Daewoo 902D Manual
Text of Daewoo 902D Manual
NOTE : This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cuase harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a partic
Bitte lesen Sie alle diese Informationen, bevor Sie das Gerät in
Betrieb nehmen! Lesen Sie sich außerdem die
Bedienungsanleitung komplett und sorgfältig durch, da nur in
diesem Fall eine problemlose Inbetriebnahme erwartet werden
kann.
• Achten Sie darauf, daß das Gerät nur in eine 230V Schuko-
Steckdose eingesteckt wird.
• Die Steckdose sollte jederzeit frei zugänglich sein um bei
einem evtl. auftretenden Notfall das Gerät schnell vom Netz
zu
Emission Characteristics Tested by SEMKO
A sample of this type has been tested and has shown
compliance with theguidelines in the swedish document
TCO’ 95.
This product is also designed for IT power system with phase
to phase voltage of 230V.
The power cord is used as a main disconnect device.
Disconnect the power cord before servicing. The outlet must
be installed near the monitor and must be easily accessible.
As an ENERGY STAR Partner, Daewoo Elec
Introduction ............................................................ 1
Product Features ................................................ 2
Setup ........................................................................ 3
Connecting the Signal Cable and Power Cord ... 3
Connecting to the Macintosh Computer ............ 4
Power Management System ............................... 5
DDC for Plug & Play ......................................... 5
Operation &
CONNECTING THE SIGNAL CABLE AND
POWER CORD
1. Turn off the computer and monitor.
2. Connect the 15 pin D-sub connector to the output port of
the video card in your computer.
3. Tighten the screws of connector.
4. Plug the power cord into the AC receptacle located at
the back of the monitor.
5. Plug the other end of the power cord into the AC outlet.
Signal Cable
Power Cord
PRODUCT FEATURES
• The convenient and user-friendly on-screen display
allows for
POWER MANAGEMENT SYSTEM
If you use the monitor with a computer which complies
with the power saving program, you can set the monitor
to go blank when the system has remained unused for a
period of time. To specify the period or to disable this
feature, set the system timeout field of the computer’s
system setup program or use special software for power
saving. See the computer user’s manual for the details of
using the system setup. While the mo
OPERATION & ADJUSTMENT
Move cursor to the right window from the MENU
window.
Increase the value of any selected FUNCTION.
Move cursor to the left window from the MENU
window.
Decrease the value of any selected FUNCTION.
Launch OSD(On-Screen Display) MENU window.
Move cursor to the high window from the MENU
window.
Move cursor to the low window from the MENU
window.
Control Panel
MENU
Select language for OSD (5 languages).
LANGUAGE
Center Menu Functions
Language Menu Function
Adjust the position of the display
horizontally(left or right) and vertically
(up or down).
H. CENTER &
V. CENTER
Color Menu Functions
Choose different preset color
temperatures or set your own customized
color parameters.
Adjust the red gain.
Adjust the green gain.
Adjust the blue gain.
COLOR TEMP
RED GAIN
GREEN GAIN
BLUE GAIN
Adjust the red bias.
Adjust the gr
Geometry Menu Functions
Adjust the left and right margins for more
convex or more concave margins.
• Image turns to by .
• Image turns to by .
Adjust the trapezoid of the screen by
moving the lines inward or outward.
• Image turns to by .
• Image turns to by .
Adjust the side balance when the sides of
the screen are bowed towards left or right.
• Image turns