Gehl HL 360 Operator's Manual
Read Online
Read the Gehl HL 360 Operator's Manual online using the built-in PDF viewer.
Key Pages of Document
Gehl Company (Incorporated), hereinafter referred to as GEHL, as manufacturer of quality machinery since 1859, warrants new GEHL machinery and/or attachments at the time of delivery to the original purchaser, to be free from defects in material and workmanship if properly set up and operated in accordance with the recommendations set forth in the GEHL Operators Manual. GEHL's liability for any defect with ...
You have made a sound and lasting investment. Gehl Company has been building quality equipment for well over a century. Our entire manufacturing and marketing philosophy is built upon quality. The quality built into Gehl products assure you the performance and reliability you need to make a profit. Your authorized Gehl Skid Steer Loader dealer is equipped to service your Geh ...
3.6 (0.1) 4.6 (0.13) 42" Utility Bucket 4.3 (0.12) 5.4 (0.15) 42" Light Material Bucket 7.7 (0.215) 9.8 (0.275) 48" Light Material Bucket 8.8 (0.245) 11.4 (0.32) 60" Light Material Bucket 11.0 (0.31) 14.5 (0.41) 36" Manure Fork 42" Manure Fork 36" Pallet Fork Accessory ............. Weld-on Grapple Attachment KEY TO ILLUSTRATION Dimensions in Inches (Millimeters) A. Overall Maximum Height - Buc ...
DELIVERY CHECK LIST The following Check List is an important reminder of The following Check List is an important reminder of valuable information and inspections which MUST be valuable information that MUST be passed on to the made before delivering the unit to the Customer. Check Customer at the time the unit is delivered. Check off each off each item after prescribed action is taken. item as you explain it to the Customer. ...
DELIVERY CHECK LIST The following Check List is an important reminder of valuable information and inspections which MUST be made before delivering the unit to the Customer. Check off eaGh item after prescri bed action is taken. Check that : __ Unit is NOT damaged in shipment. Check for such things as dents and loose or missing parts; correct or replace components as required . __ Fuel Tank, Fuel Lines and Fittings are NOT dama ...
EQUIPMENT, READ AND STUDY THE FOLLOWING SAFETY INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THIS EQUIPMENT, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFETY PRECAUTIONS. Gehl Company always takes the operator and his safety into consideration when designing farm machinery and guards exposed moving parts for his protection; however, some areas cannot be guarde ...
on a regular routine basis; escaping fluid under pressure can cause serious injury! ALWAYS wear a hard hat when operating the Skid Steer Loader! Refuel in a safe place away from open flames and potential sparks, NEVER refuel the Loader when the engine is hot! NEVER refuel with Loader engine running! The Hydrostatic Drive of a Skid Steer Loader operates with Oil Flow. When the Pump is NOT operating the Loade ...
Agricultural Engineers, has adopted as a SAFETY ALERT SYMBOL. When you see this symbol, in this manual or on the unit itself, you are reminded to BE ALERT! Your Safety is involved. CONTROLS & SAFETY EQUIPMENT Whenever and wherever possible and without affecting machine operation, Guards and Shields have been used on this equipment to protect potentially ...
SEAT BELT (Fig. 4) A WARNING: When it becomes necessary to work on the Loader with the Load Arms raised, BE SURE to engage the Lift Cylinder Lock BEFORE shutting the engine off and leaving the Operator's Compartment. The Lift Cylinder Lock is located on the right Lift Cylinder. Both the "engaged" and "storage" positions of the Lock are shown. Secure the Lock in the "storage" position with the Lockpin provided. Refer to Ope ...
HOURMETER (Fig. 5) unathorized engine starting, especially while performing service, BE SURE to For added convenience in proper routine maintenance performance, an Hourmeter is provided to automati remove the Key BEFORE leaving the Operator's Compartment. . cally record engine running time. Refer to the Maintenance Schedule in the back of this manual for THROTTLE (Fig. 5) Engine RPM is varied with a hand-operated Throt ...
5. Disengage the Hydrostatic Pump Drive Belt Idler. 6. Turn the Ignition Key to "OFF" and remove the Key. 7. Make sure that all movement and Loader motion has stopped, detach the Seat Belt and climb out of the Operator's Compartment. BEFORE STARTING THE ENGINE Before actually starting the engine and running the Loader, familiarize yourself with the T -bar operation to orient your mind and coordinate your hand move ...
Engaging Lock Before proceeding to engage the Lift Cylinder Lock and to prevent Loader movement, first disengage the Hydro static Pump Drive Belt Idler. 1. Remove the Lockpin from the Cylinder Lock. 2. Raise the Load Arms far enough to allow the Lock to drop down around the Cylinder Rod. 3. Lower the Load Arms slightly until the Lock firmly rests against the Cylinder. NOTE: DO NOT drop the Load Arms onto the � ...
• 2-Spool Control Valves do NOT have a Lift/Tilt T-bar Float Position NOR Auxiliary Hydraulics connections. Digging & Loading (Figs. 9, 10, 11 & 12) To dig with and load the Bucket, first lower the Load Arms down in contact with the Loader Frame and roll the Bucket Cutting Edge down in contact with the ground. Move the Loader into the material and, as the engine RPM loads-down, roll the Bucket back slowly and, at ...
S \ , , \ \,... - ."" '- ""~ \ , . \. ... ....._----_.__ .. _-_.. __ .' I..L_' ~" _'''' •••• Fig.11 Dumping the Bucket or Fork Onto a Pile Carry the loaded Bucket or Fork low until reaching the pile. Then, stop forward motion and raise the Load Arms high enough so that the Bucket or Fork clears the top of the pile. Then, slowly move the Loader ahead to position the Bucket or ...
Both HL360 Skid Steer Loader models, units with either 2-Spool or 3-Spool Control Valves, can be used for scraping with a Bucket attached to the Load Arms. For scraping, the Loader should be operated in the forward direction. First position the Load Arms at the appropriate level which allows the Bucket to be tipped to place the Bucket Cutting Edge at a slight angle to the surface being scraped. While traveling forward ...
, :: ~" ~q; , ." : \~ i~ :,~' : ~ \ \~ ~ :."......... ~ : .~: , ~ \ \ ..... \ ~',~}': : : ~ : , ~. \ :'~" : .\' "'\ \ 1", ,\ , , \ \ \ , \ , \ , \ , \ , , , , , ~ ~,.. '.'"'' s \ : \,,~..." ......."'~ \ , ' \ ~~~~ ... -.~~~~,........... ~ ..\ l"_; ~\.....·' Fig. 15 Bucket and Fork Mounting (Figs. 16 & 17) HL360 Buckets and Forks are designed for quick and convenient attachment ...
WARNING: The above procedure for raising minimum amount of readjustment required to maintain the Loader should only be used for just that. proper Loader operation. DO NOT leave the Operator's Compartment NOTE: If the Loader is operated on a "day-to • day" basis and since NO gasoline gauge is provided, it is advisable to refuel before starting the day. A WARNING: Refuel in a safe place a ...
NOTE: Replace the Hydrostatic/Hydraulic Oil • Skid Steer Loader with the engine running. and Filter after the first 10 hours of operation Remove the Ignition Key to prevent unauthorized or unexpected starting. NOTE: Log the date of Lubrication in the Main • tenance Schedule. GENERAL INFORMATION NOTE: Properly lubricate the entire Loader • and replace engine 011 after the first 25 hours of operat ...
