FIORENTINI N45E Operator's Manual

INSTRUCTION MANUAL. ING. O. FIORENTINI S.R.L. INDUSTRIAL CLEANING MACHINES ...

pag. 3 INTRODUCTION 3 TECHNICAL DESCRIPTION 4 GENERAL INFORMATION 5 MANUFACTURER RESPONSABILITY 5 INTERVENT REQUEST 5 TRANSPORTATION 6 HANDLING OF PACKED MACHINE 6 UNPACKING THE MACHINE 6 HANDLING OF UNPACKED MACHINE 6 OPERATORING CONTROLS 7 DASHBOARD CONTROLS 7 DASHBOARD SYMBOLS 7 USE OF THE MACHINE 8 CHOOSING THE DETERGENT SOLUTION 8 SCRUBBING 8 WATER FILLING AND DISCHARGE, TANK CLEANING 8 SQUEEGEE ADJUSTMENT 9 BRUSH ...

DUE TO TRANSPORT AND CHECK TO HAVE RECEIVED ALL THE SHOWING ON THE DOCUMENTS. IN CASE OF DAMAGES OR MISSING PART PLEASE ADVISE IMMEDIATELY THE MANUFACTURER INTRODUCTION THIS KIND OF SCRUBBER MACHINE ALLOWS THE OPERATOR TO CLEAN ALL KIND OF FLOOR AND ALL KIND OF DIRTY ,GIVING THE BEST RESULT. YOU CAN REACH BEST PERFORMANCES USING THE M ...

500 mm 650 mm HEIGHT 1000 mm 1000 mm N° BRUSHES 1 1 BRUSH SIZE ∅460 mm ∅530 mm WORK WIDTH 460 mm 530 mm SQUEEGEE WIDTH 800 mm 800 mm SOLUTION TANK IN POLYETHYLENE 65 liters 65 liters RECOVERY TANK IN POLYETHYLENE 55 liters 55 liters FRONT WHEEL DIAMETER 200 mm 200 mm REAR WHEEL DIAMET ...

accidents, etc.due to the non-acquaintance (or non-fulfilment) of the prescriptions contained in this manual .The same applies to change’s execution, modifications, and/or to the installation of accessory not preliminarily authorized. In particular the firm ING FIORENTINI SRL is not responsible for any damages caused ...

The machine is supplied packed on pallet, closet in a box made of plywood or paper board. The weight and sizes are showed in the normal characteristics. The barycentre position is indicated by black arrow on the box. The forks of the lift truck or the transpallet should be placed so that the black arrow indicated on the packing is about in the centre of the forks. The package should be handled with extreme cauti ...

1. Main Key Switch; 2. General Lamp; 3. Vacuum Motor Switch; 4. Brushes Motor Switch; 4 3 2 1 ...

CHOOSING THE DETERGENT SOLUTION For a good cleaning of the floor, it is important to choose the proper detergent solution. If necessary, ask the supplier or a competent person for the proper solution. Keep in mind that a too strong chemical agent can compromise the long life of each machine. It is necessary to use a low- sudsing detergent solution, or an antifoaming additive, in order not to damage the vacuum motor. If it is impossible ...

The main characteristic of this type of squeegee is to pick-up the water from the floor and convey to the vacuum hose, but it must be parallel to the floor. To rightly adjust the squeegee operate as follow: • Extract the key from the control dashboard to avoid accidental start of the machine. • To adjust the squeegee slope operate the knob (fig 3). ...

GENERAL SAFETY RULES Before using the machine ,instruct all operators to read carefully the charter ”SAFETY STANDARDS “WARNING. • The manufacturer can make any changes to the machine, for constructive or commercial reasons, without being obliged to change the instruction manual at the right time according to these modifications. • The person responsible for the machine must adhere to CEE rules and to the local ...

the machine when the control panel indicates defective tools, warning lights, etc. MAKE SURE THAT: - No strangers are present near the machine - No strange objects (appliances, cloths, etc.) are on the machine - The machine does not emit strange noises after its starting; if so, stop it immediately and detect the cause. All doors and protections are regular ...

The operations on the electric installation can be performed only by QUALIFIED ELECTRICIANS, instructed in the electric characteristics of the machine and in accident prevention rules. CHECKS The machine must be inspected by a technician, who checks the safety conditions of the machine and any possible damages or defects visible from outside: - before setting the machine at work - after appropriate time intervals ...

The squeegee blades should be replaced when the contact edge becomes worn; the perfection of the edge is essential for a perfect drying. To replace the blades • The squeegee should be demounted from the machine and placed on the desk. • Now, remove the screws (fig) both on the front part and on the rear part of the squeegee, the steel straps and remove worn rubber blades • Perform the inverse procedure and assemble th ...

The vacuum motors must be checked and cleaned. The brushes should be checked all six months and replaced, if necessary. After removing the key from the dashboard, unscrew the screw in the vacuum motor space, open it, unhook the hooks and detach the plug . In this way, it is possible to extract the motors and release the sponge filter under the motors that can be extracted, cleaned and replaced. Check the suction fan from the hol ...

The scrubber must be inspects from a technician that controls its safety conditions and the presence of possible damages or visible defects to the outside. • To the first operation • After changes and reparations Check to the safety devices Every 2 years to check the efficiency of the safety devices, the inspection must be performs at a professional technician. To guarantee the general ...

“THE BEST IN FLOOR MACHINES” FILIALI: 20132 MILANO – Fax. 02/2592779 Via Palmanova 211/a – Tel. 02/27207783 - 2564810 00155 ROMA – Fax. 06/22754075 Via Carlo Carrà 13 – Tel. 06/22754040-2275060 STABILIMENTO: 50030 PIANCALDOLI (FI) – Fax. 055/817144 Loc. Rombola – Tel. 055/8173610 Distributed by: ...