Black Box LB510A Operation & User’s Manual
Read Online
Read the Black Box LB510A Operation & User’s Manual online using the built-in PDF viewer.
Key Pages of Document
FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018 Web site: www.blackbox.com • E-mail: [email protected] G.SHDSL NTU DECEMBER 2006 LB510A ...
All applied-for and registered trademarks are the property of their respective owners. • The LB510A contains no user serviceable parts. The equip- ment shall be returned to Black Box for repairs, or repaired by qualified service personnel. • An approved external power supply that incorporates a disconnect device shall be used and positioned within easy reach of the operator. • For AC powered units, the po ...
Your NTU comes with an external AC adaptor with detachable power cord. 1.1 AC power-up 1. Connect female plug of the AC power cord to the AC adaptor provided. 2. Connect the barrel-type connector of the AC adaptor to the barrel-type power jack on the LB510A. 3. Insert the male plug of the AC power cord into an AC power outlet (100– 240 VAC). 1.2 Power-up indication The Power and 100M Ethernet LEDs are lit whi ...
The LB510A is shipped with a factory-configured IP address assigned to the Ethernet LAN port (green outline). The address is 192.168.200.10/24. In most cases, you must change the address to be on the same subnet as your PC, as described in the procedures below. If you are not sure which IP address to use for your installation, contact your network administrator. 2.3 Connect a PC and log in 1. Using the incl ...
1.
Display current IP interface settings for the LB510A Ethernet LAN port.
ip list interfaces
Now you can connect the LB510A to your local IP network and complete the remaining configuration from your PC using a standard web browser. Connect the LB510A’s Ethernet port (green) to the same Ethernet segment as your PC (see Figure 2). The front-panel Ethernet Link LED should turn on. If it does not, press the rear-panel MDI-X switch so that the Ethernet Link LED illu- minates. You can check the conn ...
You will now access the web management graphical user interface (GUI) to con- figure the LB510A using a standard web browser (such as Netscape browser or Internet Explorer). 1. At your PC, open a web browser and enter the IP address you assigned to the LB510A’s Ethernet LAN port in step 2 of section “Modify the IP address” on page 5. (In this example, 10.10.4.10.) 2. Log in to the web ma ...
1. Obtain single-twisted-pair cable with an RJ-11 plug connector at each end. 2. Plug one end of the cable into the (yellow) RJ-11 socket (labelled Line) on the LB510A. 3. Plug the other end of the cable into the RJ-11 wall socket that provides your G.SHDSL service. 4. Go to G.SHDSL > Configuration to configure the DSL port parameters. Note If two LB510As are connected back-to-back, one must be con� ...
A.1 Radio and TV Interference (FCC Part 15) This equipment generates and uses radio frequency energy, and if not installed and used properly—that is, in strict accordance with the manufacturer's instruc- tions—may cause interference to radio and television reception. This equipment has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpar ...
the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, opera- tions or procedures that could affect the operation of the equipment. If this hap- pens, the telephone company will provide advance notice in or ...
Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate this product from other waste and scrap and deliver to the WEEE collection system in your country for recycling. ...
1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746 ...
