Netkrom AIR-PT900L Quick Installation Manual

AIRNET 54 Mb CPE Bridge Point to Point Kit Series Package Contents: • 2 Netkrom CPE units • Two Mounting bracket include: 2 stainless steel U-Bolt, 2 mounting brackets, 2 pipe Brackets and 4 screw nuts • Two PoE Injectors • Two Power Cables • Two RJ45 Waterproof Connector System • CD-ROM • Two 75’ Outdoor Rated Cat5e shielded cables ...

• NETKROM shall not be liable for incidental or consequential damages resulting from the furnishing, performance, or use of this manual. • Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When instal ...

Take a moment to ensure you have all of the following parts in your Outdoor Waterproof Unit installation kit before you begin installing the product. If any parts are missing, please contact your local vendor or contact us, please see the contact information in Section 6. ...

following is available: • CAT5/5e or FTP Outdoor Ethernet cable (from the CPE to PoE Injector) • At least one computer is installed with a Web browser and a wired or wireless network interface adapter • TCP/IP protocol is installed and IP address parameters are properly configured on all your network’s nodes Important! • Configure and verify the CPE operations first before you mount the u ...

Outdoor cat.5 Ethernet cable with waterproof connector to the RJ-45 connector located in the CPE. Then connect the other end of the cable to the PoE injector. For the Netkrom PoE, the recommended length of the Category 5 cable is up to 260 feet or 80 meters. 1.- Remove the thin enclosure nut from the feedthru assembly. This can be discarded. Loosen the compression nut completely 2.- Insert ...

the RJ45-ECS housing which is already mounted in the CPE. There should be a rubber gasket between the two assemblies. Tighten the feedthru assembly to create a seal. 5.- The final step is to tighten the compression nut until the gaskets are tight around the Cat5 cable. Always push the cable toward the connector while tightening to ensure good strain relief of cable to connector. Step 2 From the PoE injector conne ...

CPE in a Pole or Tower Netkrom CPE device can be mounted on the pole or tower as shown in following: 1.-Attach the mounting bracket to the back of the CPE using the three hex screws provided. (Do not over tighten the screws.) Note: The bracket in the illustration side shows the normal orientation which allows the CPE to be pointed up towards the base station antenna. However, if you live somewhere that would require you pointing the CP ...

uConfig is a feature that provides the ability to directly access the CPE without the need to know absolutely its IP address. It may be run directly from the product CD or installed on the user’s PC for later access. Using uConfig When you execute the uConfig file you should see a window as it is shown on the right side. Click yes to continue The screen is divided into three sections. The top section shows the Ethernet ...

The default browser will be loaded using the correct IP address of the CPE (regardless of how the computer’s TCP/IP properties are set), Default Password: password Click on LLO OG GIINN!!, and start configuring the . Click the O radio. ...

If you don’t use the uConfig Utility you need to establish Ethernet connection between your PC and the CPE, by default the CPE has the IP address 192.168.168.1. Therefore, your PC must be in the same network segment as the CPE is to get Ethernet connectivity. tep 1 o to Start button, then go to My Network laces and finally click on Network onnections. ight-Click over your network adapter and elect Properties. Propert ...

manual. Getting Started Address bar, enter You can start configuring your CPE using either your Web Browser or the uConfig utility. At the http://192.168.168.1 and press Enter on your LOGIN! en reach the home page of your keyboard. At the login page, click on the button to enter the configuration page. D ...

Setup The CPE Bridge Point to Point Kit is commonly used in Point-to-Point Applications. ou ca Y c n implement a Point-to-Point onnection by simply setting one access point RootAP in Access Point mode and setting parent Client as the other access point in Trans mode or in Client Mode. NOTE • Client Mode does not provide transparent bridging. • Transparent Client Mode does provide transparent bridging. Follow these steps to setu ...

Client/s. elect the Remote AP MAC checkbox. Step 2 Select the Remote AP MAC checkbox. Enter the Remote AP MAC. Check the MAC address of your Remote AP under About system >> Wireless MAC Note: When using Remote AP MAC, the ESSID name must also match the AP’s ESSID name, especially when Closed System is enabled on the AP. Repeat the Transparent Client steps to add more Clients to the Point-to-MultiPoint Step 1 S Ente ...

Conversion ( AIR-PTP900L ) have to 900 In order to use your 900 MHz CPE, you select in Wireless Profile any of the following options: 802.11b only 802.11g only 802.11b/g mixed (recommended) Channel conversion from 2.4 GHz to MHz: Channel 10 or 11 must be used in an Operational Mode when using a 900 MHz CPE. y 802.11 b/g 900 MHz Channel 10 (2457) 913 MHz Channel 11 (2462) 918 MHz ...

1. - Advanced Routing Configuration: Please go to page 85 of User Manual. 2 th Control: Please go to page 95 of User Manual. 3. – Remote Management: Please go to page 99 of User Manual. 4. – Advanced Wireless Configuration: Please go to page 114 of User Manual. 5. – Wireless Security Setup: Please go to page 135 of User Manual. 6. – Security Configuration: Please go to page 143 of Us 7 go to page . ...

the capabilities and advanced configuration of our product please see the user manual. Contact Information Miami FL 33178 Phones: Fax: (+1) 305-418-9266 Sales and ordering: American Customers: [email protected] Address: 5930 NW 99th Avenue Unit 14, El Doral, (+1) 305-418-2232 Worldwide Customers: [email protected] ...