Crestron Zum Installation Manual

Installation Guide Description The Crestron® ZUMMESH NETBRIDGE enables Zūm device setup from a mobile app and integrates a stand-alone Zūm lighting control system with the Zūm hub (sold separately) for a centrally managed, enterprise-wide lighting control system. Attach the Network Bridge to a Zūm J-box device (sold separately) to use the mobile app to set up the Zūm devices in the room. Adding the Zūm hub to the centrally-managed lighting system enables all of the network bridges to interface for centralized monitoring, management, and control of the lighting systems throughout an entire building. A basic single-room Zūm system consists of Zūm mesh devices, i.e., dimmers, switches, keypads, and sensors. The Zūm mesh devices in the room communicate directly with each other without the need for a centralized gateway or processor. Additional Resources Visit the product page on the Crestron website (www.crestron.com) for additional information. Use a QR reader application on your mobile device to scan the QR image. Installation WARNING: To avoid fre, shock, or death, turn off the power at the circuit breaker or fuse and test that the power is off before wiring! NOTE: Install and use this product in accordance with appropriate electrical codes and regulations. NOTE: Ensure that the ZUMMESH-NETBRIDGE is installed within range of the ZUMNET-GATEWAY. Mount the ZUMMESH-NETBRIDGE to any J-box device. 1. Use a fat-head screwdriver to remove the cover on the J-box device. 2. Align the ports on the ZUMMESH-NETBRIDGE and the J-box device, and then insert the network bridge into the J-box device. The network bridge snaps into place. Neutral (white) Hot (black) 100-277 Vac power from breaker Remove the network bridge. 1. Place your thumb on the side of the network bridge that is nearest the J-box. 2. Press the network bridge away from the J-box. While pressing on the side of the network bridge, slightly lift your thumb up. The network bridge should easily detach from the J-box device. Using the Zūm App The Zūm app is available for download from the App Store® app in iTunes® software. The Zūm app provides quick and easy setup of a Zūm network. SPECIFICATION DETAILS Power Requirements Average Draw 60 mA, 3.3 Volts Peak Draw 250 mA, 3.3 Volts Power provided via the ZUMMESH-JBOX or ZUMMESH-JBOX-PSU (sold separately) Enclosure Housing Plastic, white Mounting Mounts to a Zūm J-Box Zone Controller or a Zūm Network Bridge Power Supply (sold separately); Plenum rated for mounting in air-handling space Environmental Temperature 32° to 104 °F (0° to 40 °C) Humidity 10% to 90% RH (noncondensing) Dimensions Height 1.66 in (42 mm) Width 1.94 in (49 mm) Depth 0.76 in (20 mm) Weight 3 oz (85 g)

Laboratories Inc. Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifcations not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Industry Canada (IC) Compliance Statement CAN ICES-3(A)/NMB-3(A) The product warranty can be found at www.crestron.com/warranty. The specifc patents that cover Crestron products are listed at patents.crestron.com. Certain Crestron products contain open source software. For specifc information, please visit www.crestron.com/opensource. Crestron, the Crestron logo, and Zūm are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. App Store and iTunes are either trademarks or registered trademarks of Apple, Inc. in the United States and/or other countries. UL and the UL logo are either trademarks or registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. This document was written by the Technical Publications department at Crestron. ©2017 Crestron Electronics, Inc. Crestron Electronics, Inc. Installation Guide - DOC. 7955A 15 Volvo Drive Rockleigh, NJ 07647 (2048126) Tel: 888.CRESTRON 02.17 Fax: 201.767.7576 Specifcations subject to www.crestron.com change without notice. Connect the Network Bridge to the Zūm System Adding the network bridge converts a stand-alone Zūm lighting control system for a single room into a centrally controlled, networked system. The ZUMMESH-NETBRIDGE communicates with the ZUM-FLOOR-HUB via a ZUMNET-GATEWAY. This connection is made via a wireless communications protocol. To join or leave the ZUM-FLOOR-HUB system, use the procedures outlined below. Connecting the ZUMMESH-NETBRIDGE to the ZUMNET-GATEWAY In order for the ZUM-NETBRIDGE to communicate to the ZUM-FLOOR-HUB, it must frst connect to a ZUMNET-GATEWAY. NOTE: The ZUM-NETBRIDGE can be acquired by only one ZUMNET-GATEWAY. 1. Press the ACQUIRE button on the ZUMNET-GATEWAY to allow the ZUMMESH-NETBRIDGE to join the system. Refer to the ZUMNET-GATEWAY’s manual at www.crestron.com/manuals for details. NOTE: In an environment where multiple ZUMNET-GATEWAYs are installed, only one should be in Acquire mode at any time. 2. Connect the ZUMMESH-NETBRIDGE to the ZUMNET-GATEWAY. a. Tap the SET button on the ZUMMESH-NETBRIDGE three times, and then press and hold it down (tap-tap-tap-press+hold) until the red LED on the device blinks once (this can take up to 10 seconds). 2s or 10s b. Release the SET button to start the acquire process. The red LED blinks slowly to show that the device is attempting to connect to the ZUMNET-GATEWAY. • The LED turns on for 5 seconds to show that the ZUMMESH-NETBRIDGE has joined the network. • The LED blinks fast to indicate that the ZUMMESH-NETBRIDGE failed to join the network. Press the SET button to acknowledge the failure. Make sure that the ZUMNET-GATEWAY is within range and repeat steps 1 and 2. 3. Once all ZUMMESH-NETBRIDGE has been acquired, press the ACQUIRE button to take the ZUMNET-GATEWAY out of Acquire. Refer to the ZUMNET-GATEWAY’s manual for details. Disconnecting the ZUM-NETBRIDGE from the ZUMNET-GATEWAY To leave the network, put the ZUM-NETBRIDGE into Acquire mode, as described in the section above, when no ZUMNET-GATEWAY is in Acquire mode. Verifying Communications Status To check the communications status of the device, tap the SET button three times, and then press and hold it down (tap-tap-tap-press+hold) for up to 2 seconds. The LED blinks to indicate the communications status. Refer to the following table for details. LED COMMUNICATIONS STATUS Turns on for 5 seconds The device is communicating with the ZUMMESH-FLOOR-HUB. Blinks three times The device is communicating with the gateway, but the gateway is not communicating with the ZUMMESH-FLOOR-HUB. Blinks twice The device was previously joined to the network but is not communicating with the gateway. Blinks once The device is not joined to the network.