Vive TP-S-855C Installation Manual

Description Gas or Oil Heat Electric Furnace Heat Pump (No Aux. or Emergency Heat) Heat Pump (With Aux. or Emergency Heat) Multi-Stage Systems Heat Only Systems Cool Only Systems Millivolt Yes Yes Yes Yes Yes Yes Power Type Battery Power Hardwire (Common Wire) Hardwire (Common Wire) with Battery Backup Table of Contents Installation Tips Thermostat Quick Reference Private Label Badge Wiring Wiring Diagrams Technician Setup Menu Programming Features Specifications Page A trained, experienced technician must install this product. Carefully read these instructions. You could damage this product or cause a hazardous condition if you fail to follow these instructions. Una version en español de este manual se puede descargar en la pagina web de la compañia. Rev. 1821 U.S. Registered Trademark. Patents pending Copyright 2018 All Rights Reserved. 5-7 8 13-19 2-4 Yes Yes 20-27 Mount Thermostat Align the 4 tabs on the subbase with corresponding slots on the back of the thermostat, then push gently until the thermostat snaps in place. Installation Tips Note: To ensure a solid fit between the thermostat and the subbase: 1. Mount subbase to a flat wall 2. Use screws provided 3. Drywall anchors should be flush with the wall 4. Wires should be pushed into the wall Installation Tips The thermostat should be installed approximately 4 to 5 feet above the floor. Select an area with average temperature and good air circulation. • Close to hot or cold air ducts • That are in direct sunlight • With an outside wall behind the thermostat • In areas that do not require conditioning • Where there are dead spots or drafts (in corners or behind doors) • Where there might be concealed chimneys or pipes Wall Locations Pick an installation location that is easy for the user to access. The temperature of the location should be representative of the building. Installation Tip Do not install thermostat in these locations: Installation Tips 28-29 30 Vertical Mount Horizontal Mount For horizontal mount put one screw on the left and one screw on the right. All of our products are mercury free. However, if the product you are replacing contains mercury, dispose of it properly. Your local waste management authority can give you instructions on recycling and proper disposal. Mercury Notice Failure to disconnect the power before beginning to install this product can cause electrical shock or equipment damage. Installation Tip: Electrical Hazard For vertical mount put one screw on the top and one screw on the bottom. Subbase Installation 11-12 9-10 Vive Comfort Toll Free : 888-776-1427 Web: www.vivecomfort.com Hours of Operation: M-F 9AM - 6PM Eastern TP-S-855C P.O. Box 3377 Springfield, MO 65804

and cooling system. This thermostat may also be configured for a heat pump system. See the “heat pump” configuration step on page 17 of this manual to configure the thermostat for heat pump applications. Wiring Terminal 2 Heat 2 Cool Conventional System 2 Heat 2 Cool Heat Pump System 3 Heat 2 Cool Heat Pump System RC RH C B O G W/E Y Y2 W2 Transformer power (cooling) Transformer power (heating) Transformer common Energized in heating Energized in cooling Fan relay First stage of heat First stage of cool Second stage of cool Second stage of heat Transformer power (cooling) Transformer power (heating) Transformer common Heat pump changeover valve energized in heating Fan relay First stage of emergency heat First stage of heat & cool Second stage of cool Auxiliary heat relay, second stage of heat Heat pump changeover valve energized in cooling Transformer power (cooling) Transformer power (heating) Transformer common Heat pump changeover valve energized in heating Fan relay First stage of emergency heat First stage of heat & cool Second stage of cool & second stage of heat Auxiliary heat relay, third stage of heat Heat pump changeover valve energized in cooling Wiring Caution: Electrical Hazard All components of the control system and the thermostat installation must conform to Class II circuits per the NEC Code. Warning: Do not overtighten terminal block screws, as this can damage the terminal block. A damaged terminal block can keep the thermostat from fitting on the subbase correctly or cause system operation issues. Installation Tip Max Torque = 6in-lbs. Wiring If you are replacing a thermostat, make note of the terminal connections on the thermostat that is being replaced. In some cases the wiring connections will not be color coded. For example, the green wire may not be connected to the G terminal. Loosen the terminal block screws. Insert wires then retighten the terminal block screws. Place nonflammable insulation into the wall opening to prevent drafts. 1. 2. 3. Wiring Tips C Terminal The C (common wire) terminal does not have to be connected when the thermostat is powered by batteries. Wire Specifications Use shielded or non-shielded 18-22 gauge thermostat wire. Failure to disconnect the power before beginning to install this product can cause electrical shock or equipment damage. Note: In many heat pump systems with no emergency heat relay, a jumper can be installed between E and W2 to turn thermostat into a single stage control for Emergency Heat Operation. Thermostat Quick Reference The low battery indicator is displayed when the AA battery power is low. If the user fails to replace the battery within 21 days, the screen will only show the low battery indicator but maintain all functionality. If the user fails to replace the batteries after an additional 21 days (days 22-42 since first “low battery” display) the setpoints will change to 55˚F (Heating) and 85˚F (Cooling). If the user adjusts the setpoint away from either of these, it will hold for 4 hours then return to either 55˚F or 85˚F. After day 63 the batteries must be replaced immediately to avoid freezing or overheating because the thermostat will shut the unit off until the batteries are changed. Important Indicates the current room temperature Time and day of the week Staging Indicators: +1 will appear in the display when second stage of heat or cool is on. +2 will appear for the third stage of heat. Setpoint: Displays the user selectable setpoint temperature. Hold: is displayed when the thermostat program is permanently overridden. System Operation Indicators: If these or the Fan indicator are flashing, it means that the system is in a delay of some type (compressor delay, cooling fan delay, staging delay). 1 2 3 7 8 9 Low Battery Indicator: Replace batteries when this indicator is shown. Program Menu Options: Show different options during programming. Program Time Periods - Residential: Uses 4 time periods - WAKE, RETURN, LEAVE & SLEEP. Commercial: Uses 2 or 4 time periods that appear in the text field - Occupied & Unoccupied. 7 3 2 2 1 8 9 Getting to know your thermostat Thermostat Quick Reference Battery Installation Battery installation is recommended even if the thermostat is hardwired (C terminal connected). When the thermostat is hardwired and batteries are installed, the thermostat will activate a compressor delay of 5 minutes when it detects a power outage from the hardwired power supply. Important: High quality alkaline batteries are recommended. Rechargeable batteries or low quality batteries do not guarantee a 1-year life span. Insert 2 AA Alkaline batteries (included). High quality alkaline batteries are recommended. Simple operating instructions are found on the back of the battery door. To release battery cover press finger bevel on the left side and lift the cover to access batteries.

Glow in the dark light button Setpoint buttons Program buttons Menu button Fan button 1 LCD Display 2 3 4-6 7 8 9 System button 10 11 Button/battery access door Battery cover Gently slide a screwdriver into the bottom edge of the badge. Gently turn the screwdriver counter clockwise. The badge is held on by a magnet in the well of the battery door. The badge should pry off easily. DO NOT USE FORCE. About The Badge All of our thermostats use the same universal magnetic badge. Visit the company website to learn more about our free private label program. Private Label Badge Magnet in door Use the bevel on lower ridge Thermostat Quick Reference Wiring Diagrams Wiring Diagrams Typical 2H/2C System: 1 Transformer Typical 2H/2C System: 2 Transformer Typical 3H/2C or 2H/1C Heat Pump System Typical Heat-Only System Typical Heat Only System With Fan Typical Cool-Only System HEAT RELAY RC RH Y C W/E G C R L2 L1(HOT) FAN RELAY HEAT RELAY RC RH Y C W/E G C R L2 L1(HOT) FAN RELAY COMPRESSOR RELAY C R L2 L1(HOT) RC RH Y C G Power supply Factory-installed jumper. Remove only when installing on 2-transformer systems Use either O or B terminals for changeover valve Optional 24 VAC common connection when thermostat is used in battery power mode W/E RC RH Y C W/E G W2 Y2 COMPRESSOR RELAY FAN RELAY AUXILIARY HEAT RELAY COMPRESSOR RELAY 2 EMERGENCY HEAT RELAY COOL CHANGE OVER VALVE HEAT CHANGE OVER VALVE C R L2 L1(HOT) REMOVE JUMPER RC RH Y C W/E G W2 Y2 C R L2 L1(HOT) C R L2 L1(HOT) COMPRESSOR RELAY HEAT RELAY FAN RELAY HEAT RELAY 2 COMPRESSOR RELAY 2 RC RH Y C W/E G W2 Y2 COMPRESSOR RELAY FAN RELAY HEAT RELAY 2 COMPRESSOR RELAY 2 HEAT RELAY C R L2 L1(HOT) O B 2 3 7 8 9 11 10 1

minimum number of minutes that the fan will run per IAQ mode cycle. The thermostat will keep track of fan runtime from normal heat and cool operation. If addi- tional fan runtime is needed, the thermostat will run the fan to satisfy the IAQ mode minutes. IAQ Mode Minutes Select 1, 5, 10, 15, 20, 30 or 45 minutes. When IAQ fan mode is enabled, it will ensure the fan runs at least the selected number of minutes per IAQ Mode Cycle. This step will not appear if previous step is set to “OFF”. This feature allows a delay to occur if an additional stage is needed. This allows the previous stage extra time to satisfy the setpoint. Staging Delay Use the or key to turn on or off. OFF 1 IAQ MODE MINUT Satisfy Setpoint This feature allows the thermostat to keep multiple stages of heat or cool energized until the setpoint is satisfied. SS STAGING Use the or key to select OFF, 5, 10, 15, 30, 45, 60, or 90 minutes. OFF 5 STAGING dl The cooling fan delay setting will delay the fan from coming on in cool mode and keep it running after the compressor shuts off for a short time to save energy in some systems. Cooling Fan Delay OFF You can set the cooling fan delay to OFF, 15, 30, 60 or 90 seconds. If 15, 30, 60, or 90 is selected the fan will not turn on for that many seconds when there is a call for cool and will run for that many seconds after satisfying a call for cool. COOL FAN DL IAQ Mode Cycle This feature will configure the fan to run a selected number of cycles per hour. Note: This mode can be enabled or disabled at anytime during normal operation by selecting IAQ mode with the fan key. Select OFF, 1, 2, 3 or 4 with the or keys. This sets the number of cycles per hour that the IAQ fan mode will operate. OFF IAQ MODE CYCLE Tech Setup Steps Adjustment Options Default LCD Will Show Technician Setup Menu For Dual Fuel applications (Gas/ Fossil fuel Auxiliary Heat), turn this setting ON to LOCKOUT the Heat Pump (Y) when Auxiliary Heat (W2) is on. If desired - This can also be used with Electric Auxiliary. You can configure the system switch for the particular appli- cation. Heat - Off - Cool, Heat - Off, Cool - Off, Heat - Off - Cool - Auto Note: EM. Heat will show if in heat pump mode. System Set Use the or key until the desired application is flashing. AUTO = Auto changeover You can configure the thermostat to operate a 3 stage heat pump system. 2H 2C = 2 heat, 2 cool 3H 2C = 3 heat, 2 cool This feature is shown only if the HEAT PUMP technician setup step is ON. Stages of Heat Use the or key to change between 2 or 3 stages of heat. 2 heat will use Y1 as first stage and W2 as auxiliary. 3 heat will use Y1 as the first stage, Y2 as the second stage and W2 as the auxiliary. Dual Fuel Auxiliary for Heat Pump Will only appear if Heat Pump setting is turned ON OFF Will allow Y(1st stage of Heat) and W2 (Aux Heat) to run together if called for. ON Will de-energize Y termi- nal 45 seconds after a call for Auxiliary Heat (W2). Heat Pump When turned on the thermostat will operate a heat pump. 1. EM. Heat will show as an option in the system switch. 2. Y will be first stage of heat & cool, W/E will be emergency heat relay & W2 will be auxiliary heat relay. OFF configures the thermostat for non heat pump systems. ON configures the thermostat for heat pump systems. OFF HEAT OFF COOL A6 OFF OFF 2H2C 2 STAGES Tech Setup Steps Adjustment Options Default LCD Will Show Technician Setup Menu This feature allows the installer to change the calibration of the room temperature display. For example, if the thermostat reads 70˚ and you would like it to read 72˚ then select +2. OFF This feature will flash a reminder after the elapsed run time to remind the user to change the filter. A setting of “OFF” will disable this feature. Filter Change Reminder You can adjust the filter change reminder from “OFF” to 2000 hours of runtime in 50 hour increments. Tech Setup Steps Room Temperature Calibration 0˚F This feature allows the installer to select the minimum run time for the compressor. For example, a setting of 4 will force the compressor to run for at least 4 minutes every time the compressor turns on, regardless of the room temperature. You can set the minimum compressor run time to “OFF”, “3”, “4”, or “5” minutes. If 3,4 or 5 is selected, the compressor will run for at least the selected time before turning off. Minimum Compressor On Time OFF You can adjust the room temperature display to read up to 4˚above or below the factory calibrated reading. Adjustment Options Default LCD Will Show OFF SE CAL 0 O F OFF Technician Setup Menu This thermostat has a technician setup menu for easy installer configuration. To set up the thermostat for your particular application: 1. Press the MENU button. 2. Press and hold the TECH SET button for 3 seconds. This 3 second delay is designed so that homeowners do not accidentally access the installer settings. 3. Configure the installer options as desired using the table below. Use the or keys to change settings and the NEXT STEP or PREV STEP key to move from one step to another. Note: Only press the DONE key when you want to exit the Technician Setup options. 4. Press the DONE key to exit. Keypad Lockout Note: The selected keypad lockout functionality must be activated after exiting tech setup. If you do not perform this procedure, all keys will function freely. To lock the keypad hold down the and keys for 3 seconds. You will see a lock in the display. To unlock the display hold down the and keys for 3 seconds. The compressor short cycle delay protects the compressor from “short cycling”. This feature will not allow the compressor to be turned on for 5 minutes after it was last turned off. Compressor Short Cycle Delay ON Selecting “ON” will not allow the compressor to be turned on for 5 minutes after the last time the compressor was on. Select “OF” to remove this delay. CO ON OF Tech Setup Steps Adjustment Options Default LCD Will Show Keypad Lockout Keypad lockout allows you to configure the thermostat so that some or all of the keys don’t function. OF= keypad lockout has been disabled. PA= partial keypad lockout, which locks all the keys except the or keys. FU= full keypad lockout, which locks out all the keys. OF See Keypad Lockout Note PA The swing setting often called “cycle rate”, “differential” or “anticipation” is adjustable. A smaller swing setting will cause more frequent cycles and a larger swing setting will cause fewer cycles. Cooling Swing The cooling swing setting is adjustable from 0.2˚ to 2˚. For example: A swing setting of 0.5˚ will turn the cooling on at approximately 0.5˚ above the setpoint and turn the cooling off at approximately 0.5˚ below the setpoint. The swing setting often called “cycle rate”, “differential”, or “anticipation” is adjustable. A smaller swing setting will cause more frequent cycles and a larger swing setting will cause fewer cycles. Heating Swing 0.5 dFCO 0.5˚ The heating swing setting is adjustable from 0.2˚ to 2˚. For example: A swing setting of 0.5˚ will turn the heating on at approximately 0.5˚ below the setpoint and turn the heating off at 0.5˚ above the setpoint. 0.4˚ 0.4 dFHE Swing Setting Tip The second stage will turn on at 2x the swing setting. The second stage will turn off when 1x the swing is reached. For example, if the swing setting is .5 degrees for heating and the thermostat is set at 70˚F, the first stage will turn on at approximately 69.5˚F. The second stage will turn on at 69˚F. The second stage will turn off at 69.5˚F and the first will turn off at 70.5˚F. If the third stage is used, it will turn on at 68.5˚F and turn off at approximately 69˚F. Technician Setup Menu HEAT OFF COOL CALIBRATE MIN COMP HEAT PUMP SYSTEM SET COMP DELAY COOL SWING HEAT SWING KEY LOCK OFF OFF 1

checked by navigating to its tech setup step. The elapsed time will then appear in the text field. It can also be reset at that time by holding down the set time/run sched button for 3 seconds. Resetting an expired reminder can be done without entering tech setup, by holding down the set time/run sched button for 3 seconds from the home screen. A Note about IAQ Mode This programmable/selectable mode will operate the fan 1-4 cycles per hour, 1-45 minutes per cycle. Once programmed in tech setup, to enable this mode select “IAQ” with the fan key. Disable this mode by selecting “ON” or “AUTO” with the fan key. Enables a reminder for the user to change the humidity pad. Humidity Pad Reminder Enables a reminder for the user to change the UV light bulb. UV Lamp Reminder OFF Use the or key to select OFF, 600, 1000, 1500, or 2000. These represent hours of heat operation. Enables a reminder for the user to change the PHI Cell after 25,000 hrs. IAQ Cell Reminder Use the or key to select OFF, or 250 (stands for 25,000 hours). OFF HUM PAD 2000 OFF UVLAMP 00000 Use the or key to select OFF, 1YEAR, 2YEAR. OFF OFF 250 Tech Setup Steps Adjustment Options Default LCD Will Show Technician Setup Menu Programming Set Time Follow the steps below to set the day of the week and current time: 1. Press the MENU button. 2. Press SET TIME. 3. Day of the week is flashing. Use the or key to select the current day of the week. 4. Press NEXT. 5. The current hour is flashing. Use the or key to select the current hour. When using 12-hour time, make sure the correct a.m. or p.m. choice is selected. 6. Press NEXT. 7. Minutes are now flashing. Use the or key to select current minutes. 8. Press DONE when completed. (If using programming) All our programmable thermostats are shipped with an energy saving default program. You can customize this default program by following the instructions in the set program schedule section starting on page 24. Programming Your thermostat can be programmed to have each day of the week programmed uniquely (7 days), all the weekdays the same with a separate program for Saturday and a separate program for Sunday (5+1+1), or non-programmable. For the 7-day and 5+1+1 programming modes, there are three time period options. 1. “4” Residential (WAKE, LEAVE, RETURN, SLEEP) 2. “2C” Commercial (OCCUPIED, UNOCCUPIED) 3. “4C” Commercial (OCCUPIED 1, UNOCCUPIED 1, OCCUPIED 2, UNOCCUPIED 2) This thermostat has a programmable fan feature, which allows you to run the fan continually during any time period. This feature allows you to set a minimum cooling setpoint limit. The setpoint temperature cannot be lowered below this value. This feature allows you to set a maximum heating setpoint limit. The setpoint temperature cannot be raised above this value. Heating Temperature Setpoint Limit Use the or key to select the maximum heat setpoint. This feature allows you to display temperatures in either Fahrenheit or Celsius. ˚F or ˚C ˚F ˚F for Fahrenheit ˚C for Celsius You can select either a 12 or 24 hour clock setting. 12 or 24 Hour Clock Select GAS for systems that control the fan during a call for heat. Select ELEC to have the thermostat control the fan during a call for heat. Fan Operation 90 78 12H 12 HOUR CLOCK GAS ELE Cooling Temperature Setpoint Limit Use the or key to select the minimum cool setpoint. 44 44˚F 90˚F HE CO O F Use the or key to select 12 or 24 hour clock. GAS or ELEC This feature will start heating early to bring the building temperature to its programmed setpoint by the beginning of the WAKE, OCCUPIED time period. Morning Recovery ON Use the or key to turn on or off. You can configure this thermostat to have a 7 day program, a 5+1+1 program or as nonprogrammable. Program Options 5d Use the or key to select 7d for 7 day, 5d for 5+1+1, or 0d for nonprogrammable. 5d The display light can be configured to stay on all the time or come on when any key is pressed. NOTE: HARDWIRE ONLY Keeping the display light continually “ON” will greatly reduce battery life. The pre-occupancy fan settings will energize the fan before the occupied time to provide ventilation prior to scheduled occupancy. This feature only shows if the technician setup step for time periods is set to 2C or 4C. Pre-Occupancy Fan You can select the pre-occupancy fan from OFF, 1, 2, or 3 hours. If 1, 2, or 3 is selected, the fan will turn on that many hours prior to the scheduled occupied time period. Tech Setup Steps Allows you to put your phone number in the display. You can choose ON or OFF. Contractor Call Number If selected ON, you will see the input screen after pressing NEXT STEP. Use the or key to select the desired number and the FAN or SYSTEM key to move from one character to another. See note below for operation. Adjustment Options Default LCD Will Show When any key is pressed an audible beep will sound. You can choose ON or OFF. Beep PRE OCCUPY FAN Display Light Use the or key to to turn on or off. OFF configures the display light to come on when the light key or any button is pressed. ON configures the display light to stay on. Time Periods You can configure this thermostat to have 2 or 4 programmable time periods per day. 4 time periods are Wake, Leave, Return & Sleep. 2C time periods are Occupied & Unoccupied. 4C time periods are Occupied 1, Unoccupied 1, Occupied 2, & Unoccupied 2. Use the or key to select 4, 2c, or 4c time periods per day. 4 OFF OFF dL If ON is selected the beep will sound. If OFF is selected there is no sound. 4 OFF OFF ON b Tech Setup Steps Adjustment Options Default LCD Will Show Contractor Call Number Note If contractor call number is selected ON, the phone number entered will show in the display if there has been a continuous call for heating or cooling for 24 hours or if the light button is held down for 3 seconds. To remove the phone number from the display, hold the light button down for 3 seconds. Technician Setup Menu Technician Setup Menu OFF 4 MORN RECOV PROGRAM TIME PERIOD

1. Select HEAT or COOL with the SYSTEM key. Note: You have to program heat and cool each separately. 2. Press the MENU button (If menu does not appear first, press RUN SCHED). 3. Press SET SCHED. Note: Monday-Friday is displayed and the OCCUPIED text is shown. You are now programming the OCCUPIED time period for the weekday setting. 4. Time is flashing. Use the or key to make your time selection for the weekday OCCUPIED time period. Note: If you want the fan to run continuously during this time period, select ON with the FAN key. If you want to use IAQ mode during this time period, select IAQ with the fan key. 5. Press NEXT. 6. The setpoint temperature is flashing. Use the or key to make your setpoint selection for the weekday OCCUPIED period. 7. Press NEXT. 8. Repeat steps 4 through 7 for the weekday UNOCCUPIED time period. To customize your 5+1+1 Program schedule, follow these steps: Weekday: Repeat steps 4 through 7 for the Saturday OCCUPIED time period and for the Saturday UNOCCUPIED time period. Saturday: Repeat steps 4 through 7 for the Sunday OCCUPIED time period, and for the Sunday UNOCCUPIED time period. Sunday: (OCCUPIED, UNOCCUPIED) 1. Select HEAT or COOL with the SYSTEM key. Note: You have to program heat and cool each separately. 2. Press the MENU button (If menu does not appear first, press RUN SCHED). 3. Press SET SCHED. Note: Monday is displayed and the WAKE/OCC1 icon is shown. You are now programming the WAKE/OCC1 time period for that day. 4. Time is flashing. Use the or key to make your time selection for that day’s WAKE/OCC1 time period. Note: If you want the fan to run continuously during this time period, select ON with the FAN key. If you want to use IAQ mode during this time period, select IAQ with the FAN key. 5. Press NEXT. 6. The setpoint temperature is flashing. Use the or key to make your setpoint selection for that day’s WAKE/OCC1 period. 7. Press NEXT. 8. Repeat steps 4 through 7 for that day’s LEAVE/UNOCC1 time period, for that day’s RETURN/OCC2 time period, and for that day’s SLEEP/UNOCC2 time period. To customize your 7 day 4 time period Program schedule, follow these steps: Monday: Repeat steps 4 through 8 for the remaining days of the week. A Note About Auto Changeover: In Auto you have the ability to switch between Auto Heat or Auto Cool by pressing the system key. This can be done once the current mode has reached its setpoint. For example: if in Auto Heat, the heat setpoint must be satisfied before the thermostat will allow you to switch to Auto Cool. You can switch out of Auto by holding down the system key. To get back into Auto, you must toggle the system key to Auto. Default Programming Factory Default Program Day of the Week Events Time Setpoint Temperature (HEAT) Setpoint Temperature (COOL) Weekday Saturday Sunday Wake/OCC1 Leave/UNOCC1 Return/OCC2 Sleep/UNOCC2 Wake/OCC1 Leave/UNOCC1 Return/OCC2 Sleep/UNOCC2 Wake/OCC1 LeaveUNOCC1 Return/OCC2 Sleep/UNOCC2 6 AM 8 AM 6 PM 10 PM 6 AM 8 AM 6 PM 10 PM 6 AM 8 AM 6 PM 10 PM 70˚F (21˚C) 62˚F (17˚C) 70˚F (21˚C) 62˚F (17˚C) 70˚F (21˚C) 62˚F (17˚C) 70˚F (21˚C) 62˚F (17˚C) 70˚F (21˚C) 62˚F (17˚C) 70˚F (21˚C) 62˚F (17˚C) 75˚F (24˚C) 83˚F (28˚C) 75˚F (24˚C) 78˚F (26˚C) 75˚F (24˚C) 83˚F (28˚C) 75˚F (24˚C) 78˚F (26˚C) 75˚F (24˚C) 83˚F (28˚C) 75˚F (24˚C) 78˚F (26˚C) Programming Factory Default Program for 2 Time Periods Day of the Week Events Time Setpoint Temperature (HEAT) Setpoint Temperature (COOL) Weekday Saturday Sunday OCCUPIED UNOCCUPIED OCCUPIED UNOCCUPIED OCCUPIED UNOCCUPIED 8 AM 6 PM 6 PM 6 PM 8 AM 70˚F (21˚C) 64˚F (18˚C) 72˚F (22˚C) 80˚F (27˚C) 8 AM 70˚F (21˚C) 64˚F (18˚C) 70˚F (21˚C) 64˚F (18˚C) 72˚F (22˚C) 80˚F (27˚C) 72˚F (22˚C) 80˚F (27˚C) You can use the table on the next page to plan your customized program schedule if using 5+1+1. Programming

The programmable fan feature will run the fan continuously during any time period it is programmed to be on. This is the best way to keep the air circulated and to eliminate hot and cold spots in your building. If using IAQ mode, set fan to IAQ for any time period. 1. Select HEAT or COOL with the SYSTEM key. Note: You have to program heat and cool each seperately. 2. Press the MENU button (If menu does not appear first press RUN SCHED). 3. Press SET SCHED. Note: Monday is displayed and the OCCUPIED text is shown. You are now programming the OCCUPIED time period for that day. 4. Time is flashing. Use the or key to make your time selection for that day’s OCCUPIED time period. Note: If you want the fan to run continuously during this time period, select ON with the FAN key. If you want to use IAQ mode during this time period, select IAQ with the fan key. 5. Press NEXT. 6. The setpoint temperature is flashing. Use the or key to make your setpoint selection for that day’s OCCUPIED period. 7. Press NEXT. 8. Repeat steps 4 through 7 for that day’s UNOCCUPIED time period. Monday: Repeat steps 4 through 8 for the remaining days of the week. To customize your 7 day 2 time period program schedule, follow these steps: Temporary Hold: The thermostat will display HOLD and RUN SCHED on the bottom of the screen when you press the or key. If you do nothing, the temperature will remain at this setpoint temporarily for 4 hours. The program setpoint will then replace the temporary setpoint. Permanent Hold: With a temporary hold set, If you press the HOLD key at the bottom of your screen, you will see HOLD appear below the setpoint temperature in the display. The thermostat will now permanently stay at this setpoint and can be adjusted using the or keys. To Return To Program: Press the RUN SCHED key at the bottom of the screen to exit temporary and permanent holds. Temporary & Permanent Hold Feature Custom Program Day of the Week Events Time Setpoint Temperature (HEAT) Setpoint Temperature (COOL) Weekday Saturday Sunday Wake/OCC1 Leave/UNOCC1 Return/OCC2 Sleep/UNOCC2 Wake/OCC1 Leave/UNOCC1 Return/OCC2 Sleep/UNOCC2 Wake/OCC1 LeaveUNOCC1 Return/OCC2 Sleep/UNOCC2 Occupied Unoccupied Occupied Unoccupied Occupied Unoccupied Set Program Schedule For Four Time Periods 1. Select HEAT or COOL with the system switch. Note: You have to program heat and cool each separately. 2. Press the MENU button (If menu does not appear first press RUN SCHED). 3. Press SET SCHED. Note: Monday-Friday is displayed and the WAKE/OCC1 icon is shown. You are now programming the WAKE/OCC1 time period for the weekday setting. 4. Time is flashing. Use the or key to make your time selection for the weekday WAKE/OCC1 time period. Note: If you want the fan to run continuously during this time period, select ON with the FAN key. If you want to use IAQ mode during this time period, select IAQ with the FAN key. 5. Press NEXT. 6. The setpoint temperature is flashing. Use the or key to make your setpoint selection for the weekday WAKE/OCC1 period. 7. Press NEXT. 8. Repeat steps 4 through 7 for the weekday LEAVE/UNOCC1 time period, for the weekday RETURN/OCC2 time period, and for the weekday SLEEP/UNOCC2 time period. To customize your 5+1+1 Program schedule, follow these steps: Weekday: Repeat steps 4 through 7 for the Saturday WAKE/OCC1 time period, LEAVE/UNOCC1 time period, RETURN/OCC2 time period, and for the Saturday SLEEP/UNOCC2 time period. Saturday: Repeat steps 4 through 7 for the Sunday WAKEOCC1 time period, LEAVE/UNOCC1 time period, RETURN/OCC2 time period, and for the Sunday SLEEP/UNOCC2 time period. Sunday: (WAKE, LEAVE, RETURN, SLEEP or OCCUPIED 1, UNOCCUPIED1, OCCUPIED 2, UNOCCUPIED 2) Programming

The control range of temperature.... 44˚F to 90˚F (7˚C to 32˚C) Load Rating............................................... 1 amp per terminal, 1.5 amp maximum all terminals combined Swing (cycle rate or differential) ...... Heating is adjustable from 0.2˚ to 2.0˚ Cooling is adjustable from 0.2˚ to 2.0˚ Power source ...........................................18 to 30 VAC, NEC Class II, 50/60 Hz for hardwire Battery power from 2 AA Alkaline batteries Operating ambient ............................... 32˚F to +105˚F (0˚C to +41˚C) Operating humidity .............................. 90% non-condensing maximum Dimensions of thermostat ................. 4.7” W x 4.3” H x 0.9” D Specifications Features If the filter change reminder is enabled, you will see a reminder in the display when your air filter needs changed. The reminder will be shown in the display after your system has run long enough to require an air filter change. Resetting The Filter Change Reminder: When the reminder is displayed, you should change your air filter and reset the reminder by holding down the 3rd button from the left side of the thermostat for 3 seconds. This thermostat also has other maintenance reminders (Humidity Pad, UV lamp, and IAQ Cell), that are reset with the same procedure. Filter Change & Other Reminders