Milwaukee 4262-1 Operator's Manual

ELECTROMAGNETIC DRILL PRESSES Cat. No. 4204-1 4206-1 4208-1 4210-1 Cat. No. 4202 4203 TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S MANUAL. OPERATOR'S MANUAL ...

WORK AREA SAFETY ELECTRICAL SAFETY • Keep work area clean and well lit. Cluttered or dark areas invite accidents. • Do not operate power tools in explosive atmos- pheres, such as in the presence of fl ammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. • Keep children and bystanders away while operating a power tool. Distractions can cause you to lose cont ...

face, always use safety chain. Mounting can release. (See “Safety Chain” under “Operation) • Clean the surface before attaching the drill stand to the work surface. Paint, rust, scale, or uneven surfaces decrease the holding strength or the magnet. Chips, burrs, dirt and other foreign matter on the surface of the magnetic base will also decrease holding power. • Do not attach magnetic base to non ...

4. Drill motor 5. Grease fi tting 6. Gib adjusting screws 7. Chuck 8. Housing 9. Magnet 10. Adjusting handle 11. Cord 12. Control panel 13. Control panel socket 14. Wing screw assembly 15. Feed handle 16. Feed handle grip FUNCTIONAL DESCRIPTION Double Insulated DANGER! To reduce the risk of injury, always keep hands, rags, clothing, etc. away from moving parts and chips ...

Fig. A GROUNDING WARNING Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualifi ed electri- cian if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the cord or plug is damaged. If damaged, have it repaired by a MILWAUKEE service facility before use. I ...

1. Assemble the feed handles and grips to the feed handle hub. Tighten securely. 2. To mount the feed handle to the opposite side, remove the wing screw assembly that secures the hub/pinion assembly. Pull out the hub/ pinion assembly and insert on the other side of the housing. Replace and tighten the wing screw assembly. Mounting the Drill on Slide To provide maximum holding power, mount the motor with the spindle closes ...

reduces the magnet’s contact area which can result in the magnet coming loose. Surface Preparation Paint, rust, scale or uneven surfaces decrease the holding strength of the magnet. Chips, burrs, dirt and other foreign materials on the surface of the magnetic base will also decrease holding power. Use a smooth, fl at fi le to keep the magnet clean and free of nicks. Clean the surface before attaching ...

Fig. 6 1. Turn the drill motor off. 2. Position the magnetic base so that the drill bit is near the desired hole location and push the magnet button. The red indicator light will turn on. 3. Loosen the adjusting handle located at the back of the housing base. Move the housing to position the drill bit over the center of the hole. Tighten the adjusting handle securely. Keyed Chuck (Select Models) 1. Open the chuck jaws wide enough to inse ...

drilled. When proper alignment is established, ener- gize the magnet and start the drill motor. A pilot hole is recommended for drilling holes larger than 1/2” in diameter. When drilling, apply only enough force to produce a curled chip. Applying too little force will result in small broken chips and increased drilling time. Applying too much force will cause overheat- ing of the bit r ...

Set the drill rotating speed to the recommended speed. 2. Position the workpiece or tool so that the center pin is directly over the desired drilling location. 3. The use of HAWG WASH™ cutting fl uid is re- quired for long life of these cutters (see "Lubrica- tion"). Attach the hose to the oil fi tting on the side of the arbor and to your lubricant reservoir. 4. Swing the arbor arm in the direction of t ...