Cisco 2800 Series Manual 

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Preface This preface describes the objectives, audience, organization, and conventions of the software configuration documentation for your router. It contains the following sections: • Objectives, page 1 • Audience, page 1 • Conventions, page 1 • Obtaining Documentation, page 2 • Document ...

manual. Timesaver Means the described action saves time. You can save time by performing the action described in the paragraph. Tip Means the following information will help you solve a problem. The tips information might not be troubleshooting or even an action, but could be useful information, similar to ...

http://www.cisco.com You can access international Cisco websites at this URL: http://www.cisco.com/public/countries_languages.shtml Ordering Documentation For information on obtaining documentationsee the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/ ...

Cisco Technical Support Website The Cisco Technical Support Website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day, 365 days a year, at this URL: http://www.cisco.com/techsupport Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password. If you ha ...

Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your business operation are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation. Severity 3 (S3)—Operational performance of your network is impaired, but most business operati ...

Copyright © 2004 Cisco Systems, Inc. All rights reserved. CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, ...

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Overview Cisco 2800 series integrated service routers provide a range of models in which you can install a variety of modules. The number and type of modules vary by platform. Examples of these modules include WAN interface cards (WICs), voice interface cards (VICs), voice/WAN interface cards (VWICs), ...

Cisco 2800 Series Software Configuration Documentation Unlike traditional documentation, wherein all of the information appears within one printed book, the Cisco 2800 series routers software configuration documentation takes advantage of the capabilities inherent in web-based presentation. This includes extensive hyperlinking to other information, tools, and many other resource ...

Performing Initial Configuration You can configure your router by using one of the following methods: • Initial Configuration Using the Cisco Router and Security Device Manager, page 3 • Initial Configuration Using the Setup Command Facility, page 4 • Initial Configuration Using the Command-Line Interface, page 7 Initial Configuration Using the Cisco Router and Security Device Manager Note W ...

You should consult the SDM release notes to determine if SDM is supported for the router on which you want to install it. If the following messages appear at the end of the startup sequence, Cisco Router and Security Device Manager (SDM) is installed on your router: yourname con0 is now available Press RETURN to get started. Tip If these messages do not appear, SDM was not shipped with your router. I ...

Step 2 When the following messages appear, enter yes to enter basic management setup: At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system ...

Step 8 Select one of the available interfaces for connecting the router to the management network: Enter interface name used to connect to the management network from the above interface summary: fastethernet0/0 Step 9 Respond to the following prompts as appropriate for your network: Configuring interface FastEthernet0/0: Use the 100 Base-TX (RJ-45) connector? [yes]: yes Operate in full-duplex mode? ...

Initial Configuration Using the Command-Line Interface This section describes briefly how to display a command-line interface (CLI) prompt for configuration using the CLI. You can use the CLI if the following messages appear at the end of the startup sequence: --- System Configuration Dialog --- At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any p ...

Verifying the Initial Configuration To verify that the new interfaces are operating correctly, perform the following tests: • To verify that the interfaces are operating correctly and that the interfaces and line protocol are in the correct state—up or down—enter the show interfaces command. • To display a summary status of the interfaces configured for IP, enter the show ip interface b ...

Step 4 At the prompt, enter the enable command. The default configuration file does not configure an enable password: yourname> enable yourname# Step 5 Enter the erase startup-config command: yourname# erase startup-config Step 6 Confirm the command by pressing Enter. Step 7 Enter the reload command: yourname# reload Step 8 Confirm the command by pressing Enter. The router begins executing the st ...

Step 4 (Optional) Enable local logging to support the log monitoring function: Router(config)#logging buffered 51200 warning To use SDM on a router that has received a manual configuration, see the “Starting SDM on a Manually Configured Router” section on page 10. Starting SDM on a Manually Configured Router Note By default, the DHCP server is turned off on the Cisco 28xx series routers. SDM ...

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Basic Software Configuration Using the Setup Command Facility You can configure your router by using the Cisco Router and Security Device Manager (SDM), the Cisco IOS setup command facility, or the Cisco IOS command-line interface (CLI). Note Wherever possible, we recommend that you use SDM to configure ...

OL-5992-01 Information About the Setup Command Facility Information About the Setup Command Facility The setup command facility prompts you to enter the information that is needed to configure a router quickly. The facility steps you through a basic configuration, including LAN and WAN interfaces. For more general information about the setup command facility, see the following document: Cisc ...

OL-5992-01 Using the Setup Command Facility to Perform Basic Configuration Step 3 When the following messages appear, enter yes to enter basic management setup: At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Basic management setup configures only enough connectivity for management ...

OL-5992-01 Using the Setup Command Facility to Perform Basic Configuration Step 9 Select one of the available interfaces for connecting the router to the management network: Enter interface name used to connect to the management network from the above interface summary: fastethernet0/0 Step 10 Respond to the following prompts as appropriate for your network: Configuring interface FastEtherne ...