Nexx SX.COM 2 Operation & User’s Manual

Sena Technologies, Inc reserves the right to make any changes and improvements to its product without providing prior notice. Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. 20S™, PRISM™, Snowtalk™, SX.COM 2™, SMH10™, SMH5™, SMH5-FM™, SPH10™, SPH10H-FM™, SMH10R™, SPH10S™, SPH10H™, SR10™, SR10i™, SMH10™, EXPAND™, Bluetooth Pack for G ...

2. PACKAGE CONTENTS ........................................................................5 3. GETTING STARTED .............................................................................6 Installing the SX.COM 2 ...............................................................................6 Powering On ............................... ...

Intercom for Scooters and Motorcycles. With the SX.COM 2, you can call handsfree on your Bluetooth mobile phone, listen to stereo music or GPS navigation voice instructions via Bluetooth, and have intercom conversations in full duplex with a passenger or other riders. The SX.COM 2 is compliant with the Bluetooth specification 3.0 supporting the following profiles: He ...

Status LED Speakers Microphone (–) Button (Intercom) (+) Button (Phone, Music) Pin-hole Reset Button DC Power Charging & Firmware Upgrade Port USB Power & Data Cable Microphone Sponges Hook and Loop Fasteners for Speakers ...

Installing the SX.COM 2 on Your Helmet 1.Peel off the hook fasteners for the speakers and attach them on the back sides of the speakers. 2. Attach the loop fasteners for the speakers in the deep ear pockets of your helmet. 1 2 ...

fasteners, centered to your ear. 4. Locate the microphone as closely as possible to your mouth when wearing the helmet. 5. Hide the wire under the helmet padding after the installation 5 ...

You can charge the SX.COM 2 by connecting the supplied USB power & data cable into a computer USB port or USB wall charger. You can use any standard micro-USB cable to charge the SX.COM 2. The LED turns red while charging, and turns blue when the headset is fully charged. It takes about 2.5 hours to fully charge. Note: Please make sure to take off your SX.COM 2-installed helmet while charging. Powering On Press and hold the ...

of the SX.COM 2. 2. The USB wall charger is not included in the package. Any 3rd party USB charger can be used with Sena products if the charger is approved by either FCC, CE, IC, or other locally approved agencies that Sena accepts. Please contact Sena regarding locally approved agencies Sena accepts. Checking Battery Level You can check the battery level in two diffe ...

When the battery is low, the blinking blue LED in stand-by mode turns to red and you will hear mid-tone triple beeps and a voice prompt saying “Low battery”. Adjusting the Volume Level You can easily adjust the volume by pressing the (+) Button or the (–) Button. You will hear a beep when the volume reaches maximum or minimum level. The volume is set and maintained independently at different levels for each audio sourc ...

Function Operations Power On/Off 1 sec. 1 sec. + Power On 1 press 1 press + Power Off Volume Adjustment 1 press 1 press or Intercom Pairing pairing A B 1) 5 sec. 5 sec. 2) 1 sec. Function Operations Bluetooth Pairing (Phone, MP3, GPS) 1) Sena 3S v1.1 5 sec. 2) Sena 3S v1.1 Select NEXX SX.COM 2 3) Sena 3S v1.1 Enter PIN Start & End Intercom Conversation 1 sec. Configuration 10 sec. ...

...

BLUETOOTH DEVICES Mobile Phone Pairing 1 Turn on the SX.COM 2 and press and hold the (+) Button for 5 seconds until the LED flashes red and blue alternately and you hear multiple beeps. You will hear a voice prompt saying “Phone pairing”. 2. Search for Bluetooth devices on your mobile phone. Select the NEXX SX.COM 2 in the list of the devices detected on the mobile phone. 3. Enter 0000 for the ...

2nd Mobile Phone Mobile Phone Pairing HFP + A2DP HFP Multipoint Pairing Multipoint Mobile Phones Pairing Bluetooth Stereo Device Pairing 1. If the Bluetooth stereo device is integrated with the mobile phone such as smartphones, you don’t need to pair the SX.COM 2 with it separately. When the SX.COM 2 is paired with the mobile phone, it is also paired as a stereo music device. 2. If you have a stand alone Bluetooth st ...

If you use GPS only for turn-by-turn voice instructions, not for Bluetooth stereo music streaming, multipoint pairing is recommended for the GPS connection. Multipoint Bluetooth pairing allows the SX.COM 2 to connect two HFP devices at the same time: mobile phone and GPS navigation. Follow the steps below to pair the GPS using the multipoint pairing. 1. Turn on the headset and press and hold the (–) Button for 5 ...

If GPS is not only used for turn-by-turn voice instructions but also is your preferred Bluetooth stereo music source, you can pair the GPS to the SX.COM 2 by following the simple procedures in “Mobile Phone Pairing”. When you do this, the SX.COM 2 thinks the GPS is a mobile phone. But the SX.COM 2 can directly pair an additional mobile phone. Note: You have to use a motorcycle specific GPS which transmits turn-by ...

1. When you have an incoming call, simply press the (+) Button to answer the call. 2. You can also answer the incoming call by loudly speaking any word of your choice if Voice Activated Phone Answering, VOX phone is enabled. (Refer to “Enabling/Disabling Voice Activated Phone Answering” for details.) 3. To end a call, press and hold the (+) Button for 2 seconds until you hear a mid-tone single ...

Pairing with Other SX.COM 2 Headsets for Intercom Conversation The SX.COM 2 can be paired with another headset for Bluetooth intercom conversation. 1. Turn on the two SX.COM 2 headsets (A and B) that you would like to pair with each other. 2. Press and hold the (–) Button of the headset A and B for 5 seconds until the red LEDs of both units start to flash rapidly. You will hear a voice prompt saying “Intercom pairin ...

call. You have to hang up the mobile phone call to make or receive an intercom call. Intercom Failure When you try to start an intercom conversation with an intercom friend who is already having a mobile phone call with another person, you will hear a low tone double beep signifying a busy signal. You will also hear a voice prompt saying “Intercom failed, try again late ...

(1) VOX phone (2) Voice prompt (3) Delete all pairings (4) Factory reset (5) Exit configuration Enabling/Disabling Voice Activated Phone Answering Voice Prompt “VOX phone” Factory Default Enable Enable / Disable Press the (–) Button If this feature is enabled, you can answer incoming calls by simply saying a word loudly enough, unless you are connected to intercom. For example, when you h ...