Arcom RC210 Assembly Manual

Aurora, Oregon 97002 (503) 678-6182 [email protected] http://www.arcomcontrollers.com/ RC210 Repeater Controller Assembly Manual Hardware Version 3.3 Reproduction or translation of any part of this manual beyond that permitted by sections 107 or 108 of the 1976 United States Copyright Act (or its legal successor) without the express written permission of Arcom Communications is unlawful as noted below. Requests for permission to copy or for further information should be addressed to Arcom Communications. Except as noted above, permission is hereby granted for any non-profit group or individual to reproduce any ...

blank RC210 Repeater Controller Assembly Manual Hardware Version 3.3 ...

and verify against this list. Resistors, 1/4 watt ( ) 12 10k ohm (brown-black-orange-gold) ( ) 3 22k ohm (red-red-orange-gold) ( ) 4 47k ohm (yellow-violet-orange-gold) ( ) 10 100k ohm (brown-black-yellow-gold) ( ) 3 470k ohm (yellow-violet-yellow-gold) ( ) 3 110k ohm (brown-brown-yellow-gold) ( ) 3 33k ohm (orange-orange-orange-gold) ( ) 23 470 ohm (yellow-violet-brown-gold) ( ) 2 47ohm (yellow-violet-black-gold) Resistor Networks ( ) 1 470 ohm network (471 or 470) ( ) 1 10K ohm network (103G) Potentiometers ( ) 6 10k ohm (C103) ( ) 3 500k ohm (C504) Capacitor ...

temperature controlled, fine-tipped soldering iron and good quality 60/40 rosin-core solder for construction. Follow standard construction practices when building the unit. You will also need small flush or semi-flush cutting pliers and small-tipped needle nosed pliers. A magnifying glass may prove useful for identifying the values of small parts. Keep the tip of the soldering iron bright and clean, wiping it frequently on a wet sponge or rag. Make solder joints carefully, but swiftly. Prolonged heat on a PC board pad can be disastrous and ruining this PC board can be expensive! ...

the leads face the back of the trim pot body. Then insert the leads through the holes in the PC board, with the body closest to the edge of the board, it is flush against the board. Then solder the connections. (note: the pots should lay down against the board, with the adjustment slot facing up) 10K ohm (C103) ( ) Port1 Disc, Port2 Disc, Port3 Disc ( ) Record, Play, Tone 500K ohm (C504) ( ) P1 Tx, P2 Tx, P3 Tx Capacitors The following capacitors are .1uf (104) and should be mounted as close to the board as possible without stressing the leads. ( ) C2, C3, C5, C6, ...

board marked "Power". It should be installed so it fits inside the outline marked on the PC board. ( ) Power 4 pin (green) Voltage Regulators IC1 is installed laying down on the PC board with the heatsink between it and the PC board . Carefully bend IC1’s leads 90 degrees and insert into the appropriate holes in the board. Slide the heatsink in place and use the supplied 4/40 screw and nut to secure the assembly through the hole in the board. ( ) IC1 78M05 (LM340T5) IC7 looks like a transistor. It should be installed just like the transistors. ( ) IC7 78L033 (CZ-3.3) Inductor L1 l ...

Double check your work. ( ) All solder connections are bright and shiny. ( ) No solder bridges between IC socket pins. ( ) All components are installed in their correct positions. ( ) Diodes, transistors, voltage regulators and electrolytic capacitors are installed with their proper polarity. ( ) The pc board modifications are done correctly. Congratulations! At this point your RC210 is completely assembled except for the integrated circuits. These will be installed after you run some voltage checks. Checking Voltages For these tests, you will need to connect power to the RC210. It is suggested that you use a power supply with cu ...

We offer several ways you can obtain assistance with your RC210: Our email list (it's a good idea for all RC210 owners): Send an email to: mailto:[email protected] Or you may contact us directly at: Arcom Communications 24035 NE Butteville Rd. Aurora, Oregon 97002 (503) 678-6182 email: [email protected] RC210 Repeater Controller Assembly Manual Hardware Version 3.3 ...