Argos 656/0159 Assembly Instructions Manual
Text of Argos 656/0159 Assembly Instructions Manual
Assembly Instructions – Please keep for future reference
Important – Please read these instructions fully before starting assembly
Dimensions
Length - 200cm
Width - 97.5cm
Height - 185cm
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 26/06/13
Metal High Sleeper
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
1
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Place the product on flat and
steady surface duri
Please check you have all the parts listed below
Components - Parts
2
1 Corner post x 2 (Ø4.5 x 184.7cm)
11 Ladder (151 x 35.7cm)
3 End panel x 2 (97 x 39.8cm)
7 Front guard (191 x 42cm)
Rear guard (191 x 42cm)
9 Slats x 2 (□2 x 1 x 95cm)
5
8 Support x 2 (Ø1.3 x 90cm)
Lower stretcher (long) (190.4 x 3cm)
6
4 Lower stretcher (short) x 2 (Ø1.9 x 88.5cm)
10 Slats x 22 ((□2 x 1 x 95cm)
2 Corner post x 2 (Ø4.5 x 184.7cm)
Smaller diameter
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
3
A
B
C
D
E
F
G
H
J
K
L
M
N
P
M6 x 15mm Allen screw x 8
M6 x 65mm Allen screw x 9
Curved washer(small) x 19
M6 x 45mm Screw x 4
M8 x 65mm Allen screw x 4
M6 x 35
Lay front corner post
,rear corner post , end
panel and lower
stretcher flat on the
floor as shown.
Note: The holes in end
panel must be at the
top.
Note: The bottom of rear
corner post is smaller
diameter.
Insert end panel into
the large holes in posts
.
Secure using fixings
and .
Note: Do not fully
tighten screws .
Assemble short lower
stretcher
Assembling rear guard
5
H
E
B
C
J
E
B
C
B
C
J
E
H
E
G
F
F
2
5
2
2
5
F
G
6
Assembly Instructions
8
6
L
8
8
L
L
Two people are needed
here.
With help, stand both
side frames upright.
Assemble rear guard
in between the side
frames as shown.
Note: Do not fully tighten
any screws during the
assembly.
Secure at the top using
fixings and as
shown.
Secure at the bottom
using fixings
and as shown.
Note: Plastic washers
are located in between
Assembling front guard
At this stage, choose if
you want the ladder on
the right hand side or left
hand side.
According to which side
you want the ladder,
assemble front guard
in between the side
frames as shown.
Secure at the top using
fixings and .
Secure at the bottom
using fixings
and .
6
7
E
E
H
E
J
C
B
G
F
F
G
H
7
C
B
E
J
E
H
F
G
7
1
Assembly Instructions
Alternative
assembly
F
F
J
B
C
Assemble ladder to
front guard using
fixings and .
Note: fixings are
located inside the frame
as shown.
Attaching ladder
11
J
C
K
J
C K
J
K
C
11
11
7
7
7
J