Cisco IR829 Hardware Installation Manual

170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Cisco IR829 Industrial Integrated Services Router Hardware Installation Guide July 2017 Text Part Number:

INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY. The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense. The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are encouraged to try to correct the interference by using one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE. IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. Cisco IR829 Industrial Integrated Services Router Hardware Installation Guide © 2017 Cisco Systems, Inc. All rights reserved.

Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Objective . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Searching Cisco Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Obtaining Documentation and Submitting a Service Request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Product Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 SKU Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Hardware Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Platform Features for Cisco IR829 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Antennas and Installation Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Coexistence of radio standards: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Vehicular 5-in-1 and 2-in-1 installation and deployment notes. . . . . . . . . . . . . . . . . . . . . . . . 20 Modem Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Supported Cisco Antennas and Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 4G/LTE Radio Cables/Antennas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 4G/LTE Radio Cables/Antennas Use Case 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 4G/LTE Radio Cables/Antennas Use Case 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 4G/LTE Radio Cables/Antennas Use Case 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 4G/LTE Radio Cables/Antennas Use Case 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4G/LTE Radio Cables/Antennas Use Case 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4G/LTE Radio Cables/Antennas GPS Use Case 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Single Band Cisco WiFi Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Supported Single Band Cisco WiFi Antenna Use Case 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Supported Single Band Cisco WiFi Antenna Use Case 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Supported Single Band Cisco WiFi Antenna Use Case 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Supported Single Band Cisco WiFi Antenna Use Case 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Supported Single Band Cisco WiFi Antenna Use Case 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Dual Band Cisco WiFi Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Supported Dual Band Cisco WiFi Antenna Use Case 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Supported Dual Band Cisco WiFi Antenna Use Case 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

7 in 1 Antenna Configuration for Transportation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Transportation Use Case 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Transportation Use Case 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 SFP Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 RJ45 Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 RS232 Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 RS485 Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Installing the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Equipment, Tools, and Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Items Shipped with your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Additional Items. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Ethernet Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Installing the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Accessing the SIM Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Installing Antennas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Mounting on a Wall, Table, or Other Flat Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Installing the Router Ground Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Connecting the Router. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Preparing to Connect the Router. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Preventing Damage to the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Connecting a PC, Server, or Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Connecting a Terminal or PC to the Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Connecting to DC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Plugs and Pin-Outs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Constructing a Power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Wiring the DC Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Vehicle Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Verifying Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Router Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Preface This preface describes the objectives, audience, organization, and conventions of this guide and describes related documents that have additional information. It contains the following sections:  Objective, page 3  Audience, page 3 Organization  Conventions, page 4  Safety Warnings, page 4  Related Documentation, page 10  Searching Cisco Documents, page 10  Obtaining Documentation and Submitting a Service Request, page 10 Objective This guide provides an overview and explains how to install, connect, and perform initial configuration for the Cisco IR829. Previous versions contained additional configuration information which has now been relocated to the Cisco IR800 Integrated Services Router Software Configuration Guide. Audience This guide is intended for people who have a high level of technical ability, although they may not have experience with Cisco software. Organization This guide is organized into the following chapters. Chapter Name Description Chapter 1 Chapter 2, “Product Overview” Describes the router models and the hardware features available.

NOTE: Means reader take note. Notes contain helpful suggestions or references to additional information and material. CAUTION: This symbol means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data. TIP: Means the following information will help you solve a problem. The tip information might not be troubleshooting or even an action, but could be useful information. WARNING: IMPORTANT SAFETY INSTRUCTIONS Means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Safety Warnings Chapter 2 Chapter 3, “Installing the Router” Lists the items shipped with the router, the equipment and tools necessary for installing the router, the safety warnings and guidelines, and the procedures for installing the router. Chapter 3 Chapter 4, “Connecting the Router” Describes typical connections for the router, procedures for connecting the router to various devices, and how to verify the connections. Chapter 4 Chapter 5, “Technical Specifications” Provides the router, port, and cabling specifications. Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071 SAVE THESE INSTRUCTIONS Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen. BEWAAR DEZE INSTRUCTIES

kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla. SÄILYTÄ NÄMÄ OHJEET Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden. BEWAHREN SIE DIESE HINWEISE GUT AUF. Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento. CONSERVARE QUESTE ISTRUZIONI Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten. TA VARE PÅ DISSE INSTRUKSJONENE

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo. GUARDE ESTAS INSTRUÇÕES ¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONES Varning! VIKTIGA SÄKERHETSANVISNINGAR Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo. GUARDE ESTAS INSTRUÇÕES Advarsel VIGTIGE SIKKERHEDSANVISNINGER Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER

other cables/adapters could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO. The use of cables that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not limited to CISCO-designated products. Statement 371 WARNING: Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 378 WARNING: To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables. Statement 1021 WARNING: This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024 WARNING: If the symbol of suitability with an overlaid cross appears above a port, you must not connect the port to a public network that follows the European Union standards. Connecting the port to this type of public network can cause severe personal injury or can damage the unit. Statement 1031 WARNING: Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950 based safety standards. Statement 1033 Requirements in IEC 60950 based safety standards. Statement 1033 WARNING: When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046

with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54). Statement 1052 WARNING: No user-serviceable parts inside. Do not open. Statement 1073 WARNING: Installation of the equipment must comply with local and national electrical codes. Statement 1074 WARNING: Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 WARNING: Read the installation instructions before connecting the system to the power source. Statement 1004 WARNING: Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 WARNING: The covers are an integral part of the safety design of the product. Do not operate the unit without the covers installed. Statement 1077 WARNING: Hot surface. Statement 1079 Related Documentation  Cisco IOS Release Notes  Cisco 800 Series Industrial Integrated Services Routers  Cisco IR800 Integrated Services Router Software Configuration Guide. Searching Cisco Documents To search an HTML document using a web browser, press Ctrl-F (Windows) or Cmd-F (Apple). In most browsers, the option to search whole words only, invoke case sensitivity, or search forward and backward is also available. To search a PDF document in Adobe Reader, use the basic Find toolbar (Ctrl-F) or the Full Reader Search window (Shift-Ctrl-F). Use the Find toolbar to find words or phrases within a specific document. Use the Full Reader Search window to search multiple PDF files simultaneously and to change case sensitivity and other options. Adobe Reader’s online help has more information about how to search PDF documents. Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.

Product Overview This chapter provides an overview of the features available for the Cisco IR829 Integrated Services Routers (ISRs) and contains the following sections:  General Description, page 11  SKU Information, page 18  Hardware Features, page 18  Antennas, page 20  Power Supply, page 34  SFP Modules, page 34 NOTE: For compliance and safety information, see Regulatory Compliance and Safety Information for Cisco 800 Series Routers. General Description The Cisco IR829 Integrated Services Router, part of the Cisco Integrated Services Routers Generation 2 (ISR G2) Family, is designed as a next generation ruggedized fixed form factor router. It is a a small-form factor cellular router targeting mobile/vehicle applications and includes WiFi to provide connectivity in non-carpeted IT spaces, Industrials, Utilities, Transportation, Infrastructure, Industrial M2M application, and asset monitoring. The IR829 comes in two models, single LTE modem and dual LTE modems. Figure 1 shows the IR829.

Figure 2 shows the front panel details of the Cisco IR829 Single Modem. Figure 2 Cisco IR829 Front Panel Single Modem Figure 3 shows the front panel details of the Cisco IR829 Dual Modem. 1 CELLULAR 0 AUX 5 Serial Ports 2 Limited Modularity Slot 6 USB 2.0 type-A Port 3 Gigabit WAN (SFP) 7 Power Input, Battery, and Ignition connector. Refer to the DC Power section for pin-outs. 4 Gigabit Ethernet LAN/PoE (RJ45) 8 WLAN ANT 0 2.4GHz

Figure 4 shows the back panels details of the Cisco IR829 Single Modem. Figure 4 Cisco IR829 Back Panel Single Modem Figure 5 shows the back panels details of the Cisco IR829 Dual Modem. 1 CELLULAR 0 AUX 5 Serial Ports 2 Limited Modularity Slot 6 USB 2.0 type-A Port 3 Gigabit WAN (SFP) 7 Power Input, Battery, and Ignition connector. Refer to the DC Power section for pin-outs. 4 Gigabit Ethernet LAN/PoE (RJ45) 8 WLAN ANT 0 2.4/5GHz 1 WLAN ANT 0 5GHz 5 Denotes SIM card order, SIM0 on top and SIM1 on bottom. 2 WLAN ANT 1 2.4GHz 6 WLAN ANT 1 5GHz 3 Cover over SIM cards, reset button and console port cover, see Figure 6 7 CELLULAR 0 MAIN 4 GPS SMA

NOTE: Behind the SIM Door Assembly, there is a reset switch(1), Mini USB console port(2), and Dual SIM slots(3). See Figure 6 for details Figure 6 Behind the SIM Door Figure 7 shows the top of the Cisco IR829. 1 Cellular 1 Main 5 Denotes SIM card order, SIM0 on top and SIM1 on bottom. 2 WLAN ANT 1 2.4/5GHz 6 Cellular 1 AUX 3 Cover over SIM cards, reset button and console port cover, see Figure 6 7 CELLULAR 0 MAIN 4 GPS SMA

Figure 8 shows the LED detail from the Dual Modem SKU. Single Modem SKUs will only have Cellular 0 LEDs. Figure 8 Cisco IR829 LED Detail The following section shows a detailed description of the LEDs. LEDs Table 1 describes the LEDs for the Cisco IR829.

Green Steady on — Normal operation Green Flashing — Boot up phase or in ROM Monitor mode Amber Steady on — System shutdown due to under or over voltage conditions Amber Flashing — System has an error, but has network connectivity POE POE Power Supply Status Off — No -54V PoE power supply detected or no PoE board installed Green Steady on — 54V POE power supply good and all powered port operating normally Amber Steady on — 54V POE power supply good, but one or more POE ports has a fault. VPN VPN Off — No VPN tunnel Steady on — At least one VPN tunnel is up GE0 WAN Link Status Off — No link Steady on — Link is up Flashing — Transmitting and Receiving data GPS GPS Status Off — GPS not configured On — GPS configured Slow Flash — GPS Acquiring in Standalone GPS Fast Flash — GPS Acquiring in Assisted GPS Slow Flash is defined as the LED will be on for 0.25 seconds and off for 0.75 seconds. Fast Flash s defined as the LED will be on for 0.25 seconds and off for 0.25 seconds. MOD Ethernet LAN Switch Ports GE1-GE4] Single LED per Port Link Status/POE Status Off — No link Green Steady on — Link is up Green Flash — Transmitting and Receiving data Amber — POE Fault, implies no link

contains the ROMMON boot code. All memory components are factory default and not upgradeable by the end user. Table 3 shows the memory allocation. Table 3 Cisco IR829 Memory WLAN 2.4GHz 5GHz Off — Radio is down (no SSID configured) Flashing Green — Bootloader, IOS Ethernet Initialization, IOS Start Up after system initialization. Green to Red to Amber — Discovery/Join process. Rapid Flashing Green — Joined to a controller Steady Green — One wireless client is associated. CELLULAR0/ CELLULAR1 ACT Off — Module not powered on On — Module is powered on and connected but not transmitting or receiving Slow Flash — Module is powered on and searching for connection Fast Flash — Module is transmitting or receiving. CELLULAR0/ CELLULAR1 RSSI The RSSI LEDs are a 3 LED bar graph to indicate signal strength. Their functionality is described in the RSSI LED figure below. SIM0/SIM1 Sim cards Off — No USIM Green — USIM installed and active Table 1 LED Descriptions (continued) LED Activity Description RSSI RSSI (2) RSSI (1) RSSI (0) Green Green Green/Amber < -110dBm Off Off Off -110 to -90dBm Off Off On - Amber -90 to -75dBm Off Off On - Green -75 to -60dBm Off On - Green On - Green > -60dBm On - Green On - Green On - Green Memory Capacity DDR 2GB Boot ROM 16MB System Flash 4GB

Hardware Features This section provides an overview of the following hardware features for the Cisco IR829.  Platform Features for Cisco IR829, page 18  Antennas, page 20  Reset Button, page 19  Supported Cisco Antennas and Cables, page 22  Power Supply, page 34 Platform Features for Cisco IR829 The following lists the hardware platform features for the Cisco IR829.  Intel Atom Dual-Core Rangeley CPU, 1250 MHz Table 4 Supported SKUs for Cisco IR829s SKU ID Description IR829GW-LTE-NA-AK9 Multimode Cisco LTE 2.0 for carriers operating in LTE 700 MHz (band 17), 1900 MHz (band 2 PCS), or 1700/2100 MHz (band 4 AWS) frequencies; backward-compatible with UMTS and HSPA+: 850 MHz (band 5), 900 MHz (band 8), 1900 MHz (band 2 PCS), and 1700/2100 MHz (band 4 AWS). IR829GW-LTE-VZ-AK9 Multimode Cisco LTE 2.0 for carriers operating in LTE 700 MHz (band 13), 1700/2100 MHz (band 4 AWS), or 1900 MHz (band 25 extended PCS) frequencies; backward-compatible with EVDO Rev A/CDMA 1x BC0, BC1, BC10. IR829GW-LTE-GA-EK9, IR829GW-LTE-GA-ZK9, IR829GW-LTE-GA-CK9 and IR829GW-LTE-GA-SK9 Multimode Cisco LTE 2.0 for carriers operating in LTE 800 MHz (band 20), 900 MHz (band 8), 1800 MHz (band 3), 2100 MHz (band 1), or 2600 MHz (band 7) frequencies; backward-compatible with UMTS and HSPA+: 850 MHz (band 5), 900 MHz (band 8),1900 MHz (band 2), and 2100 MHz (band 1). Second Generation SKU ID NOTE: These SKUs will be phased in throughout the 2017 calendar year. Check with your marketing contact for more information on availability. IR829-2LTE-EA-AK9 Dual Modem LTE for Canada IR829-2LTE-EA-BK9 Dual Modem LTE for USA IR829-2LTE-EA-EK9 Dual Modem LTE for Europe IR829GW-LTE-LA-QK9 Single Modem LTE for Japan IR829GW-LTE-LA-DK9 Single Modem LTE for India IR829GW-LTE-LA-ZK9 Single Modem LTE for Australia/New Zealand IR829GW-LTE-LA-KK9 Single Modem LTE for Korea IR829GW-LTE-LA-SK9 Single Modem LTE for Hong Kong IR829GW-LTE-LA-NK9 Single Modem LTE for Panama

 64MB SPI BIOS NOR flash  8GB (4GB usable) “eMMC” bulk storage flash  4-port GE LAN switch, optional PoE 802.3at (30W max) for Cisco devices only. NOTE: The software does not support PoE negotiation over LLDP, only CDP. Therefore, PoE will only power up Cisco devices,  WAN 1 GE SFP  WWAN /WLAN — mini PCIe slots for 3G/4G/LTE modems, dual SIM — Single 802.11 a/b/g/n WiFi radio with MIMO support.  Optional Limited Modularity (BYOI) slot  One RJ45 RS232 DTE serial port  One RJ45 RS232 DCE/RS485 serial port  One USB 2.0 Type A external port  One mini USB type B connector for console  Lithium Ion battery backed-up RTC  External Reset/Recovery Push Button  External Power — Direct-wire 12/24VDC vehicle charging system input (9 — 32VDC) — 4-pin locking power connector  External GPS SMA Connector  Six External TNC/RP-TNC connectors (depends on the configuration) for connection to WWAN /WLAN internal modules  Class A EMC compliance  RoHS6 compliance  Mechanical — Fanless operation — Form-factor with no cable cover = 11.00” x 7.70” x 1.73” (WDH) — Horizontal, Vertical, wall, floor, cabinet-mount and shelf-mount Reset Button The Reset button resets the router configuration to the default configuration set by the factory. To restore the router configuration to the default configuration set by the factory, use a standard size #1 paper clip with wire gauge 0.033 inch or smaller and simultaneously press the reset button while applying power to the router. NOTE: The rear cover must be removed to expose the reset switch. See Figure 6 on page -14 for details.

Software Configuration Guide. The IR829 differs from traditional IOS routers. Antennas The IR829 has RP-TNC connectors for Wi-Fi and TNC connectors for cellular. The IR829 also has an SMA connector for a GPS antenna. Standard antennas are:  Two multiband swivel-mount dipole antennae (ANT-4G-DP-IN-TNC) and one extender (4G-AE010-R).  WLAN: Three Cisco Multiband Swivel-Mount Dipole Antennae. (AIR-ANTM2050D-R) for WLAN functionality. For detailed information about Cisco Antennas, please refer to the following guides: Cisco Industrial Routers Antenna Guide: http://www.cisco.com/c/en/us/td/docs/routers/connectedgrid/antennas/installing-combined/industrial-routers-antenna-guide.html Cisco Aironet Antennas and Accessories Reference Guide http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-antennas-accessories/product_data_sheet09186a008008883b.html Antennas and Installation Scenarios NOTE: Before choosing your antenna type and installation scenario, read through the following information. Coexistence of radio standards: When operating and planning installation of products with WiFi, 4G LTE, and GPS wireless standards coexisting on the IR829 platform, the user needs to provision greater than 15dB isolation between the WiFi and LTE antennas at all frequencies of 4G LTE and WiFI operation for minimum impact to performance. Ideally, isolation should be 20-25dB or more. Specifically, users should not install 4G LTE dipoles and WiFi dipoles on the chassis at the same time, since doing so would generally result in less than 15dB isolation and may have a strong impact on performance depending on frequency bands in question. Vehicular 5-in-1 and 2-in-1 installation and deployment notes In the section that follows, the 5-in-1 antenna refers to ANT-5-4G2WL2G1-O, and 2-in-1 antenna refers to ANT-2-WLAN-D-O.

flat mounting surface with a mounting hole for the 2-in-1 WiFi antenna. Without a flat mounting surface, the antenna will not meet IP67 standards and may have reduced service life. Ground plane Cisco recommends having a 1 foot ground plane under both the 5-in-1 and 2-in-1 antennas. In case of a metal vehicle roof, the roof itself shall be the ground plane. While Cisco has investigated the effects of ground plane and no ground plane, wireless performance was certified with the 1 foot ground plane. Isolation between 5-in-1 and 2-in-1 antennas Cisco recommends 18" inch spacing between the 5-in-1 and the 2-in-1 antenna centers for optimal isolation. Cisco recommends routing the 2.4GHz WLAN ports of the IR829 to the 2-in-1 antenna, and the 5GHz ports to the 5-in-1 antenna to optimize isolation between WiFi 2.4 GHz and cellular 4G LTE. The 5-in-1 antenna has been fully optimized for WiFI and cellular LTE coexistence and isolation. Connecting the 2.4GHz WiFi signals to a separate antenna simply allows to user to optimize the antenna isolation further. Both the 5-in-1 and 2-in-1 are dual band WiFi capable and fully support both 2.4 GHz or 5GHz WLAN signals. MIMO ports on 5-in-1 and 2-in-1 Cellular and WLAN ports on the 5-in-1 and 2-in-1 antennas support MIMO technology. MIMO brings significant improvements in throughput and robustness of the wireless link in fading channels. Users choosing to connect only one wireless port on MIMO capable products are giving up significant wireless performance in both throughput and robustness of the link.  The individual 4G antenna cables on the 5-in-1 antenna can be connected to either cellular port of IR829. There is no one-to-one assignment requirement.  The individual WLAN antenna cables on the 5-in-1 antenna and the 2-in-1 antenna can be connected to any WLAN port of IR829. There is no one to one assignment requirement.

The following section shows some examples of different installation scenarios. Modem Support The Cisco IR800 series Industrial routers use the MC73XX and MC74XX series modems. The software download page can be found here: https://software.cisco.com/download/navigator.html?mdfid=286288566&flowid=76082 NOTE: Be sure to select the correct firmware download for your carrier. The Cisco Firmware Upgrade Guide for Cellular Modems can be found here: http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/firmware/Firmware_Upgrade.html Previous versions of this guide contained additional configuration information which has now been relocated to the Cisco IR800 Integrated Services Router Software Configuration Guide. Supported Cisco Antennas and Cables 4G/LTE Radio Cables/Antennas 4G/LTE Radio Cables/Antennas Use Case 1 Table 5 4G/LTE Radio Cables/Antennas Use Case 1 Item Description Antenna Arrangement 1' 2', 5', 10', 15' or 20' cable to mast mounted antenna, Stick Omni or Directional Flat Panel antenna Internal Cable None, router located in outdoor protective enclosure Adapter and/or Lightning Arrestor None External Cable RA-TNC(m) to N(m), LMR-400-DB, 20', qty 2  "CAB-L400-20-TNC-N Antenna 2x 4G Omni Stick, Standard Perf, 10” 2dBi, 1x N(f) each  ANT-4G-OMNI-OUT-N 1x 4G Panel Antenna, 2x N(f) each  ANT-4G-PNL-OUT-N

4G/LTE Radio Cables/Antennas Use Case 2 4G/LTE Radio Cables/Antennas Use Case 3 Table 6 4G/LTE Radio Cables/Antennas Use Case 2 Item Description Antenna Arrangement 1' 2', 5', 10', 15' or 20' cable to mast mounted antenna, Stick Omni or Directional Flat Panel antenna Internal Cable R/A-TNC(m) to N(m), LMR-240-FR/CMR, 2’, qty 2 R/A-TNC(m) to N(m), LMR-240-FR/CMR, 1', qty 2 R/A-TNC(m) to N(m), LMR-240-FR/CMR, 5', qty 2 R/A-TNC(m) to N(m), LMR-240-FR/CMR, 10', qty 2 R/A-TNC(m) to N(m), LMR-240-FR/CMR, 15', qty 2 R/A-TNC(m) to N(m), LMR-240-FR/CMR, 20', qty 2 Note These cables not available from Cisco Adapter and/or Lightning Arrestor None External Cable None Antenna 1x 4G Panel Antenna, 2x N(f) each  ANT-4G-PNL-OUT-N Table 7 4G/LTE Radio Cables/Antennas Use Case 3 Item Description Antenna Arrangement Front Panel Swivel Mount 4G-LTE dipoles Internal Cable Chose one of 3 scenarios:  None  Quantity of 2 — PID: 4G-AE010-R — 10ft extension base for TNC dipole antennas  Quantity of 2 — PID: 4G-AE015-R — 15ft extension base for TNC dipole antennas

Adapter and/or Lightning Arrestor None External Cable None Antenna Quantity of 2 4G Indoor Swivel Mount Dipole, 0 dBi, TNC(m), white  ANT-4G-DP-IN-TNC Table 7 4G/LTE Radio Cables/Antennas Use Case 3 Item Description

4G/LTE Radio Cables/Antennas Use Case 4 4G/LTE Radio Cables/Antennas Use Case 5 4G/LTE Radio Cables/Antennas GPS Use Case 1 Table 8 4G/LTE Radio Cables/Antennas Use Case 4 Item Description Antenna Arrangement Front Panel Swivel Mount 4G-LTE dipoles Internal Cable Chose one of 3 scenarios:  None  Quantity of 2 — PID: 4G-AE010-R — 10ft extension base for TNC dipole antennas  Quantity of 2 — PID: 4G-AE015-R — 15ft extension base for TNC dipole antennas Adapter and/or Lightning Arrestor None External Cable None Antenna Quantity of 2 4G Indoor Swivel Mount Dipole, 0 dBi, TNC(m), black  4G-LTE-ANTM-D Table 9 4G/LTE Radio Cables/Antennas Use Case 5 Item Description Antenna Arrangement 2x ceiling mount 4G-LTE antennas Internal Cable None Adapter and/or Lightning Arrestor None External Cable None Antenna Quantity of 2 4G Indoor omni-directional Ceiling Mount 2 dBi,  4G-ANTM-OM-CM Quantity of 2 4G Dipole Ceiling Mount 2 dBi  ANT-4G-DP-IP-TNC

Single Band Cisco WiFi Antenna Supported Single Band Cisco WiFi Antenna Use Case 1 Table 10 4G/LTE Radio Cables/Antennas GPS Use Case 1 Item Description Antenna Arrangement GPS Antenna with Integrated 15' coax cable, Mounted to top of Utility Cabinet Roof SMA(f), qty 1 Internal Cable None Adapter and/or Lightning Arrestor None External Cable None Antenna GPS Antenna Need one with integrated coax cable and SMA(m) connector, 17ft, outdoor, IP67 Quantity of 1  GPS-ACT-ANTM-SMA= Table 11 Single Band Cisco WiFi Antenna Use Case 1 Item Description Antenna Arrangement Single Band, Front Panel Mounted Antennas Radio Module Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors: 4x RP-TNC (jack) Adapter and/or Lightning Arrestor N/A Internal Cable N/A External Cable N/A Antenna 2x Single Band, Swivel Mount Omni, RP-TNC(plug), 2.2dBi @ 2.4 GHz  AIR-ANT4941 2x Single Band, Swivel Mount Omni, RP-TNC(plug), 3.5dBi @ 5 GHz  AIR-ANT5135

Supported Single Band Cisco WiFi Antenna Use Case 2 Supported Single Band Cisco WiFi Antenna Use Case 3 Table 12 Single Band Cisco WiFi Antenna Use Case 2 Item Description Antenna Arrangement Single Band, Single Element, Ceiling Mounted Antennas Radio Module Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors: 4x RP-TNC (jack) Adapter and/or Lightning Arrestor N/A Internal Cable Choose one of 2:  None  RP-TNC (jack) to RP-TNC (plug), Outdoor rated, Plenum rated, 0.195" O.D. cable, 5' long — AIR-CAB005PL-R External Cable N/A Antenna 2x Single Band, Ceiling Mount Omni, 36” LONG RG-58 cable with RP-TNC (plug), 5.2dBi @ 2.4 GHz  AIR-ANT1728 2x Single Band, Ceiling Mount Omni, 36" LONG RG-58 cable with RP-TNC (plug), 5.2dBi @ 5 GHz  AIR-ANT5160V-R Table 13 Single Band Cisco WiFi Antenna Use Case 3 Item Description Antenna Arrangement 2.4 GHz, Dual Element, 5 GHz Single Element, Ceiling Mounted Antennas Radio Module Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors: 4x RP-TNC (jack) Adapter and/or Lightning Arrestor N/A

Supported Single Band Cisco WiFi Antenna Use Case 4 Internal Cable Choose one of 2:  None  RP-TNC(jack) to RP-TNC(plug), Outdoor rated, Plenum rated, 0.195” O.D. cable, 5’ long — AIR-CAB005PL-R External Cable N/A Antenna 1x Single Band, Ceiling Mount Omni, Dual Element, 36" LONG RG-58 cable with RP-TNC, 2.0dBi @ 2.4 GHz  AIR-ANT24020V-R 2x Single Band, Ceiling Mount Omni, 36" LONG RG-58 cable with RP-TNC (plug), 5.2dBi @ 5 GHz  AIR-ANT5160V-R Table 13 Single Band Cisco WiFi Antenna Use Case 3 Item Description Table 14 Single Band Cisco WiFi Antenna Use Case 4 Item Description Antenna Arrangement Single Band, Dual Element, Wall Mounted Antennas Radio Module Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors: 4x RP-TNC (jack) Adapter and/or Lightning Arrestor None, or: RP-TNC lightning arrestor, qty 4  AIR-ACC245LA-R

Supported Single Band Cisco WiFi Antenna Use Case 5 Internal Cable None External Cable Choose one of 4:  None  RP-TNC(plug) to RP-TNC(jack) LMR-400-DB, 5' qty 4 — AIR-CAB005LL-R  RP-TNC(plug) to RP-TNC(jack) LMR-400-DB, 20' qty 4 — AIR-CAB020LL-R  RP-TNC(plug) to RP-TNC(jack) LMR-400-DB, 50' qty 4 — AIR-CAB050LL-R  RP-TNC(plug) to RP-TNC(jack) LMR-600-DB, 100' qty 4 — AIR-CAB100ULL-R Antenna 1x Single Band, Dual Element, Wall Mount Patch, 18" LONG RG-58 cable with RP-TNC, 6.5dBi @ 2.4 GHz  AIR-ANT2465P-R 1x Single Band, Dual Element, Wall Mount Omni, 18" LONG RG-58 cables with RP-TNC, 4.5dBi @ 5 GHz (INDOOR ONLY)  AIR-ANT5145V-R — OR 1x Single Band, Dual Element, Wall Mount Patch, 18" LONG RG-58 cables with RP-TNC, 7.0dBi @ 5 GHz (INDOOR/OUTDOOR)  AIR-ANT5170P-R Table 14 Single Band Cisco WiFi Antenna Use Case 4 Item Description Table 15 Single Band Cisco WiFi Antenna Use Case 5 Item Description Antenna Arrangement Single Band, Dual Element, Wall Mounted Patch, Indoor/ Outdoor Antennas Radio Module Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors: 4x RP-TNC (jack) Adapter and/or Lightning Arrestor N(f) to N(f), RF-adapter, qty 4  AIR-ACC370-NF-NF

Dual Band Cisco WiFi Antenna Supported Dual Band Cisco WiFi Antenna Use Case 1 Table 16 Dual Band Cisco WiFi Antenna Use Case 1 Supported Dual Band Cisco WiFi Antenna Use Case 2 Internal Cable None External Cable RP-TNC(plug) to N(m)-R/A, LMR-240-DB, 5', qty 4  AIR-CAB005LL-R-N Antenna 1x Single Band, Dual Element, Wall Mount Patch, 18" LONG RG-58 cable with N(m), 13dBi @ 2.4 GHz  AIR-ANT2413P2M-N 1x Single Band, Dual Element, Wall Mount Patch, 18" LONG RG-58 cable with N(m), 14dBi @ 5 GHz  AIR-ANT5114P2M-N Table 15 Single Band Cisco WiFi Antenna Use Case 5 Item Description Item Description Antenna Arrangement Dual Band Front Panel Mounted Antennas Radio Module Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors: 4x RP-TNC (jack) Adapter and/or Lightning Arrestor N/A Internal Cable N/A External Cable N/A Antenna 2x Dual Band, Swivel Mount Omni, RP-TNC(plug), 2dBi @ 2.4 GHz, 4dBi @ 5 GHz  AIR-ANT2524DB-R Table 17 Dual Band Cisco WiFi Antenna Use Case 2 Item Description Antenna Arrangement Dual Band Front Panel Mounted Antennas Radio Module Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors: 2x RP-TNC (jack) Adapter and/or Lightning Arrestor N/A

Supported Dual Band Cisco WiFi Antenna Use Case 3 7 in 1 Antenna Configuration for Transportation Transportation Use Case 1 Antenna Arrangement 7 x RF ports, with the IR829 deployed in a transportation application. (Default Configuration) Quinta 5-in-1 antenna AND a WiFi 2-in-1 antenna to utilize all 7 ports. The 5-in1 Quinta antenna and the 2-in1 WiFi antennas need to be separated 18" between mounting hole centers of the two antennas. Extension Cable No extension cables are required if the IR829 is located within ~1.0ft of 5-in-1 antenna, and ~2.0ft of WiFi 2-in-1 antenna. If these conditions are not met, this deployment requires the following extension cables: Cellular extension cables (2 ports) Internal Cable N/A External Cable N/A Antenna 1x Dual Band, Dual Element per Band, Omni, 18" LONG RG-58 cables with RP-TNC (plug), 2.0dBi @ 2.4 GHz (2 ports), 3.0dBi @ 5 GHz (2 ports)  AIR-ANT2451V-R Table 17 Dual Band Cisco WiFi Antenna Use Case 2 Item Description Table 18 Dual Band Cisco WiFi Antenna Use Case 3 Item Description Antenna Arrangement Dual Band Front Panel Mounted Antennas Radio Module Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors: 2x RP-TNC (jack) Adapter and/or Lightning Arrestor N(f) to N(f), RF-adapter, qty 2  AIR-ACC370-NF-NF Internal Cable N/A External Cable RP-TNC(plug) to N(m)-R/A, LMR-240-DB, 5', qty 2  AIR-CAB005LL-R-N Antenna 2x Dual Band, Swivel Mount Omni, RP-TNC(plug), 2dBi @ 2.4 GHz, 4dBi @ 5 GHz  AIR-ANT2524DB-R

Qty 2X LMR-400-DB TNC(m)-R/A - TNC(f), 5ft  4G-CAB-LMR400-5 — OR Qty 2X LMR-400-DB TNC(m)-R/A - TNC(f), 10ft  G-CAB-LMR400-10 — OR Qty 2X LMR-400-LLPL plenum / indoor only TNC(m)-R/A - TNC(f), 20ft  4G-CAB-ULL-20 WiFi 2.4 GHz / 5GHz extension cables (4 ports, can mix and match lengths per installation requirements if needed) Qty 4x LMR-400-DB RPTNC(plug) - STR RPTNC(jack) - STR, 5ft  AIR-CAB005LL-R — OR Qty 4x LMR-400-DB RPTNC(plug)-R/A RPTNC(jack)-STR, 10ft  CAB-L400-10-R — OR Qty 4x LMR-400-DB RPTNC(plug)-STR RPTNC(jack)-STR, 20ft  AIR-CAB020LL-R — AND GPS port No extension cable required, 5-in-1 antenna comes with integrated active GPS antenna with 17ft cable. Antenna Quinta 5 element 5-in-1 transportation antenna, black radome color, 2x 4G cellular, 2x dual band WiFi, 1xGPS  ANT-5-4G2WL2G1-O  07-100261-01 Has the following integrated cables: qty 2 x cellular, LMR-195, 2ft long, TNC(m) qty 2 x WiFi, 2ft long, LMR-195 RPTNC (plug) qty 1 x GPS, RG-174, 17ft long, SMA(m) — AND WiFi 2-in-1 2 element 2 in 1 transportation antenna, black radome color, 2x dual band WiFi  ANT-2-WLAN-D-O Has the following integrated cables: qty 2 x WiFi, 3ft long, LMR-240 RPTNC (plug)

Transportation Use Case 2 Antenna Arrangement 7 x RF ports, with the IR829 deployed in a transportation application. (Alternate Configuration, can be used in case the application calls for the WiFi antennas to be separate from the LTE antenna for example. a ceiling mount WLAN). This case describes a Tercia 3-in-1 transportation antenna (which covers MIMO cellular and GPS) together with qty 2 x 2-in-1 WiFi antennas. NOTE: A custom ceiling mount bracket is required for the 2-in-1 antenna if installed in a ceiling mount configuration (NOT SUPPLIED BY CISCO) Extension Cable No extension cables are required if the IR829 is located within ~1.0ft of 5-in-1 antenna, and ~2.0ft of WiFi 2-in-1 antenna. If these conditions are not met, this deployment requires the following extension cables: Cellular extension cables (2 ports) Qty 2X LMR-400-DB TNC(m)-R/A - TNC(f), 5ft  4G-CAB-LMR400-5 — OR Qty 2X LMR-400-DB TNC(m)-R/A - TNC(f), 10ft  G-CAB-LMR400-10 — OR Qty 2X LMR-400-LLPL plenum / indoor only TNC(m)-R/A - TNC(f), 20ft  4G-CAB-ULL-20 WiFi 2.4 GHz / 5GHz extension cables (4 ports, can mix and match lengths per installation requirements if needed) Qty 4x LMR-400-DB RPTNC(plug) - STR RPTNC(jack) - STR, 5ft  AIR-CAB005LL-R — OR Qty 4x LMR-400-DB RPTNC(plug)-R/A RPTNC(jack)-STR, 10ft  CAB-L400-10-R — AND GPS port - No extension cable required, 3-in-1 antenna comes with integrated active GPS antenna with 17ft cable. Antenna Quinta 5 element 5-in-1 transportation antenna, black radome color, 2x 4G cellular, 2x dual band WiFi, 1xGPS  ANT-5-4G2WL2G1-O Has the following integrated cables:

 qty 2 x WiFi, 2ft long, LMR-195 RPTNC (plug)  qty 1 x GPS, RG-174, 17ft long, SMA(m) — AND WiFi 2-in-1 2 element 2 in 1 transportation antenna, black radome color, 2x dual band WiFi  ANT-2-WLAN-D-O Has the following integrated cables:  qty 2 x WiFi, 3ft long, LMR-240 RPTNC (plug) Power Supply The Cisco IR829 comes with an external power connector.  Direct-wire 12/24VDC vehicle charging system input (9 — 32VDC).  4-pin locking Molex power connector, Cisco part number 29-2562-01. There is an external AC to DC power adapter for the IR829. It meets ITE standards and operating temperature range of -20C to 60C, but is not suited for industrial environment. Part Number is IR829-PWR125W-AC. There is a 12.5 feet power cable available to order. Part Number is IR829-DC-PWRCORD. SFP Modules The router Ethernet SFP modules provide connections to other devices. These field-replaceable transceiver modules provide the uplink interfaces. Local connectors (LCs) provide the fiber-optic connection. RJ-45 connectors allow copper connections. You can use any combination of the supported SFP modules listed in the table that follows.

on the SFP installed. Since there is no I-temp copper SFP available in the market, there is no Copper SFP supported. In order to use a Copper SFP, you must enter service internal mode, and enter “unsupported transceivers”. Then unplug and insert the Copper SFP again. NOTE: Speed and duplex commands are not available on the GE0 WAN interface. The following two Copper SFPs (non I-temp) will be officially supported at 1Gbps:  Copper SFP - GLC- T — Copper 1Gbps, (0 to 70°C), CPN is 30-1410-04 Table 19 Maximum Operating Temperature Type of SFP Module Model Rugged and Industrial SFPs –40 to 185°F (–40 to 85°C) GLC-SX-MM-RGD with digital optical monitoring (DOM) support GLC-LX-SM-RGD with digital optical monitoring (DOM) support GLC-ZX-SM-RGD with digital optical monitoring (DOM) support Commercial SFPs 32° to 158°F (0° to 70°C) GLC-SX-MM GLC-LH-SM GLC-BX-U, with Digital Optical Monitoring (DOM) support GLC-BX-D, with Digital Optical Monitoring (DOM) support CWDM-SFP, with Digital Optical Monitoring (DOM) support DWDM-SFP, with Digital Optical Monitoring (DOM) support Extended Temperature SFP 23° to 185°F (-5° to 85°C) SFP-GE-S, with Digital Optical Monitoring (DOM) support SFP-GE-L, with Digital Optical Monitoring (DOM) support SFP-GE-Z, with Digital Optical Monitoring (DOM) support GLC-SX-SMD GLC-LH-SMD GLC-EX-SMD GLC-TE GLC-FE-100LX-RGD GLC-FE-100FX-RGD Copper SFP Supported on IOS 15.6(3)M but GE only GLC- T (0 to 70°C) SFP-GE-T (-5 to 85°C)

— Copper 1Gbps, (-5 to 85°C), CPN is 30-1421-02 Additional SFPs with added support are:  GLC-FE-100LX-RGD — Fiber (fixed speed of 100Mbps)  GLC-FE-100FX-RGD — Fiber (fixed speed of 100Mbps)  GLC-TE — Copper (fixed speed of 1Gbps)  GLC-FE-T= — Copper 100Mbps NOTE: Auto negotiation is not supported on these SFPs. For minimum software requirements, refer to the Release Notes for your platform. For the most up-to-date list of supported SFP models for Cisco Industrial Ethernet switches, see http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6981.html#wp138176 RJ45 Ports Two RJ45 serial ports are provided to control and monitor RS232 or RS485 equipment. Serial port 0 can be configured for either RS232 DCE or RS485. Serial port 1 can be configured for RS232 DTE only. The RJ45 pinouts are shown in Figure 9 Figure 9 RJ45 pinouts RS232 Port The RS232 DTE/DCE pin out applies to both serial 0 and serial 1. The pinout/signal difference between serial 0 and serial 1 is the direction of the data and flow control signals. The RS232-DCE port is designed to be connected to a far-end DTE port, or to another DCE port via a crossover (null-modem) cable. The RS232-DTE port is designed to be connected to a far-end DCE port, or to another DTE port via a crossover (null-modem) cable. This port is not shared with the Console port. Note that the RS232 DTE pin out is different from the Console/Auxiliary port.

3,6 were chosen for RS485 so that an Ethernet CAT-5 with these standard twisted-pair pin assignments can be used. Figure Figure 10 shows the characteristics of the S0 and S1 ports. Figure 10 S0 and S1 Characteristics

Installing the Router This chapter describes the equipment and the procedures for successfully installing the Cisco IR829 and contains the following sections:  Equipment, Tools, and Connections, page 39  Installing the Router, page 40 CAUTION: Do not place anything on top of the router that weighs more than 10 pounds (4.5 kilograms), and do not stack routers on a desktop. Excessive weight on top of the router could damage the chassis. CAUTION: Do not install the router or power supplies next to a heat source of any kind, including heating vents. WARNING: Read the installation instructions before connecting the system to the power source. Statement 1004 WARNING: Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 WARNING: No user-serviceable parts inside. Do not open. Statement 1073 WARNING: Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 WARNING: Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54). Statement 1052 WARNING: This product is not intended to be directly connected to the Cable Distribution System. Additional regulatory compliance and legal requirements may apply for direct connection to the Cable Distribution System. This product may connect to the Cable Distribution System ONLY through a device that is approved for direct connection. Statement 1078 Equipment, Tools, and Connections This section describes the equipment, tools, and connections necessary for installing your Cisco IR829. It contains the following topics:  Items Shipped with your Router, page 40  Additional Items, page 40  Ethernet Devices, page 40

Installing the Router Items Shipped with your Router Unpack the box and verify that all items listed on the invoice were shipped with the Cisco IR829. The following items are shipped with your router:  Getting Started Guide Part Number 78-100611  Power Cable components  Grounding Lug  Ethernet Cable Part Number 75-1501-01 Additional Items The following items are not shipped with the router but are required for installation:  ESD-preventive cord and wrist strap.  Screws for mounting the router on a wall.  Two number-10 wood screws (round- or pan-head) with number-10 washers or two number-10 washer-head screws, for mounting on a wall stud. The screws must be long enough to penetrate at least 3/4 inch (20 mm) into the supporting wood or metal wall stud.  Two number-10 wall anchors with washers, for mounting the router on a hollow wall.  Wire crimper for chassis grounding.  Wire for connecting the chassis to an earth ground.  AWG 14 (2 mm2) or larger wire for NEC-compliant chassis grounding.  AWG 18 (1 mm2) or larger wire for EN/IEC 60950–compliant chassis grounding.  Ethernet cables for connecting to the Fast Ethernet (FE) WAN and LAN ports.  Ratcheting torque flathead screwdriver that exerts up to 15 in-lb (1.69 N-m) of pressure.  A number-2 Phillips screwdriver. Ethernet Devices Identify the Ethernet devices that you will connect to the router: hub, servers, and workstations or PCs. Ensure that each device has a network interface card (NIC) for connecting to Ethernet ports. If you plan to configure the software using Cisco IOS commands through the console port, provide an ASCII terminal or a PC that is running terminal emulation software to connect to the console port. Installing the Router This section describes how to install the Cisco IR829. This router can be installed on a table top or other flat horizontal surface mounted on a wall or DIN rail. The recommended clearance when horizontally mounted is 1.5 inches on both sides for floor mount bracket clearance and 2 inches on top. Top clearance is not required but stacking heat-dissipating objects on top of the router is not allowed. I/O side clearance is needed as it is required to access the cable connections. Clearance is not required on the backside (opposite side from I/O face) unless DIN rail mounting is required. Clearance is required to attach and mount the DIN rail bracket. The same clearances apply when mounted vertically.

Installing the Router This section also describes how to attach external antennas to the routers and contains the following topics:  Warnings, page 41  Accessing the SIM Cards, page 41  Installing Antennas, page 42  Mounting on a Wall, Table, or Other Flat Surface, page 43  Installing the Router Ground Connection, page 44 Warnings WARNING: This equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to connect the host to earth ground during normal use. Statement 242 Accessing the SIM Cards The SIM cards are high reliability, and cellular multihoming support for dual SIM card socket; compliant with ISO-7816-2 (SIM mechanical). Their size is 0.98425 in (25 mm) X 0.59055 in (15 mm). This section describes how to install and/or replace a SIM card. Ensure that the router is not mounted to a wall, floor, or DIN rail. CAUTION: Do not touch any part of the exposed PCB circuit area when the SIM cover is removed. WARNING: The covers are an integral part of the safety design of the product. Do not operate the unit without the covers installed. Statement 1077 WARNING: Hot surface. Statement 1079 NOTE: High Temperature SIMs are required for 4G operations if the Ambient temperature is above 95F (35C) To access the SIM card in the Cisco IR829, follow these steps: 1. Place the router on its bottom and ensure that any installed antennas are carefully oriented. 2. Remove the SIM access panel using two Phillips head screws. (See Figure 1.) 3. Locate the SIM card you wish to install/replace. Details are shown in Figure 2. 4. Remove the SIM card (if present) and install the new card(s). — To install a card, slide it into the slot, and press it in until it clicks in place. The card is keyed so that you cannot insert it the wrong way. — To remove the card, push it in until it releases for it to pop out. Place it in an antistatic bag to protect it from static discharge.

Installing the Router Figure 1 Accessing the SIM Cards Figure 2 Sim Card Detail 5. Replace the panel and the screws. Installing Antennas NOTE: Before you install the Cisco IR829 Integrated Services Router on a table, wall, or DIN rail, install the antennas on the front panel. It is difficult to install the antennas after the router is installed. There are two TNC connectors on the front side of the chassis. There are four TNC and one SMA connectors on the back side of the chassis. Two TNC connectors are used to connect to the 4G modem. The four TNC connectors at the back will be connected to the two 4G modems. The front two TNC connectors will be used for WiFi. Orient the antennas. For optimum wireless performance, the antennas should be perpendicular with respect to the floor. If the router is being mounted on a desk, orient the antennas straight up. To attach the radio antennas to your wireless router, follow these steps: 1. Manually screw the antenna tight to the TNC connectors on the back of the router. 2. Orient the antennas. For optimum wireless performance, antennas should be generally perpendicular to each other. 1 Reset Button 2 Mini USB Port 3 Dual Sim Slots

Installing the Router Mounting on a Wall, Table, or Other Flat Surface The Cisco IR829 has mounting holes on the bottom of the chassis for mounting the unit on a wall or other vertical surface. The attachment hardware is provided. TIP: When choosing a location for wall-mounting the router, consider cable limitations and wall structure. WARNING: Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 378 To mount the router on a wall, follow these steps: 1. Locate the mounting holes on the router. There are 4 holes are shown in Figure 3. The mounting distance between the holes shown as #1 is 3.94 inches (10.0 cm), and the mounting distance between the holes shown as #2 is 10.64 inches (27.0 cm). Figure 3 Cisco IR829 Mounting Holes 2. Install the router to a wall stud using two number-10 wood screws, round- or pan-head, with number-10 washers or two number-10 washer-head screws. The screws must be long enough to penetrate at least 1.0 inch (25.4 mm) into the supporting wood or metal wall stud. (See Figure 4.)

Installing the Router Figure 4 Mounted to wall NOTE: For hollow-wall mounting, each bracket requires two wall anchors with washers. Wall anchors and washers must be size number 10. 3. Route the cables so that they do not put a strain on the connectors or mounting hardware. Cables should be routed down relative to the router to prevent water from traveling on the cables. Installing the Router Ground Connection The router must be connected to a reliable earth ground. Install the ground wire in accordance with local electrical safety standards.  For NEC-compliant grounding, use size 14 AWG (2 mm2) or larger copper wire and a ring terminal with an inner diameter of 1/4 in. (5 to 7 mm).  For EN/IEC 60950-compliant grounding, use size 18 AWG (1 mm2) or larger copper wire. WARNING: This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024 WARNING: This equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to connect the host to earth ground during normal use. Statement 242 To install the ground connection, follow these steps: 1. Locate the grounding lug attached to the back of the Cisco IR829. It will be attached underneath two screws. Remove the screws holding it to the router and set it aside for reuse. 2. Strip one end of the ground wire to the length required for the terminal. 3. Crimp the ground wire to the grounding lug using the wire crimper. 4. Attach the grounding lug to the chassis using the screws set aside in step 1. Tighten the screw to a torque of 8 to 10 inch-pound (0.9 to 1.1 newton meter). (See Figure 5.)

Installing the Router Figure 5 Chassis Ground Connection Points 5. Connect the other end of the ground wire to a known reliable earth ground point at your site. 6. If you are using this router in a vehicle, attach the ring terminal to the chassis using one of the screws provided and the green or green and yellow striped wire. Connect the other end of the wire to the vehicle ground. After you install and properly ground the router, you can connect the power wiring, the LAN cables, and the cables for administrative access as required for your installation.

This chapter describes how to connect Cisco IR829 Integrated Services Router (ISRs) to Ethernet devices and a network. The chapter contains the following sections:  Preparing to Connect the Router, page 47  Connecting a PC, Server, or Workstation, page 47  Connecting a Terminal or PC to the Console Port, page 48  Connecting to DC Power, page 49  Verifying Connections, page 51 Preparing to Connect the Router Before you connect the router to the devices, install the router according to the instructions in Chapter 3, “Installing the Router”. Preventing Damage to the Router To prevent damage to your router, follow these guidelines when connecting devices to your router:  Turn off power to the devices and to the router until all connections are completed. CAUTION: Do not turn on the devices until after you have completed all connections to the router. Connecting a PC, Server, or Workstation To connect a PC (or other Ethernet devices) to an Ethernet switch port, follow these steps: 1. Connect one end of the Ethernet cable to an Ethernet switch port on the router. In this example a PC is being connected to GE LAN Port 2. See Figure 1.

Connecting a Terminal or PC to the Console Port Figure 1 Connecting a Server, PC, or Workstation 2. Connect the other end of the cable to the RJ-45 port on the network interface card (NIC) that is installed in the PC, server, or workstation. 3. (Optional) Connect additional servers, PCs, or workstations to the other Ethernet switch ports. Connecting a Terminal or PC to the Console Port Connect a terminal or PC to the Console port either to configure the software by using the CLI or to troubleshoot problems with the router. To connect a terminal or PC to the console port on the router and access the CLI, follow these steps: 1. Connect the mini-USB side of a cable to the USB Console port on the router. Figure 2 shows the mini-USB location (1) for the Console port on the router. Figure 2 Connecting a Terminal or PC to the Console Port 2. Connect the opposite end of the mini-USB cable to the USB port on your laptop or PC. 3. To communicate with the router, wait for your laptop or PC to discover the new device. 4. If your laptop or PC warns you that you do not have the proper drivers to communicate with the router, you can obtain them from your computers manufacturer, or go here: https://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx 1 Ethernet cable 3 RJ-45 port on the PC, Server, or Workstation 2 Ethernet switch port on the router

Connecting to DC Power Connecting to DC Power WARNING: This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than 36 VDC, 5A Statement 1005 WARNING: This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. Statement 1045 Plugs and Pin-Outs The IR829 ships with a DC power accessory kit that contains a 4-pin locking connector and pins to use for the power connections. Four contacts are supplied, but only three are used. One is a spare. The Molex power connector is Cisco part number 29-2562-01. The power entry receptacle is on the IR829. The pin-outs are shown in Figure 3. Figure 3 Power Connector Pin-outs Table 1 Power connector Descriptions Constructing a Power cable Cisco provides a power cable that can be ordered under part number IR829-DC-PWRCORD. If you choose to construct your own power cable, use special care when making the connections for DC power. It is easy to make a mistake when crimping connections, and there is a very good tutorial available at Molex: http://www.molex.com/tnotes/crimp.html The specifications for the wiring are as follows:  16 AWG (1.02-to-1.29mm)  UL1015 Rated Table 4-2 Pin Number Name Description Color 1 DC In - DC Power Return (GND-) Black 2 Ignition Ignition Input (IGN) Blue 3 DC In + DC Power In (BAT+) Red 4 N/A N/A N/A

Connecting to DC Power  Wires will be wound at 1 twist per inch The example in Figure 4 shows a cable constructed with a ferrite for a different certification. You can build your cable without the ferrite eliminating items 2 and 3 in the diagram. Figure 4 Power cable Details listed in the power cable example are: Wiring the DC Power To connect the DC power on your Cisco IR829, follow these steps: Table 3 1 4-pin locking connector 2 2 loops of DC power and power return wires only. Other wires that may be used should run outside the Ferrite. Note Ferrite bead and the loops of wire are not needed at this time. 3 Ferrite Bead Note Ferrite bead and the loops of wire are not needed at this time. 4 Wires wound at 1 twist per inch 4 3 2 1 349790 1. Identify the DC power source and measure 4 strands of copper wire 16 AWG (1.29mm) long enough to connect to the DC power source. NOTE: The maximum length of the cable before twisting is 15 feet (4.6 meters). 2. Using an 16-gauge wire-stripping tool, strip each of the wires coming from each DC-input power source to 0.25 inch (6.3 mm) ± 0.02 inch (0.5 mm). Do not strip more than 0.27 inch (6.8 mm) of insulation from the wire. Stripping more than the recommended amount of wire can leave exposed wire from the power connector after installation. 333084

Verifying Connections Vehicle Connections When connecting to automotive power, it is expected that the ignition output will be +12 VDC. The DC In and DC Out leads can be directly connected to the battery, but it is recommended that they be connected after a fuse. NOTE: For details about the Ignition Power Management Software and setting it up, see the Cisco IR800 Integrated Services Router Software Configuration Guide. Verifying Connections To verify that all devices are properly connected to the router, first turn on all the connected devices, then check the LEDs. To verify router operation, refer to Table 4. For full LED description, see Chapter 2, “LEDs” 3. Using the pins included in the kit, crimp each pin onto a wire. 4. Insert the pins into the power connector, referring to previous figures for guidance. 5. Plug the connector into the power entry receptacle. Table 4 Verifying the Router Operation Power and Link LEDs to Check Normal Patterns PWR Green steady On Normal operation Green (flashing) Boot up phase or in ROM Monitor mode Amber System shutdown due to under or over voltage conditions GE0 WAN Steady On Link is up Flashing Transmitting and Receiving data Off No network activity.

Verifying Connections NOTE: There are single LTE and dual LTE SKUs available with the IR829. See Figure 8 on page -15 for details. Ethernet LAN Switch Ports Single LED per port Off — No link Green Steady on — Link is up Green Flash — Transmitting and Receiving data Amber — POE Fault, implies no link Sim cards SIM0/SIM1 Off — No USIM Green — USIM installed and active Cellular Modems CELLULAR0/ CELLULAR1 Off — Module not powered on On — Module is powered on and connected but not transmitting or receiving Slow Flash — Module is powered on and searching for connection Fast Flash — Module is transmitting or receiving. Table 4 Verifying the Router Operation (continued) Power and Link LEDs to Check Normal Patterns

Router (ISRs). NOTE: For compliance and safety information, see the Regulatory Compliance and Safety Information Roadmap that was shipped with the router and Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers. Router Specifications Table 1 lists the operational limits of the Cisco IR829. Operating the router outside of the limits specified is not supported. Table 1 Cisco IR829 Specifications Description Design Specification Physical Characteristics Dimensions (H x W x D) (height x width x depth) are 7.70 x 11 x 1.73 in. (19.6 x 27.9 x 4.39 cm). Weight 5 lb (2.26 kg) Maximum Power Consumption 70 Watts with PoE Environmental Tests Ingress Protection Rating IP 40 per IEC 60529 for Vertical Falling Water, Pollution Degree 3 Humidity Non-condensing Relative Humidity: 5% to 95% Military Standard MIL-STD-810G Method 514.6: Procedure 1 Category 4, Secured Cargo - Common MIL-STD-810G Method 514.6: Procedure 1 Category 20, Ground Vehicles MIL-STD-810G Method 516.6. Procedure 1, Functional Shock MIL-STD-810G Method 516.6. Procedure 5, Crash Hazard MIL-STD-810G Method 516.6. Procedure 6, Bench Handling Vibration and Shock (Railway Vehicles) EN61373 Functional Random Vibe - Category 1, Class B EN61373 Simulated Non-op Long-life Vibe - Category 1, Class B EN61373 Non-op Shock, Class B Heavy-Duty Vehicle Applications SAE J1455 Operating Random Vibe, Cab Mounted Truck SAE J1455 Operating Sinusoidal Vibe, Category 3 SAE J1455 Non-operating Sinusoidal Vibe, Category 3 SAE J1455 Handling Drop Test

UL 60950-1, 2nd edition; CAN/CSA C22.2 No. 60950-1, 2nd edition, EN 60950-1, 2nd edition; CB to IEC 60950-1, 2nd edition with all group differences and national deviations Environmental Operating Ranges Operating Temperature and Altitude -40° to 140°F (-40° to 60°C) in a sealed NEMA cabinet with no airflow -40° to 158°F (-40° to 70°C) in a vented cabinet with 40 lfm of air -29° to 167°F (-34° to 75°C) in a forced air enclosure with 200 lfm of air (type tested at +85C for 16 hours) -500 to 5,000 feet. Derate max operating temperature 1.5°C per 1000 feet. 10,000 ft maximum Humidity 10% — 95% non-condensing Table 1 Cisco IR829 Specifications (continued) Description Design Specification