Hayward Aqua Plus® Operation Manual

Operation Manual for models PL-PLUS PL-PLUS-20 Aqua Plus ® www.hayward.com ...

When using this electrical equipment, basic safety precautions should always be followed, including the following: • READ AND FOLLOW ALL INSTRUCTIONS • ! WARNING: Disconnect all AC power during installation. • ! WARNING: Water in excess of 100 degrees Fahrenheit may be hazardous to your health. • ! WARNING: To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at ...

System Overview Block Diagram....................................................................... 1 Automation............................................................................. 1 Chlorination............................................................................ 1 Default Display....................................................................... 2 Manual System Filter Pump............................................ ...

Plus can control pumps, valves, lighting, heaters, and chlorination. Although the Aqua Plus is easy to use, it is important to completely read through this operating manual before attempting to operate the control. NOTE: This manual assumes that the Aqua Plus has been wired and configured according to the Installation Manual. A ...

(150,000 liters), or the needs of most commercial pools up to 25,000 gallons (95,000 liters). Check local codes for other restrictions. The actual amount of chlorination required to properly sanitize a pool varies due to bather load, rainfall, temperature, and the pool’s cleanliness. For pools larger than 40,000 gallons, the Aqua Plus ca ...

While the main objective of the Aqua Plus is to automate the operation of your pool/spa system, there may be certain times when you want to override the automatic operation and control the equipment manually. To operate the pool equipment manually while keeping the automation active, perform the following procedures. Note that if you turn a relay on manually, it will remain on until either you turn it off manually, or the next t ...

Standard Relay: Manual operation of all 3 relays is identical. Assuming that the relay is currently off, simply press the appropriate button to turn on the relay. If the relay does not turn on, it probably is due to the “interlock” feature (which was set up in the Configuration Menu) being activated that requires the filter pump to be running and the valves to be in the pool-only position. This protects pumps and othe ...

The Aqua Plus controls most of your pool equipment automatically in order to minimize the time spent working on your pool. Most of the pool equipment can be programmed to operate on a timeclock basis. In addition, the desired pool and spa temperatures and pool and spa chlorinator settings can be programmed. This section will guide you on how to program the automatic operation for each function. The programming of automatic ...

The Aqua Plus’s six menus have many items that allow you to customize the operation of your pool/spa equipment. The chart below shows the Aqua Plus’s menus as well as each menu’s specific settings. denotes conditional items default menu day and time water temperature air temperature chlorinator setting salt level reason pump is running (not scheduled) inspect cell reason hi-speed is running (not scheduled) countdown time ...

nothing to set. The Aqua Plus will automatically switch to the default menu when no keys have been pressed for 2 minutes and will then scroll through each display. The Settings Menu and the Timers Menu are the menus you will be using most often to adjust the operation of your pool. The Configuration Menu is used when the system is installed ...

+ to enter Filter Speed 1 95% Push to access Variable Speed Pump Speed Settings Move to previous/next configuration menu Spa Speed 50% Move to next menu item only if Pool and Spa and Filter is Variable Speed only if an output is configured for a variable speed pump only if Filter is Variable Speed Set the desired Filter Speed 1 from the Filter Lowest to the Filter Highest Move to next menu item Aux1 Speed 95% Set the desired Aux1 Speed ...

Wednesday 10:37P Adjust the current day of the week Move to hours setting Set Day and Time 10:37P Set Day and Time Wednesday 37 Set Day and Time Wednesday 10: P Adjust the current hour (including AM/PM if applicable) Adjust the current minute Move to minutes setting Move to previous/next menu item Use this function to set the current day of the week and time. These values are used for all the automatic timeclock ...

Teach Successful Wireless Teach NOT Successful Wireless Teach Wireless Base NOT Found Press and hold wireless button Push to start process Move to previous/next menu item Move to previous/next menu item Move to previous/next menu item Move to previous/next menu item Move to previous/next menu item Press any button on wireless remote This menu will only appear if a wireless base station is connected to the Aqua Plus. Perform ...

for the pool. For pool/spa combination systems with spillover enabled, the valves will automatically switch to spillover mode at the start of the filtration period. For all other systems, the valves will switch to the pool-only position. For two speed, this setting will be the period of time when the pump runs at high speed (the word “Filter T1 ...

spa time, the Aqua Plus will turn on the filter pump and move the pool/spa valves into the “spa-only” position. The heater will automatically heat the spa up to the programmed spa temperature (page 7). This programmed spa operation will take precedence over all other automatic functions, only manual operation of the filter button or pool/spa valv ...

designated times. There is no manual override. If the Valve3 relay is on during the programmed off time, it may be because of freeze protection. Super Chlorinate 24 hours Adjust Superchlorination period (1 - 96 hours) Move to previous/next menu item For larger pools or when you have an unusually high bather load, a large amount of rain, a cloudy ...

Pool/Spa Setup Pool and Spa Spa Spillover Enabled Filter Operation Spa Spillover Push to access Pool/Spa options Rotates between Pool Only (default), Spa Only and Pool and Spa Toggle between Enabled and Disabled Spa Spillover (default) Toggle between Pool Only and Spa Spillover options (default) Move to previous/next configuration menu Move to next menu item Move to next menu item or previous/next configuration menu ...

Filter Pump 1 Speed Freeze Protect Enabled Lowest Speed 10% Highest Speed 100% Push to access pump options Rotates between 1-speed (default), 2-speed and variable speed options Toggle between Enabled (default) and Disabled Freeze Protection Adjust the lowest speed desired for variable speed operation Adjust the highest speed desired for variable speed operation Move to next menu item Move to previous/next configuration me ...

Select the temperature to be used for freeze protection. Temperature is adjustable from 33ºF-42ºF (1ºC- 6ºC). 38ºF (3ºC) is default. This threshold will be used for all outputs that have freeze protection enabled. External Input Interlock When enabled, the filter pump will be forced off when the external input is active. Note that freeze protection will have precedence over this feature. Heater1 Config. + to view/c ...

Solar Disabled Solar-Extend Disabled Solar Priority Disabled Push to access solar options Toggle between Enabled and Disabled (default) Solar Toggle between Enabled and Disabled (default) Solar Extend Toggle between Enabled and Disabled (default) Solar Priority Move to previous/next configuration menu Move to next menu item or previous/next configuration menu Move to next menu item Move to next menu item if “Solar” is ...