Lightwave LW821 Instruction Manual

Model No. LW821 Instruction Manual Version 2 ...

Responsible Authority: LightwaveRF PLC, Innovation Campus Birmingham Faraday Wharf Holt Street Birmingham B7 4BB Tel: +44 (0)121 250 3625 Email: [email protected] Model Number(s): JSJSLW821 Description: Inline Relay Directives this equipment Complies with: 2006/95/EC The Low Voltage Directive N/A 2004/108/EEC The Electromagnetic Compatibility Directive 1999/5/EC R&TTE Directive 93/68/EEC CE Marking Directive Standards A ...

How do I get started? The relay is designed to remotely turn on/of lighting or power circuits (max 500W) or to control door, window or curtain openers. You must understand how your devices need to be wired and how to safely turn of the electricity supply. You will also need suitable electrical screwdrivers. Please refer to the following installation and setup instructions that will guide you through the installation and setup process. Help ...

illuminated the relay is powered. Mounting hole. On/of & linking button. Overview IMPORTANT: All LightwaveRF products can be legally DIY installed in your own home; however, if in doubt, always consult a qualified electrician or heating engineer. It is important to install this product in accordance with the following instructions. Failure to do so may void your warranty. Installation Fuse compartment. Wiring terminals. Screw cover. ...

to 500W of mains powered switching OR separate volts free switching for circuits not requiring additional mains power. The relay latches between three positions: switched live 1, switched live 2 and a neutral position (not connected). IMPORTANT: The Inline relay is not designed to be left exposed once it is installed, as live mains wiring is connected to the termina ...

terminals, as shown in the diagram, to provide power to the relay. When the green LED is illuminated, the relay is connected to mains power. NOTE: Even if switching a low voltage or non-mains circuit, the relay must always have mains power connected to the live and neutral terminals for it to be able to function. Installation COM L N L N Live wire Neutral wire Connecting to a circuit volts free Use this confi ...

connected IMPORTANT: When the relay is operated remotely via RF, it is always the lefthand load terminal that will be connected when the ‘on’ button is pressed. Therefore, if the circuit is wired as shown, pressing ‘on’ using an RF remote will turn on the circuit, and ‘of’ will disconnect it. COM L N L N Of Position - circuit disconnected 2. Connect the outgoing wire � ...

COM L N L N Position 2 - circuit 2 connected Switching between two Circuits If a second load wire connected to another circuit is attached to the second switched live terminal (see diagram), the relay can be used to switch between two circuits. In addition to the on and of positions, there is also a ‘stop’ position which breaks contact w ...

be able to utilise the ‘on’ and ‘of’ commands to switch between circuits but NOT use the stop command, as it does not include this function. To operate the stop command you will need a LightwaveRF ‘On/Of/Stop Switch’ which includes ‘on/of’ (open/close) and ‘stop’ commands OR the LightwaveRF App (requires Lightwave Link). If you are using the App, you mu ...

(interupt) a mains powered circuit (max 500W load), then power must be taken from the relay’s main live terminal via a jumper connection to the common terminal (see diagram). The neutral terminal must now also accommodate an incoming and outgoing connection to the mains circuit. COM L N L N NOTE: Because of the extra ‘stop’ command, a LightwaveRF ‘On /of/st ...

NOTE: This procedure applies to the LightwaveRF Smartphone and Web App and all LightwaveRF controllers (e.g. Handheld Remote or Mood Controller). LightwaveRF relays each have 6 unique memory slots which means they can link with up to 6 LightwaveRF controllers in total. If you are using a smartphone/tablet/PC to control the relay via the Lightwave Link, this will always count as ONE controller and take ...

controller during this time then the socket will automatically exit linking mode without linking the device. If, when expecting a quick flashing LED to confirm pairing, a slow flash is received instead, then the relay memory is FULL and no further remotes may be linked with it unless one of the existing remotes is unpaired first (see below). 1. On the relay, press and hold down th ...

up to 100m outdoors using the Lightwave Link. This figure may vary depending upon the environment; very thick walls, bodies of water or large metal objects may interfere with radio range. If the distance between the transmitter and receiver is too great to achieve reliable operation, the LightwaveRF Signal Booster may be used in conjunction with this product to increase the range. IM ...

Remote operation Remote operation Control using an on/of transmitter such as the handheld remote 1. Press the ‘on’/’open’ button on the transmitter to turn the circuit on or switch between circuits. 2. Press the ‘of’/‘close’ button on the transmitter to turn the circuit of or switch between circuits. 3. Press the ‘stop’ button to disconnect both circuits and cut power to connected de ...

Input rating: 220-240V~ 50Hz. Output rating: 500W Max. Dimensions: Width 68mm, Height 52mm, Depth 27mm Standby Energy Use: Less than 1W Warranty: 2 year standard warranty Technical specification ...

Mundells Welwyn Garden City Herts AL7 1FS 01707 386035 www.lightwaverf.com ...