Antari Z-380 Operation & User’s Manual

machines in the DMX chain. The machine uses an 3 or 5 pin XLR connector for DMX connection, the connector is located on the rear of the machine. DMX Channel Function Channel Mode Channel Value Function 2 1 0-5 Faze off 2 6-255 Faze 1-100% 1 1 0-5 Faze off Fan 100% 6-255 Faze 1-100% Fan 100% Sync 1 0-5 Faze Off Fan 20% 6-255 Faze 1-100% Fan 21-100% Fluid Only use Antari FLG water-based liquid for the Z-380 Fazer. The machine is tested and 10 ...

The machine can be operated with onboard digital control interface or two rotary knobs located on the rear. Rotary Knob Function SMOKE Turn haze on/off, adjust output volume from 0~100% FAN Adjust fan speed from 20%~100% Button Function [MENU] Scroll through setting menu ▲ [UP]/[TIMER] Up/Activate Timer function ▼ [DOWN]/[VOLUME] Down/Activate Volume function [STOP] Deactivate Timer/Volume function Control Menu Set interval from 1 to 180 seconds Set duration from 1 to 120 seconds Set timer output from 1 to 100% Interval Set 180s Duration Set 120s Timer Out ...

＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿� ...

other type of liquid is used, improper use of liquid may lead to machine failure and malfunction. Service and Maintenance ․ Do not allow the machine to become contaminated. ․ Remove dust from air vents with air compressor, vacuum or a soft brush. ․ Only use a damp cloth to clean the casing. ․ Before storing run distilled water through the system to help avoid condensing the pump or heater. ․ It is recommended to run the machine on a monthly basis in order to achieve best performance and outpu ...

＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿ ＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿� ...

transmitters. Follow below steps to pair or delete transmitter from receiver. Step 1: Power off Z-380 Fazer Step 2: Press and hold [DOWN] button Step 3: Turn power on and hold [DOWN] button until below menu shows on display Step 4A: Press [UP] to pair a new transmitter; press any button on the W-2 remote to finish pairing. Step 4B: Press [DOWN] button to delete existing transmitter. Transmitter battery replacement If effective distance seems to be decreased, it is possible the battery ...

Wireless remote control system W-2 consists of a transmitter equipped with four buttons to turn faze output on or off, and adjust output volume; with an onboard receiver attach to the rear panel of Z-380. W-2 Wireless Transmitter Wireless Receiver Wireless remote control function: [A] button – Turn on faze output [B] button – Turn off faze output [C] button – Increase output volume [D] button – decrease output volume In a free open space the effective distance is 50 meters, actual usage depending on obstacle level the effective distance is 10-25 meters. 8 ...

Set fan output from 20 to 100% Set DMX address from 1 to 511 Set DMX mode Sync, 1Ch or 2Ch Turn On or Off wireless control Turn On or Off run last setting function Remote Control Operation (Optional) To operate the machine by remote control, connect the remote to the microphone jack located on the rear of machine. Use the switch to turn haze on/off, and use the rotary knob to adjust the output volume from 0~100%. Volume Out 100% Fan Out 100% DMX512 Add. 511 DMX Mode 1Ch Wireless OFF Quick StartOFF 7 ...