ESP EZ-PROX Operation & User’s Manual

Text of ESP EZ-PROX Operation & User’s Manual

Equipment required for controlling one door:

12 volt DC power supply 2 amp minimum (EV-BPS) Lock - Magnetic (EVML-250)/Yale type keep 12 volt lock (enter D) Push to exit button (EVEXIT) Green break glass emergency release (EVEBG)* *Note:- for use with Magnetic lock only Functions of the EZ-PROX The EZ-PROX can control one door by use of tags. Programmable door open time 00 to 99 seconds. 1000 Tags can be programmed. Door closed function (contact r

Sighting Of The EZ-PROX

The EZ-PROX must not be located within 2 meters of any reader/keypad type devices. The EZ-PROX must not be sited back to back with reader/keypad type devices. Site the EZ-PROX within easy access to the door/doors to be controlled Fitting Using the template mark and drill the fixing and cable entry holes.

+12V - +24V

AC input ~ 12V - 24V Red-power DC input +12V - +24V Black-power AC input ~ 12V - 24V Brown-door status detecting reed switch Orange-push to exit button Yellow-DATA 1 Green-GND Blue-Door bell Purple-Door bell Gray-DATA 0 White-NO 1 Pink-COM 1 Aqua-NC 1 Shielded ground DATA 1 NO 1 COM 1 NC 1 DATA 0 Shielded ground Red Black Brown Orange Yellow Green Blue Purple Gray White Pink Aqua Wiring Diagram

Wiring Diagram for Maglock

Wiring Diagram for Yale Release

How to enter programing mode

Factory default programming code is 1234. Input the programming code twice (1234 and1234), the yellow LED will be on. To exit programming mode press # button. Programming a fob or card Note:- Do not have Tags in your hand or close by when pressing keys. EZ-PROX has 1000 locations available from 000 to 999. 1. Enter programming mode the blue LED will turn yellow. 2. Enter the location you want to programme the Tag to in a 3 digi

Programing a group of fobs or cards

Enter programing mode. 1. All tags to be programed as a group must have consecutive numbers. 2. Press the * key then the 9 key the yellow light will flash 3. Press the 0 key then the 1 key the unit will bleep once. 4. Enter the number of the first available location in the range of 000 to 999. 5. Now enter in a 3 digit format how many tags you want to programme (xxx) into the system, present the lowest number tag to the

Changing the Programming code

1. Enter programming mode. A Long bleep will be heard and the blue power LED will turn yellow. 2. Press * key followed by the 3 key the orange LED will start to flash. 3. Enter the new programming pin twice. A conformation bleep will be heard. 4. Press * 3 (yellow light blinks). Then input new administrator code twice (The length of the new admin code must be the same as the old one). Bleep - sound means it modifies successful

Delete all user fobs and cards and restore to

factory default Enter programming mode. 1. A Long bleep will be heard and the blue power LED will turn yellow. 2. Press * key followed by the 8 key theyellow LED will start to flash. 3. Press the 8 key twice. 7 conformation bleeps will sound. Set the (digit) length of password 1. Enter programming mode by entering the 4 digit pin number twice (default pin 1234). A Long bleep will be heard and the blue power LED

-10 ~ +55ºC

Voltage DC: 12V-24V AC: 12V~24V Working current <120mA Standby current <90mA Card mode ID / IC card Effective distance <5CM Capacity 1000 Cards or Fobs Elite Security Products Tel: 01527 515150 Fax: 01527 515143 email: [email protected]

ESP Intercom System Owners Instructions: