Xpresskit DBALL2-MRC01 Operation & User’s Manual

Text of Xpresskit DBALL2-MRC01 Operation & User’s Manual

Update Alert: Firmware updates are posted to the web on a regular basis. We recommend

that you check for firmware and/or install guide updates prior to installing this product. † Mercedes-Benz is registered trademarks and property of their respective companies. Vehicle Application Guide................................................................................................................................................ Installation Wiring

Vehicle Application Guide

* - available only in trigger or warning mode D: Data-to-Data (D2D) only •: D2D and Wire-to-Wire (W2W) AV: Horn & Lights Control CC: Comfort & Convenience Controls DL: OE Door Lock & Alarm Controls RS: Engine Start & Status SS: Entry Point Status-Security ST: Function/Feature Status 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 A-Class (W169) A A A A A A A A • • • • • • • D • • • D D A-Cl

Xpresskit DBALL2-MRC01 Installation Wiring Diagram

Security System 10 DBALL Programming button LED 1: Green: (-) Lock Input 2: Blue: (-) Unlock Input 3: Red/White: (-) Trunk Release Input 4: White/Violet: (-) AUX1 Input* 5: Violet/Black: (-) AUX2 Input* 4 TX (-) Ground RX (+)12v 14 12 2 (+) 12v 5: Orange/Green: FT CAN High 3: Tan/Black: HS CAN High 6: Orange/Brown: FT CAN Low 4: Tan: HS CAN Low 13: Red: (+) 12v 14: Black: (-) Ground 7: Gray/Black: (+) Ignition Output 12:

Xpresskit DBALL2-MRC01 Can Location for TYPE A

Can Location for TYPE B Mercedes C (up to 2007)/CLC/CLK Mercedes S/CL Class Mercedes C (2007 - up)/GLK Mercedes E (W212) Mercedes Sprinter Volkswagen Crafter Mercedes Vito/Viano Mercedes E (W211)/CLS Can H: Brown/Red Can H: Brown/Red Can H: Brown/Red Can H: Brown/Red Can H: Brown/Red Can L: Brown Can L: Brown Can L: Brown Can L: Brown Can H: Brown/Red Can H: Brown/Red Can H: Brown/Red Can L: Brown Can L: Brown Can L: Brown Ca

Turn ON Ignition using Key or

Push-to-Start (PTS) button. START STOP START STOP E E N N G I E E N N G I x2 x1 & & The LED turns ON solid green for 3 seconds, then turns OFF once the module has been successfully programmed. 3 5 1 4 R 2 Module reset will be done automatically upon programming. 3 1 Wait until the LED turns ON orange then release the Programming button. The LED turns ON red. Please ensure that the vehicle is i

Feature and Option List

To enter feature programming routine � Use the key to turn the ignition ON, then OFF. � Within 5 sec, press and HOLD the Programming button. The orange LED turns ON after 3 seconds. Release the Programming button. � The green LED starts flashing slowly one time to indicate the feature number is 1. After a short delay, the red LED flashes rapidly to indicate the current option of feature 1. It repeats until next action h

LED Diagnostics and Troubleshooting

LED Status Description Troubleshooting Solid red. Waiting for the vehicle to be started. Solid red for 30 seconds, then flashes once. Solid red for 30 seconds, then flashes twice. FT CAN not detected. HS CAN not detected. The CAN wires may be incorrectly connected. Refer to the wiring diagram to make the right connections. The CAN wires may

For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed

Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was pu

Xpresskit Automobile Accessories Owners Instructions: