raise or lower the handle frame with your right hand. To fix the handle frame into place, release the black knob so that it locks firmly into one of the holes. To turn the machine on, press the power button on the end of the left handle. Position “0” is off and position “I” is on. Make sure a suitable pad or brush is mounted before starting the machine. The immediate contact of the floor and driver plate without a pad can lead to serious damage of the floor and/or the machine. 8.638-856.0 Manual Operators - Radiant Orbital Scrubber

For effective floor cleaning, move the machine forward and backwards. It is recommended to spray the floor as you move the machine forward, releasing the spray button when you move the machine backwards. To increase the pressure and cleaning effect on certain floor types like tile and grout, you can lift the machine frame up, raising the wheels off the ground. When lifting the wheels off the ground the full weight of the machine lies on the machine base. Make sure the surface the added pressure does not damage floor.Omit this measure on very sensitive floors. End of the Application Turn off the machine by putting the on/off switch to “O”. If a cleaning solution was used, fill solution tank with water and spray out system for 30 seconds or drain using draining port at bottom of tank. Make sure to not let solution come in contact with the motor. Storage To avoid damage to the handle frame, DO NOT lay the machine frame on the floor as done with other traditional cleaning equipment. Remove the pad from the driver plate by pulling it down firmly. Put the machine frame in an upright position by pulling the black knob with the left hand and move the handle frame upwards with the right hand. The black knob should lock firmly in the top hole. To allow an easy transportation of the machine, remove the weight kit if used. To easily roll the machine, push your foot on the back wheel axle to create leverage and pull the handle towards your body. The machine can be moved similar to a dolly now. 8.638-856.0 Manual Operators - Radiant Orbital Scrubber

Lifting and Carrying If you do not have a ramp, we recommend two people to life machine in and out of a vehicle. Put the handle into a firmly locked lower position. Make sure that the machine base rests on a pad, so that the grip surface of the driver plate does not get damaged or hooked onto a carpeted surface. When lifting the machine in or out of the vehicle, set the wheels down first, followed by the machine base. Make sure not to grip too close to the machine base. If the base should flip upwards it can cause serious hand injuries. Make sure you lift the machine with a back-friendly posture. Secure machine firmly so it will not move. Weight Kit Installation The total weight of the weight kit is 40 lbs. Put the weights on top of the mounting plates located on the sides of the machine base. Put the four screws into the holes provided on the weight plates and fasten by turning clockwise. Once the screws have threaded at least 5 full turns, tighten the wing nuts by turning them clockwise, until the weights fit securely to the base. Make sure that the weights are securely attached to the base. Loose weights can cause serious damage. For storage and transport we recommend removing the weight kit. The machine can be transported more easily without the weights. 8.638-856.0 Manual Operators - Radiant Orbital Scrubber

the foot of the bumper. Remove the driver plate by removing the four counter- sink screws in the center of the plate using an electric screwdriver. It is important to only use a Number 3 Phillips head screwdriver bit. Smaller bit sizes can damage the screw heads and leave sharp edges, which can tear or snag the pads. Damaged screws can cause further damage. Mount the brush with the same countersink screws used for mounting the driver plates. NOTE: Tighten the screws sufficiently to avoid disengagement of the brush from the machine during operation To avoid stripping the screws do not over tighten. An electric screwdriver with a clutch will ensure that stripping will not occur. Attaching and Removing the Driver Plates Put the machine base in an upright position, sitting on the foot of the bumper. Remove the driver plate by removing the four countersink screws in the center of the plate using an electric screwdriver. 8.638-856.0 Manual Operators - Radiant Orbital Scrubber

the holes of the driver plate with the appropriate threads of the bearing retainer ring. It is recommended to align the threads of the bearing horizontally to the ground. Put the four countersink screws through the holes of the driver plate and first screw them into the bearing retainer ring threads manually. Then, tighten the screws with an electric screwdriver • NOTE: Tighten the screws sufficiently to avoid disen- gagement of the driver plate from the machine base during operation.To avoid stripping the screws do not over tighten. An electric screwdriver with a clutch will ensure that stripping will not occur. Accessories And Applications Never store the accessories in wet conditions. Keep the accessories away from extreme heat and from chemi- cals. Driver Plates Exclusively use designed driver plates only. The use of other driver plates will damage the machine and its mechanical action. The driver plates are fastened on the machine base with four countersink screws. Standard Driver Plate The standard driver plate (17” in diameter) is supplied. It is suitable for use with all pads for textile and hard floor applications. The pads can be easily attached and removed from the driver disc. Never put the driver on the carpet without a pad attached, as this might cause serious damage to the floor. 8.638-856.0 Manual Operators - Radiant Orbital Scrubber

of fibers and latex that allows the gentle cleaning of heavily soiled short-pile carpets as well as the scrubbing of hard floors. Attach the AgiClean pads by centering them onto the driver plate. An AgiClean pad, used on both sides, cleans an approximate area of 1000 -2000 sq. ft (100 to 200m²), depending on the floor type and level of soil. Rinse the AgiClean pads after each use with clean water. Chemical Free Stripping Pad Chemical Free Stripping Pads are made of a unique material impregnated with diamonds. They can be used for deep cleaning and to remove wax off of vinyl, VCT, linoleum, wood, safety tiles and more. A Chemical Free Stripping Pad, used on both sides, cleans an approximate area of 1000-2000 sq. ft (100 to 200m²), depending on the floor type and the level of wax and soil. Make sure to thoroughly rinse the Chemical Free Stripping Pad with clean water after each use. Scrub Brush The bristles of the brush are made of high quality nylon. The unique brush design is ideal for cleaning tile and grout, smooth concrete, rubber flooring, and micro- porous surfaces such as porcelain and safety tiles. It can also be used for any other hard surfaces. Concrete Brush Our concrete brush is designed for outside concrete and other rough surfaces. It is great for cleaning walkways with minimal water. Never use the concrete brush on any other floor other than the specified outside concrete or rough surfaces, as this brush will cause serious damage to all other flooring. 8.638-856.0 Manual Operators - Radiant Orbital Scrubber

pads are specifically designed for the Radiant. Thoroughly remove moisture, soil, and lift carpet pile allowing faster dry times. A SuperZorb Pad, used on both sides, cleans an approximate area of 3000 sq. ft (280m²), depending on floor type and level of soil. SuperZorb Pads are machine washable and can be reused hundreds of times. The use of the multi-purpose brush may splash in certain applications. applications. Take appropriate measures or use a splash guard to prevent the wetting of walls and other obstacles. Rinse the brush as needed with clean water after each use. Depending on usage and care, you can use the multipurpose brush for many years. NOTE: ON STORAGE: Never store the multi-purpose brush with the bristles down. This can deform the bristles, damage the brush and reduce the cleaning performance. You can bring deformed bristles back into their original form by heating them with a heat gun. Application On Different Floor Types Carpet Cleaning Vacuum the carpet thoroughly before cleaning. Large dirt particles are removed, allowing the application to be more effective. Apply solution as you move forward. The carpet should be cleaned by going forward and backwards two to three times, while applying solution on the first pass in order to keep the drying time low. Depending on the level of soil and the nature of the carpet, this process can be shortened or extended. As required, carpets can be vacuumed again after cleaning. 8.638-856.0 Manual Operators - Radiant Orbital Scrubber

Remove dust and coarse dirt from the surface before cleaning. Choose a suitable pad according to the application. Place the pad in the center of the driver. Gently lower the head on to the floor. Surface can be cleaned by moving forward and backwards two to and adding water. Use a cleaning solution as needed. Depending on the soil contamination and the floor type, this process can be shortened or extended. 8.638-856.0 Manual Operators - Radiant Orbital Scrubber

Clean the machine with a soft cloth and a neutral pH cleaner. With scrub head resting in the vertical position, rinse bearing while rotating the pad driver or brush. Before emptying the solution tank, adjust the handle to the middle position so that the water drains behind the machine. Changing The Driver Grip Face Remove the ten outer screws that fasten the grip face disc on the driver plate. To save time, use an electric screwdriver with a #3 Phillips Head bit. The Number #3 Phillips head bit is slightly larger than standard size. It is important that you are using a #3 Phillips Head bit, as smaller bits can damage the screw heads and produce sharp edges which can damage the cleaning pads. Attach a new grip face disc to the driver plate using the ten screws. Make sure that the screws are very tight, not loose. If the screws are even slightly loose it can cause damage to the grip face disc. Ensure that the four holes in the middle of the grip face disc are aligned with the screws located on the driver plate. An exact alignment allows easy removal and installation of the driver plate. 8.638-856.0 Manual Operators - Radiant Orbital Scrubber

1.005-297.0 8.638-856.0 Manual Operators - Radiant Orbital Scrubber

20 9 1 10 8 7 11 13 14, 14a 22 23 2 26 25 27 15 4 18 16 19 5 6 17 3 24 16 18 12 24 15 21

Handle REF PART NO. QTY DESCRIPTION NOTES 1 86388570 1 WELD ASSY, HANDLE 2 86388580 1 FORK 3 86388590 1 COVER, ELECTRICAL BOX 4 86388600 1 ROD, HANDLE ADJUST 5 86388610 1 WELD ASSY, PULL LATCH 6 86388620 1 PULL LATCH 7 86388630 2 COVER, TUBE HANDLE, 1.5 DIA 8 86388640 1 SWITCH, DP POS, ROCKER 9 86388650 1 SWITCH, DP, 2POS, ROCKER SPR 10 86388660 1 BREAKER, 20A 125/250VAC 32VDC 11 86388670 1 STRAIN RELIEF, POWER CORD 12 86388680 1 LOCK NUT, E PANEL, .5-14 NPSM, ZNPLT 13 86388690 1 POWER CORD, 3 CABLE, GRAY 14 86388700 1 PLUG, MALE, EURO 220V 14a 86388710 1 PLUG, MALE, US 115V 15 86388720 3 HEX NUT, LOCK, .5-13 X .75W X .312H 16 86388730 5 WASHER, NYLON, .50 ID X .75 OD X .06 T 17 86388740 2 SHAFT COLLART, SET SCREW, .63 ID X 1.13 OD X .5 T, ZNPLT 18 86388750 4 WASHER, PLASTIC, .500 X .125 X 1.125OD 19 86388760 3 ZINC PLATED, 1/2"-13. 1-3/4" LONG 20 86388770 4 SCREW, THPM, 8-32 X .25, ZNPLT 21 86388780 1 SCREW, PHP, DRILLING, 6-20 X .38,ZNPLT 22 86388790 1 SCREW, HEX CAP, .500-13 X .875L 23 86388800 4 ZINC PLATED, 3/8"-16 THREAD, 1" LONG 24 86388810 8 WASHER, FLAT .38 X .06T X 1.0 OD, STL, ZNPLT 25 86388820 4 ZINZ PLATED, 3/8"-16 THREAD 26 86388830 2 ARMS PLASTIC BUSHING 1.00 LENGHT 27 86388840 2 NYLON PLASTIC WASHER 0.812" ID, 1.057" OD

5 8 4 14 6 13 9 3 1 12 2 13 10 11 12 7

Tank REF PART NO. QTY DESCRIPTION NOTES 1 86388850 1 TANK, VIBE 2 86388860 1 BRACE, TANK 3 86388870 1 CAP, DRAIN, 2" 4 86388880 1 CAP, DECK PLATE, 6" 5 86388890 1 FAUCET FILL 6 86388900 1 TUBING, .375 OD X .25 ID, BLACK 7 86388910 1 TUBING, FAUCET FILL, 26 INCH 8 86388920 1 VALVE, DUCKBILL 9 86388930 1 FITTING, ELBOW, SWIVEL, .25 NPT X .38 OD, NICKEL PLATE 10 86388940 1 STRAINER, FILTER 11 86388950 1 VALVE, MALE, CONNECTOR .53 DIA 12 86388960 4 WASHER, FLAT, .25 ID X .625 OD X .06 THK 13 86388970 4 1/4"-20 THREAD 3/4" LONG 14 86388980 6 ROUNDED HEAD THREAD-FORMING SCREW

6 9 1 10 22 21 7 4 19 5 13 17 8 14 23, 24 15 16 2 18 20 11 3 12

Motor REF PART NO. QTY DESCRIPTION NOTES 1 86388680 1 LOCK NUT, E PANEL, .5-14 NPSM, ZNPLT 2 86388810 10 WASHER, FLAT .38 X .06T X 1.0 OD, STL, ZNPLT 3 86388960 8 WASHER, FLAT, .25 ID X .625 OD X .06 THK 4 86388990 1 WELD BASE ASSY 5 86389000 1 BUMPER, 17 INCH 6 86389010 1 MOTOR, 1HP 7 86389020 2 WELD ASSY, SPACER PLATE 8 86389030 1 ASSY, COUNTERWEIGHT 9 86389040 1 “WASHER, BELLEVILLE, LOCK, .9 ID X 1.3 OD X .06 T, BLK” 10 86389050 1 LOCK NUT, E PANEL, .75-14 NPSM, ZNPLT 11 86389060 1 ELBOW, ELECTRICAL BOX, MOTOR 12 86389070 1 SCREW, SOCKET SET, .38-24 X 1.50 STL CUP POINT BLK OX 13 86389080 1 SHAFT SUPPORT 14 86389090 4 SCREW, HEX HEAD, .38-16 X .75, STL, GRD8, YL ZNPLT 15 86389100 4 SCREW, HEX CAP, .38-16 X .88, STL, GRD5, ZNPLT 16 86389110 2 SCREW, HEX CAP, .312-18 x .75, ZNPLT 17 86389120 4 SCREW, FHPM, .25-20 X 1.0, ZNPLT 18 86389130 8 HEX NUT, LOCK, .25-20 X .438W X .313H, ZNPLT 19 86389140 8 SCREW, THPM, .25-20 X 1.5, 18-8 SST 20 86389150 1 HANDLE SPRAYERS ASSY 21 86389160 1 WIRE MOUNT, ELECTRICAL BOX, MOTOR 22 86389170 1 HANDLE SPRAYERS BACK HOSE 23 86389180 1 17” UNIVERSAL DRIVER KIT 24 86389190 1 17” REPLACEMENT VELCRO DRIVER PLATE

8.638-856.0 Manual Operators - Radiant Orbital Scrubber 11 7 1 12 9 6 5 3 8 14 4 13, 13a 10 2 15 16

Frame, Wheels, & Pump REF PART NO. QTY DESCRIPTION NOTES 1 86388720 2 HEX NUT, LOCK, .5-13 X .75W X .312H 2 86388730 4 WASHER, NYLON, .50 ID X .75 OD X .06 T 3 86388750 4 WASHER, PLASTIC, .500 X .125 X 1.125OD 4 86388760 2 ZINC PLATED, 1/2"-13. 1-3/4" LONG 5 86388830 2 ARMS PLASTIC BUSHING 1.00 LENGHT 6 86388840 2 NYLON PLASTIC WASHER 0.812" ID, 1.057" OD 7 86389200 4 6-32 THREAD SIZE, 1-1/2" LENGHT 8 86389210 4 NUT 6-32, HEX NYLOCK STL ZNPLT 9 86389220 4 WASHER, PUMP MOUNT 10 86389230 2 WHEEL,10" 11 86389240 1 WELD ASSY TABS, BASE FRAME 12 86389250 2 SCREW, HEX CAP, .5-13 X 3.25, GRD 5, ZNPLT 13 86389260 1 PUMP, 115V 13a 86389270 1 PUMP, 220V 14 86389280 2 HEX NUT, LOCK, .38-16 X .563W, .266H, ZNPLT 15 86389290 1 FITTING, ELBOW 90 3/8 16 86389300 1 FITTING, ELBOW 90 1/4”

1 2 11 3 10 4 5 5 6 6 12 12 13 13 7 8 9

Spray Handle REF PART NO. QTY DESCRIPTION NOTES 1 86389310 1 FITTING, TEE, SPRAY NOZZLES 2 86389320 1 FITTING, 90 , SPRAY NOZZLES 3 86389330 1 HOSE, SPRAY NOZZLES 4 86389340 1 HOSE, SPRAY NOZZLES, PUMP 5 86389350 1 COUPLER, FILTER 6 86389360 1 STRAINER, CHECK VALVE 7 86389370 2 NOZZLE, SPRAYER 8 86389380 2 NOZZLE RETAINER 9 86389390 1 COUPLER, NOZZLE BASE PLATE 10 86389400 2 SLEEVE, COMPRESSION, CON 11 86389410 1 VIBE SPRAY HANDLE 12 86388810 2 WASHER, FLAT .38 X .06T X 1.0 OD 13 86389110 2 SCREW, HEX CAP 312-18 X .875 ZNPLT

2 (WHT) WHT 1 (BLK) 1 (BLK) BLK 2 (WHT) BLK BLK BLU ORG BLK 4 (RED) 1 (BLK) 3 (BLU) WHT WHT 2 (WHT) BLK YLW Ground Ground Ground Ground Ground Ground Motor Housing Pump Plug Wires Extra Plug SPRAY SWITCH Motor Wiring Box ON/OFF SWITCH Circuit Breaker Power Cord from Wall Terminal Strip inside handle wiring box 5(YLW) No Connection (Insulated) 6 (BRN) No Connection (Insulated)

Suggested Spare Parts REF PART NO. QTY DESCRIPTION NOTES - 86388640 - SWITCH, DP POS, ROCKER - 86388650 - SWITCH, DP, 2POS, ROCKER SPR - 86388660 - BREAKER, 20A 125/250VAC 32VDC - 86388940 - STRAINER, FILTER - 86375110 - ASSY, BEARING, 17 DISK - 86389360 - STRAINER, CHECK VALVE - 86389370 - NOZZLE, SPRAYER - 86389380 - NOZZLE, RETAINER