Wildfire PANAMA HE User Instructions

Text of Wildfire PANAMA HE User Instructions

It is a regulaon that these instrucons be handed to the customer aer installaon is complete. It is

also the responsibility of the installaon engineer to ensure that the customer is able to fully operate the appliance and is aware of any cleaning or maintenance requirements. PANAMA HE GAS FIRE Model number: F-061XX2 SLIDE for use on Natural Gas (G20) at a supply pressure

Wildfire PANAMA HE Regulatory Informaon and Installaon Requirements …………………………... 3

Installaon Requirements (connued) ………………………………………………….. 4 Sing the Appliance ……………………………………………………………………………… 5 Installaon of ‘fixing plate’ assembly …....………………………………………………. 6 Install

REGULATORY INFORMATION AND INSTALLATION REQUIREMENTS

THE FOLLOWING MUST BE NOTED PRIOR TO THE INSTALLATION OF THIS APPLIANCE. This gas appliance MUST be installed by a GAS SAFE registered installer by law. It must be installed in accordance to these installaon instrucons and the GAS SAFETY (Installaon & Use) REGULATIONS 1998 as amended. Non compliance of this law may lead to prosecuon and it is in the interest of you and your family that

Wildfire PANAMA HE No purpose made venlaon is normally required for this appliance when installed in G.B. If the appliance is

being installed in I.E then refer to I.S 813:1996 (Domesc Gas Installaon—Naonal Standards Authority of Ireland). Venlaon areas (if applicable) should be checked periodically to ensure there is no obstrucon, even though none is normally required for this appliance. SPILLAGE TEST: To check for sasfactory clearance

SITING THE APPLIANCE

Fireplace Opening IMPORTANT NOTE: This appliance DOES NOT seal onto a marble or stone back panel. The fire is installed directly onto the FIXING PLATE assembly. This is detailed on pages 6 & 7. This FIXING PLATE is also used to support the marble or stone back panel. This back panel should have the following cut- out : WIDTH 560mm—580mm HEIGHT: 585mm—605mm A non-combusble fireplace back panel is required w

Wildfire PANAMA HE Checking the Flue

Use a smoke pellet prior to the appliance installaon to ensure the viability of the flue and check that the smoke can be seen being emied from the terminal / chimney pot outside. There must be no leakage of smoke through the structure of the chimney/flue during or aer the smoke pellet test and it is important to check inside upstairs rooms adjacent to the chimney/flue. Check the chimney pot / terminal and general condi�

Installing the Back Panel

Ideally the back panel should be constructed from a 3 piece panel and reassembled using suitable materials. This type of back panel will ensure that no corner cracking occurs over me. A ’loose’ 3 piece panel can be installed but care should be taken to ensure that the joint line is square. Ensure that the FIXING PLATE is set to provide a 76mm (3”) distance from the front face of the back panel, to the wall (See be

Wildfire PANAMA HE Now unroll and fit the rock wool as shown below. This should sit around the perimeter of the FIXING PLATE.

Under NO circumstances should this fireplace be commissioned without the installaon of the Rockwool provided. Combusble Shelf This appliance may be fied below a surround with a combusble shelf providing the following dimensional criteria are met: There must be a minimum distance of 250mm from the top of the appliance to the unders

Connecng the Appliance to the Gas Supply

In all installaon condions the gas connecon should be provided using 8mm (O/D) copper tubing. No soldered joints should be used with the firebox of the appliance. The blind grommet which is supplied in the standard fing pack should be used to close up the knock out hole—simply cut a small cross with a sharp knife in the centre of the grommet—this will then seal around the gas pipe to provi

Removal of the front glass panel.

The top glass clamp is held in place with 3 screws. This panel is concealed behind the top cover strip which is held in place by two magnets. The two magnets are fied to the top glass clamp as shown in this diagram. Carefully remove the 3 fixing screws and whilst supporng the glass panel, remove the clamp. Now li the glass from the appliance. The boom edge of the glass is retained in the two supports

Install the ceramics into the appliance according to these instrucons—see pages 17 through to 23.

Refit the glass panel and the decorave strip to cover the screws and retaining clamp—See page 10 Test the operang pressure of the appliance by aaching a pressure gauge to the test point of the appliance. This connecon should take place when the appliance is OFF. Ensure that gas is turned on at the gas meter and purge the air from t

Compleng the Installaon of the Appliance

Remove the protecve covering (if applicable) from the face of the decorave trim. To fit the trim to the appliance the four adjustable mounng features at the rear of the trim need to be set. To allow for a tolerance with the installaon the trim can be adjusted to sit fore and a as is required to give a neat fit of the trim. The trim should ideally sit approximately 1mm in front of the b

Appliance Technical Informaon

Gas Type : Natural Gas Category : I2H Inlet Pressure: (Cold) 20mbar Heat Input Gross : 5.3kW Injector : 69 Desnaon Countries : GB/ IE HEALTH AND SAFETY NOTICE This appliance uses fuel effect pieces manufactured from Refractory Ceramic Fibres (RCF). Care must be taken to avoid excessive exposure to these materials as they may cause irritaon to the eyes, skin, nose and throat. When handling, avoid inhaling

Cleaning the Appliance (connued)

Trim, Fret and Painted Metal Parts There are a variety of trim and fret opons which may have been supplied with your appliance and these are normally a plated material on a steel substrate. It is important that no abrasive cleaners or chemical agents are used in the cleaning of these components. It is recommended that all these surfaces including the painted metal parts are cleaned with a clean damp (not wet) c

Removal / Replacement of Gas Carrying Components (connued)

Slide Control Valve 1. Remove the locknut from the front of the valve. 2. Undo the three (3) nuts around the periphery of the valve body—Gas Inlet / Burner / Pilot. 3. Remove the thermocouple nut from the back of the valve. 4. The valve can be removed and serviced / replaced as necessary. 5. Re-assemble in reverse order. 6. Re-assemble the burner tray into the firebox (see previous pag

This appliance is available with two operang methods, namely manual control and slide control. The following

instrucons detail both methods of operaon however the basic operaon of the appliance involves the ignion of a pilot burner (See page 11 for spillage monitoring details—ODS), then the control of the main burner with LOW and HIGH sengs. This appliance has a naked flame and as with all heang applian

FUEL BED LAYOUT

The following instrucons detail how the ceramic fuel bed and loose components are to be installed onto the appliance. Great care should be taken when handling these ceramic parts as they are fragile and can easily be broken. Do not force any component into posion, if it does not fit easily then you are not fing the part correctly. These instrucons can also be followed to remove or reinstall the fuel bed aer cleaning.

Fit the Right Hand front ceramic rail in front of the burner as shown in the picture below.

Step 4 Fit Log A onto the fuel bed as shown in the picture below.

Wildfire Indoor Fireplace Owners Instructions: