Stanley CD12 Operation & User’s Manual
Text of the manual
© 2014 STANLEY Black & Decker, Inc.
New Britain, CT 06053
U.S.A.
62379 8/2018 Ver. 9
USER MANUAL
Safety, Operation and Maintenance
CD12
HYDRAULIC
CORE DRILL
CD12 User Manual ◄ 3
TABLE OF CONTENTS
SERVICING: This manual contains safety, operation and routine maintenance instructions. STANLEY Infrastructure
recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized
and certified dealer. Please read the following warning.
To fill out a product warranty validat
4 ► CD12 User Manual
Always observe safety symbols. They are included for your safety and for the protection of the tool.
LOCAL SAFETY REGULATIONS
Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and
maintenance personnel.
Safety symbols and signal words, as shown below, are used to emphasize all opera
CD12 User Manual ◄ 5
Tool operators and maintenance personnel must always
comply with the safety precautions given in this manual,
and on the stickers and tags attached to or on the tool
and hoses.
These safety precautions are for your safety. Review
them carefully before operating the tool or performing
any maintenance or repairs.
Supervising
personnel
ma
6 ► CD12 User Manual
SAFETY TAG P/N 15875 (Shown smaller then actual size)
D A N G E R
D A N G E R
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE
OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
SEE OTHER SIDE
1.
FAILURE TO USE HYDRAULIC HO
CD12 User Manual ◄ 7
The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the
hydraulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with
STANLEY hydraulic tools. They are:
Certifi ed non-conductive — constructed of thermoplastic or synthetic
8 ► CD12 User Manual
Oil Flow
Hose Lengths
Inside Diameter
USE
(Press/Return)
Min. Working Pressure
GPM
LPM
FEET
METERS
INCH
MM
PSI
BAR
Certifi ed Non-Conductive Hose - Fiber Braid - for Utility Bucket Trucks
4-9
15-34
up to 10
up to 3
3/8
10
Both
2250
155
Conductive Hose - Wire Braid or Fiber Braid -DO NOT USE NEAR ELECTRICAL CONDUCTORS
4-6
15-23
up to 25
CD12 User Manual ◄ 9
HTMA / EHTMA REQUIREMENTS
TOOL TYPE
HTMA
HYDRAULIC SYSTEM REQUIREMENTS
TYPE I
TYPE II
TYPE RR
TYPE III
Flow range
4-6 GPM
(15-23 LPM)
7-9 GPM
(26-34 LPM)
9-10.5 GPM
(34-40 LPM)
11-13 GPM
(42-49 LPM)
Nominal operating pressure
(At the power supply outlet)
1500 psi
(103 bar)
1500 psi
(103 bar)
1500 psi
(103 bar)
1500 psi
(103 bar)
System
10 ► CD12 User Manual
GENERAL OPERATION
Tools included are for mounting and dismounting:
•
Single-head wrench
SW 24
•
Single-head wrench
SW 32
•
Single-head wrench
SW 41
•
Hex wrench
SW 5
DRILL BIT INSTALLATION
Before changing the drill bit, ensure the tool is
disconnected from the hydraulic power source, to
avoid unintentional operation of the too