Maestro M1002G Operation & User’s Manual

SMARTPACK USER MANUAL VERSION 5 FOR APPLICATION VERSION 2.2.3 ON M1002G, M1003G, M1003G485, M100CDMAPLUS, M100CDMA485 WWW.MAESTRO-WIRELESS.COM EMAIL: [email protected] TEL: (+852) 2869 0688 FAX: (+852) 2525 4701 ADDRESS: 9/F, 121 KING LAM STREET, CHEUNG SHA WAN, HONG KONG ...

[email protected] ...

First Issue Samuel Chéreau 2 22 Jul 2013 Add details on M100 3G GPS commands on Chapter 23 Correct input command string details in section 21.4 Edited pictures for GPIO connections Add details on IOBR, IOBW commands Typo Samuel Chéreau 3 26 Feb 2014 Update for 097g Added command to switch from WipSoft and SmartPack Added command to reset all SmartPack settings to default Added debug comman ...

Maestro Wireless Solutions Ltd. reserves the right to modify or improve the product and its accessories which can also be withdrawn without prior notice. Besides, our company stresses the fact that the performance of the product as well as accessories depends not only on the proper conditions of use, but also on the environment around the places of use. Maestro Wireless Solutions Ltd. assumes no liability for da ...

12 1.2 Erasing the SmartPack application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 1.3 Switch between WipSoft and SmartPack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 1.4 Reset SmartPack settings to default value . . . . . . . . . . . . . . . . . . . . . ...

37 6 Dynamic DNS 39 6.1 Description of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 6.2 Dynamic DNS server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 6.3 Dynamic DNS account . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

63 12.2 Activating I/O triggered AT command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 13 Analog Input triggered AT command 67 13.1 Description of the operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 13.2 Activating analog triggered AT command . . . . . . . . ...

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 20.3 Executing a Command String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 20.4 Editing a stored Command String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 20.5 Add and edit phone number for Command String SMS service . . . . . . . . . . . . . . . . . . . . . . 91 2 ...

117 25 Example of modem software setup and operation 119 26 Command string - Quick reference 125 27 Known issues 127 28 SmartPack change log 129 29 Related documents 131 29.1 Related documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 29.2 Related software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 Confidential, th ...

[email protected] ...

utility range of various industrial and automated applications, such as: – Automatic and self-recovery TCP/UDP socket connection – AT command driven TCP/UDP socket connection – Ping Service – Dynamic DNS – Input/Output and Analog1 triggered AT command – Email sending (SMTP) – Remote AT command through SMS and ...

AT+VAFV Display the revision details of the SmartPack installed on Maestro modem Syntax: AT+VAFV Response: _SMARTPACK___<firmware>_ Defined Values: is the modem type, either: M1002G for the cellular/EDGE version. M1003G for the WCDMA version with gpsOne engine and USB connection. Applies also to the RS- 485 variant. M100CDMAPLUS for the Verizon CDMA version with gpsOne engine and USB co ...

AT+SPMODE Enable user to switch to standard Sierra Wireless WipSoft if the SmartPack commands are not required. Syntax: AT+SPMODE= Response: OK Defined Values: defines the application which runs on top of OpenAT: 0 SmartPack will run normally (Default value) 1 WipSoft will run and SmartPack commands are deactivated. Example: Command Response AT+SPMODE? +SPMODE: 0 OK AT+SPMODE=1 OK Note: WipSoft is act ...

AT+IPDEBUG Configure embedded TCP/IP stack debug message to be sent out or not Syntax: AT+IPDEBUG= Response: OK Defined Values: defines the output port of debug message: 0 disable debug message (default), 1 debug message on main serial port, 2 (reserved), 3 debug message on USB COM port (M100 3G). Example: Command Response AT+IPDEBUG=1 OK Note: Enable the debug message on main serial port. AT+IPDEBUG=3 ...

AT+SERIAL=? +SERIAL: (300,600,1200,2400,4800,9600,19200,38400,57600,115200), ("8N1","8O1","8E1","8N2","7N1","7O1","7E1","7N2") OK AT+SERIAL=9600,"8E1" OK Note: set the new settings for the serial port Note: – This command won’t be set when the SmartPack is in SPMODE=0, customer will have to set his serial port properly in this case. 1.7 Force device LED to be off AT+LED Enable ...

[email protected] ...

Describes how to setup cellular and TCP/UDP parameters to use the Automatic and AT command driven TCP/UDP connection, PING service, Dynamic DNS support. 2.1 CellularNetwork Parameters Following parameters are needed for cellular connection: – Access point name (APN) – User name – Password Those parameters have to be set using the AT+IPGPRS command. Please contact your network operator if you need any as ...

can be defaulted to +IPGPRS: 1,"Verizon","","" for Verizon Wireless version. 2.1.2 Activating cellular connection AT+CGATT Standard AT command to attach or detach to cellular network. For more details please refer to the AT command guide. Syntax: AT+CGATT= Response: +CGATT: Defined Values: 0 detached from cellular. 1 atta ...

AT+IPCONNECT=1,1 +CME ERROR: 3 Note: Operation not allowed. AT+IPCONNECT=1,1 +CME ERROR: 149 Note: PDP authentification failure AT+IPCONNECT=1,0 OK Note: Deactivating IP connection success. AT+IPCONNECT? +IPCONNECT: 1,0 OK AT+IPCONNECT=? +IPCONNECT: (0-1),(0-1) OK Note: – Before connecting to IP make sure to: • Enter APN settings by AT+IPGPRS command detailed in Sect ...

the specified . TCP connection will be active upon getting socket connection request from an allowed remote TCP peer specified in