Formax FD 332 Operator's Manual

enables users to achieve greater efficiency at work by releasing them from paper-folding that has manually been performed in the past. Please read the Operation Manual carefully before using this machine. Contents Introduction .............................................................................. 1 Contents ................................................................................... 1 (1) Specifications ....................................................................... 2 (2) Accessories .......................................................................... 3 (3) Description of Parts ............................................................... 4 (4) Designation and Functions of Operation Panel........................... 5 (5) Preparation .......................................................................... 6 (6) Operation Procedure.............................................................. 7 Switching the Power on ......................................................... 7 Setting Fold Plate Positions .................................................... 7 Test Folding ......................................................................... 8 Fold Feed Angle/Skew Adjustment .......................................... 8 Continuous Folding ............................................................... 8 Batch Counting .................................................................... 9 Clearing a Paper Jam .......................................................... 10 Cross Folding ..................................................................... 10 Fine Adjustments for Table 1................................................ 12 Fine Adjustments for Table 2................................................ 13 (7) Daily maintenance .............................................................. 14 (8) Trouble shooting ................................................................. 15

Smaller size is for single fold only. Paper quality High-quality paper, high-quality paper for stencil printing, medium-quality paper Fold type Single, Letter, Zigzag, Double, Parallel Fold-out Other special folding twice. Maximum Table 1: 13” Table 2: 9 ½” Fold dimensions Minimum Table 1: 2” Table 2: 1 ½” Paper feed system Three-roller paper feed system Max. stacking capacity 500 sheets 20# Folding speed 10500 sheets/hr (11” Half Fold) Operation method Pressing digital keys Available functions Fold skew adjustment, paper jam detection, four digit counter, auxiliary paper guide for cross folding and Jam map indication Power Consumption 75 W

addition/subtraction modes, and automatic paper size detector Auxiliary paper guide for cross fold A perforator can be installed (optional) Dimensions W 29 ½” x D 21 ½” x H 21” (during use) W 22” x D 21 ½” x H 21” (during storage) Net weight 80lb (2) Accessories Make sure that the following accessories are included in the package after opening it. Contact your sales agency immediately if there are missing accessories. Accessories Qty Illustration Table 1 1 Table 2 1 Power cable 1 Paper support guides (right and left) 2 Machine cover 1 Operation Manual 1

11 Control panel 3 Paper feed roller 12 Paper feed table 4 Paper guide 13 Table 2 5 Auxiliary feed table 14 Right side cover 6 Paper eject roller 15 Paper feed table lever 7 Paper stacking table 16 Power source switch 8 Stopper plate 17 Inlet 9 Fold position adjustment knob 18 Circuit breaker (4)Designation and Functions of Operation Panel

2 Start/Stop key Operation starts and if pushed again, The machine stops. 3 Clear/Reset key Clearing the indication of the counter / resetting an error. 4 Numerical key Used for batch counting. 5 Counter The number of sheets folded. 6 Check lamp Comes on when paper stock runs short, or indicates a place where paper feed trouble occurs.

Insert Table 1 on the studs indicated by (a) and (b) as shown in the picture to the right. Insert Table 2 on the studs indicated by (c) and (d) as shown in the picture to the right. Note: When setting Table 1, be sure to put its stopper plate at the center position. Caution: Be sure that both Table 1 and 2 properly fit in the positions of the studs (a), (b), (c) and (d). If they are improperly set, it may cause an incorrect collation, or the tables may fall out of the machine. Setting Paper: Lift the auxiliary table and pull the paper stacking table out. Raise the paper feed table lever.

Neatly stack the paper on the feed table with its printed side facing up. (its printed side down in case of fold-out) Lower the paper feed table lever to set the paper. Note: If the paper does not come in contact with the paper feed roller, remove and reinsert. Curled or wrinkled paper, may cause trouble. Correct it before use. In case of printed paper, use it only after the ink is dry, otherwise the paper feed rubber roller, paper separator, fold roller, and other parts of the unit will be stained with ink, causing trouble. Setting the paper discharge roller: The discharge roller should be moved to the proper position that suits the paper size. Note: Refer to the “Roller position indication” label. If ejection is not performed properly, set to a different position. Example: Set the roller to position one when using 8 ½” x 11” paper. (6)Operation Procedure Roller position indication label

Insert the power plug into the outlet. Set the POWER to ON position. Note: Remove the power plug from the outlet after use. Setting Fold Plate Table Position Pull the half-nut lever to move the stopper plate to the desired position on table 1 and 2. Align the arrow on the stopper plate with the desired fold marks on the tables and release the half-nut and the stopper plate will be locked in position. Test Folding Press the Test key to feed two sheets of paper. Check if the paper has been folded correctly by examining the second of the two folded sheets. If the fold position is not correct, refer to “Fine Adjustments” pages 11 & 12 Half nut lever

Turn the feed angle adjustment knob to the right if the lower side of the folded paper slants to the right. Turn the knob to the left of the lower side slants to the left. Note: In cases other than single fold, put the folded paper face down on Table 1 to make a feed angle adjustment. Continuous Folding: Press the Start/Stop key. The machine starts to fold the sheets continuously. Press the Start/Stop again, while the machine is in operation, to stop feeding. Batch Counting: As a sheet is folded the number indicated decreases by one. Feed angle adjustment knob

number of forms to be folded. Example: press the number “10” key twice to select twenty. Note: The batch counting number is cancelled when the POWER is set to OFF. Under the following conditions the machine will automatically stop feeding: (Press the Clear/Reset key to reset after the error has been corrected) Conditions Indication on Control panel 1. When the Start/Stop key is pressed while there is no stock. 2. When the Start/Stop key is pressed while the paper feed lever is at the upper position. 3. When the stock runs short while folding in the Batch Counting Mode. 1. When paper feed slip occurs 2. When paper jam occurs at Table 1 and Table 2 1. When paper stack table is full. 2. When paper jam occurs at the paper discharge. Clearing a Paper Jam: Numerical Key

jammed sheets. When the jammed paper is stuck around the fold roller or other parts, it can be easily removed by detaching the Table 1 and 2 from the unit. Note: When the roller cover is opened, the machine will stop operation instantly. Cross Folding: Cross folding refers to performing the double parallel, letter, or other types of folds for the sheets of paper folded using the single fold method. Example: 11”x 17” folded in half and then letter folded to fit into a standard # 10 envelope.

cross folding is 28#. This requirement, however, varies according to the following conditions: Paper type; Paper size; Whether grains run lengthways or sideways; Temperature and relative humidity; Printing condition. The folding position may be displaced to a greater extent than when the paper is folded using a regular fold method, or a corner of the folded paper may be folded inside as indicated in the figure. These, however, do not mean that the machine has broken down. Note: Press the crease hard using the hand. Do not stack too many sheets of paper on the paper feed table. Fine Adjustments for Table 1 Fold type Plane (A) Direction to turn the Table 1 fine adjustment knob Single fold Table 1 is not used Long Gate fold Short

Fold type Plane (B) Direction to turn the Table 2 fine adjustment knob Long Single fold Short Gate fold Long

1 Before cleaning the machine, be sure to set POWER is in the OFF position and pull the power plug from the outlet. 2 When the unit is not in use, put its cover in place to prevent dust, paper chips, etc. to accumulating on the paper fold rollers. 3 If paper chips, ink, etc. are accumulated on the paper fold rollers; it may cause trouble such as wrinkles, or improper folding. To prevent from it, clean them periodically.

separator, paper feed performance deteriorates and the machine becomes liable to paper jam or slip. Clean the rollers periodically to reduce down time. 5 If black marks occur that correspond with the location of the paper-feed tires, the feed tires need to be cleaned. 6 Consumable products: Paper feed rubber roller, rubber brake, and paper feed separator.

Trouble Possible Cause Measures Paper sticks just after it is printed Jog the paper sufficiently or feed the paper after it is dry. Stains on the paper separator Clean the paper feed separator using approved cleaner. Stains on the paper feed rubber roller. Clean the paper chips or ink on the paper feed roller with approved cleaner. The paper separator is worn out. Replace the paper separator with a new one. The paper does not feed properly The volume of the paper stacked on the paper feed table is not enough. If the volume on the paper feed table is not enough, it does not feed since the paper detection lever is installed. Stack 20 sheets or more. The machine does not operate even after the Start/Stop key is pressed. Paper jam inside the unit. Detach Table 1 and 2 and remove the paper in the unit. Paper sticks just after it is printed Jog the paper sufficiently or feed the paper after it is dry. Stains on the paper separator Clean the paper separator using the approved cleaner. Stains on the paper feed roller Clean the paper chips or ink on the paper feed roller with the approved cleaner. Stains on four paper fold rollers Clean the stain on four fold rollers using approved cleaner. Table 1 and 2 are not properly set. Reset properly. Wrinkles appear on the paper. Paper jam in Table 1 and 2 Detach Table 1 and 2 and remove the jammed paper out. Improper fold position The total length of the paper is not standard size. Measure the total length of the paper and adjust using the fine adjustment knob

are stained with paper chips or ink (slippery situation) Clean away the stain on four fold rollers using the approved cleaner. Drawing paper 13# or lighter cannot be folded. Low room temperature The paper gets stiff and hard to fold at the low room temperature in winter. Perform folding after leaving the paper as it is for 3 to 4 hours at the temperature of 53 to 67°F.