Xpresskit DBALL Installation Manual

Text of Xpresskit DBALL Installation Manual

Xpresskit DBALL Vehicle Application Guide................................................................................................................................................

Key2GO........................................................................................................................................................................... Installation (Wiring Diagrams & Vehicle Wiring Reference Charts) Without T-Harness..............................

© 2016 Directed. All rights reserved.

Vehicle Application Guide Page 2 The table below lists the vehicles and features which are compatible with this product. Refer to the following pages for more information on installation wiring, programming and troubleshooting for these vehicles. Vehicles 2016 2015 2014 2013 PK-Immobilizer Bypass-Data No Key Req'd AV-Parking Lights Control CC-Heated Mirrors CC-
© 2016 Directed. All rights reserved. This feature is mandatory to control the immobilizer override in this firmware. Key2GO has been designed and developed to bypass the advanced encryption layers found in modern vehicles. It uses an array of servers to generate a duplicate of the original key, allowing the installation of a remote starter without having to give up a key. The advantage is that thi
© 2016 Directed. All rights reserved. Page 4 [1] (AC) Tach Input (-) Trunk Status Input (-) Door Status Input Remote Starter (-) GWR (Status) (-) Lock Output (+) Starter Output (-) Unlock Output (-) Trunk Output (+) Parking Lights Output (+) Brake Input (-) E-Brake Status Input 10 RF LED 4 TX (-) Ground RX (+)12V 14 12 2 Immo. Data (conn. side): Yellow: 8 Immo. Data (veh. side): Orange/Yellow: 9 Ig
© 2016 Directed. All rights reserved. Installation with T-Harness THCHD3 OBDII OBDII Diagnostic 16-pin Connector (vehicle side) Keyless Ignition Node NOT Used OBDII OR OBDII Diagnostic 16-pin Connector (vehicle side) These T-Harness connectors are NOT interchangeable. They will fit ONLY the appropriate vehicles. T-01 T-02 The Remote Start Safety Override Switch MUST be in the ON position. Remote St
© 2016 Directed. All rights reserved. Vehicle Wiring Reference Chart Function Color Pin Polarity Location Color Pins 12V Red A or 16 (+) C1 conn. at BCM located under driver dash or at OBDII Diagnostic conn. Gray 2 or 16 Brake Dk. Green/Lt. Green 1 (+) Brake switch. White 4 Immo Data White/Lt. Green 5 Data Push-to-Start switch. Black 6 Push-To-Start Violet/Brown 4 (+) Push-to-Start switch. Black 6
© 2016 Directed. All rights reserved. Page 7 1 Solid Wait until the LED turns ON solid red. Remove the battery from the factory keyless remote & Open and remove battery PANIC x2 x2 PANIC x2 x2 6 Disconnect the module and complete the Key2GO programming. 2 Use the tip of the remote to press on the Start/Stop button (PTS) twice to turn the ignition ON ("RUN" illuminates on Start/Stop switch). The LED
© 2016 Directed. All rights reserved. Page 8 You have successfully completed the module programming sequence. 3 2 1 Once the configuration is completed, reconnect the module. The LED turns ON solid green for 3 seconds, then turns off. Click on Submit Key2GO Request. Remove the module from the vehicle and reconnect it to your computer. The web site will automatically recognize that you are moving on
© 2016 Directed. All rights reserved. 2 Solid & Solid Flashes & Release 3 Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red. Release the programming button. The LED turns ON solid red. Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installati
© 2016 Directed. All rights reserved. Page 10 Feature and Option List It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. The web offers more options; however, manual configuration of the features is possible using the information on this page. * Default option Feat. Operation Flashes / Optio
© 2016 Directed. All rights reserved. To enter feature programming routine - Turn the ignition ON, then OFF. - Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the Programming button. - The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate the current opti
© 2016 Directed. All rights reserved. Page 12 LED Diagnostics & Troubleshooting LED Description Troubleshooting Module has no power. Make sure the D2D harness is connected or that the 12 Volt is present between the red and black wires. If the 12 Volt is present, the module may be defective. Waiting to begin the programming sequence. Ensure the correct programming procedure is being followed. CAN pr
© 2016 Directed. All rights reserved. Limited One Year Consumer Warranty Page 13 For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”),

Stop the vehicle in a safe parking spot

and put the gear in Park (P). Press remote start button [1] [1] Your aftermarket remote may differ from the model shown in the illustrations. Stop & put vehicle in Park (P) P & Exit vehicle with Smart Key Quick Reference Guide DBALL/DBALL2-CHRYSLER7 © 2016 Directed. All rights reserved. Pit Stop Mode The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine run

Xpresskit DBALL Quick Reference Guide

DBALL/DBALL2-CHRYSLER7 © 2016 Directed. All rights reserved. Button(s) Actions Press & hold for 1 second to lock. Press & hold for 1 second to unlock. Press & hold for 1 second to remote start. Press & hold for 5 seconds to activate the trunk release (optional). Press once, then to activate the rear hatch/tail glass release (optional).* Press 3 times, then to activate the panic mode. Press once, then

Xpresskit Automobile Accessories Owners Instructions: