ProSoft MVI69E-MBS Operation & User’s Manual

Communication Module June 28, 2017 USER MANUAL ...

We always want you to feel that you made the right decision to use our products. If you have suggestions, comments, compliments or complaints about our products, documentation, or support, please write or call us. ProSoft Technology 9201 Camino Media, Suite 200 Bakersfield, CA 93311 +1 (661) 716-5100 +1 (661) 716-5101 (Fax) www.prosoft-technology.com [email protected] MVI69E-MBS User Manual June 28, 2017 ProSoft Technology ...

North America Warnings A This Equipment is Suitable For Use in Class I, Division 2, Groups A, B, C, D or Non-Hazardous Locations Only. B Warning – Explosion Hazard – Substitution of Any Components May Impair Suitability for Class I, Division 2. C Warning – Explosion Hazard – Do Not Disconnect Equipment Unless Power Has Been Switched Off Or The Area is Known To Be Non-Hazardous. D The subject devices are powered by a Swi ...

Contents Modbus Serial Enhanced Communication Module User Manual ProSoft Technology, Inc. Page 5 of 154 June 28, 2017 Contents Your Feedback Please ........................................................................................................................ 2 Content Disclaimer .............................................................................................................................. 2 Impo ...

User Manual Modbus Serial Enhanced Communication Module Page 6 of 154 ProSoft Technology, Inc. June 28, 2017 4.3.2 Read Block: Response from the Module to the Processor ..................................... 65 4.3.3 Read and Write Block Transfer Sequences ........................................................... 66 4.4 Data Flow Between the Module and Processor ................................................ ...

Contents Modbus Serial Enhanced Communication Module User Manual ProSoft Technology, Inc. Page 7 of 154 June 28, 2017 7.2.9 Preset Single Register (Function Code 06) ........................................................... 112 7.2.10 Diagnostics (Function Code 08) ............................................................................ 113 7.2.11 Force Multiple Coils (Function Code 15) ........................... ...

Modbus Serial Enhanced Communication Module User Manual ProSoft Technology, Inc. Page 8 of 154 June 28, 2017 ...

Start Here Modbus Serial Enhanced Communication Module User Manual ProSoft Technology, Inc. Page 9 of 154 June 28, 2017 1 Start Here In This Chapter  System Requirements ........................................................................... 10  Deployment Checklist ............................................................................ 10  Package Contents ............................................. ...

User Manual Modbus Serial Enhanced Communication Module Page 10 of 154 ProSoft Technology, Inc. June 28, 2017 1.1 System Requirements The MVI69E-MBS module requires the following minimum hardware and software components:  Rockwell Automation CompactLogix or MicroLogix 1500-LRP® processor (firmware version 10 or higher), with compatible power supply and one free slot in the rack, for the MVI69E-MBS module. ...

Start Here Modbus Serial Enhanced Communication Module User Manual ProSoft Technology, Inc. Page 11 of 154 June 28, 2017 1.2 Deployment Checklist Before you begin to configure the module, consider the following questions. Your answers will help you determine the scope of your project, and the configuration requirements for a successful deployment.  Are you creating a new application or integrating the module into an ...

User Manual Modbus Serial Enhanced Communication Module Page 12 of 154 ProSoft Technology, Inc. June 28, 2017 1.4 Setting Jumpers When the module is manufactured, the port selection jumpers are set to RS-232. To use RS-422 or RS-485, you must set the jumpers to the correct position. The following diagram describes the jumper settings. Note: Jumper pin placement on the circuit board may vary. The Setup Jumper ...

Start Here Modbus Serial Enhanced Communication Module User Manual ProSoft Technology, Inc. Page 13 of 154 June 28, 2017 The following illustration shows the MVI69E-MBS jumper configuration, with the Setup Jumper OFF. 1.5 Installing the Module in the Rack Make sure the processor and power supply are installed and configured before installing the MVI69E-MBS module. Refer to the Rockwell Automation product documentation f ...

User Manual Modbus Serial Enhanced Communication Module Page 14 of 154 ProSoft Technology, Inc. June 28, 2017 1 Align the module using the upper and lower tongue-and-groove slots with the adjacent module and slide forward in the direction of the arrow. 2 Move the module back along the tongue-and-groove slots until the bus connectors on the MVI69 module and the adjacent module line up with each other. ...

Start Here Modbus Serial Enhanced Communication Module User Manual ProSoft Technology, Inc. Page 15 of 154 June 28, 2017 3 Push the module’s bus lever back slightly to clear the positioning tab and move it firmly to the left until it clicks. Ensure that it is locked firmly in place. 4 Close all DIN-rail latches. ...

User Manual Modbus Serial Enhanced Communication Module Page 16 of 154 ProSoft Technology, Inc. June 28, 2017 5 Press the DIN-rail mounting area of the controller against the DIN-rail. The latches momentarily open and lock into place. ...

Adding the Module to RSLogix Modbus Serial Enhanced Communication Module User Manual ProSoft Technology, Inc. Page 17 of 154 June 28, 2017 2 Adding the Module to RSLogix In This Chapter  Creating the Module in an RSLogix 5000 Project .................................. 17  Installing ProSoft Configuration Builder ................................................. 24  Generating the AOI (.L5X File) in ProSoft Conf ...

MVI69E-MBS ♦ CompactLogix Platform User Manual Modbus Serial Enhanced Communication Module Page 18 of 154 ProSoft Technology, Inc. June 28, 2017 2.1.1 Creating a Module in the Project Using an Add-On Profile Installing an Add-On Profile Download the AOP file (MVI69x_RevX.X_AOP.zip) from the product webpage (www.prosoft-technology.com) onto your local hard drive and then extract the files from the zip archive. Make sure you ha ...

Adding the Module to RSLogix Modbus Serial Enhanced Communication Module User Manual ProSoft Technology, Inc. Page 19 of 154 June 28, 2017 3 Click FINISH when complete. The AOP is now installed in RSLogix 5000. You do not need to reboot the PC. Using an Add-On Profile 1 In RSLogix 5000, expand the I/O CONFIGURATION folder in the Project tree. Right-click the appropriate communications bus and, and then click NEW MODULE. ...

MVI69E-MBS ♦ CompactLogix Platform User Manual Modbus Serial Enhanced Communication Module Page 20 of 154 ProSoft Technology, Inc. June 28, 2017 This opens the Select Module Type dialog box. In the Module Type Vendor Filters area, uncheck all boxes except the PROSOFT TECHNOLOGY box. A list of ProSoft Technology modules appears in the dialog box. 2 Select the MVI69E-MBS module in the list and click CREATE: ...