First Alert SFA3800 Operation & User’s Manual

AND REMOTE PENDANT USER MANUAL SFA3800 PLEASE READ THIS USER MANUAL COMPLETELY BEFORE OPERATING THIS UNIT AND RETAIN IT FOR FUTURE REFERENCE SUBSCRIPTION TO CALLER ID SERVICE FROM YOUR LOCAL TELEPHONE COMPANY IS REQUIRED FOR ALL CALLER ID FEATURES TO OPERATE CORRECTLY ...

THIS SYMBOL IS TO ALERT YOU THE IMPORTANT OPERATING OR SERVICING INSTRUCTIONS THAT MAY APPEAR IN YOUR USER MANUAL. ALWAYS FOLLOW BASIC SAFETY PRECAUTIONS WHEN USING THIS PRODUCT TO REDUCE THE RISK OF INJURY, FIRE OR ELECTRIC SHOCK. When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read and und ...

locations. 17. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. 18. Use caution when installing or modifying telephone lines. For optimal performance it is recommended that this product is used on a conventional phone line. Performance may vary with VOIP or other digital servic ...

The telephone company may make changes in its communications facilities, equipment, operations or procedures, where such action is reasonably required and proper in its business. Should any such changes render the customer’s terminal equipment incompatible with the telephone company facilities, the customer shall be given adequate notice to make modifications to maintain uninterrupted service. Gene ...

SFA3800 Telephone Set x 1 set Coiled Handset Cord (9 feet) x 1 pc Long Line Cord (7 feet) x 1 pc Short Line Cord (7 inches) x 1 pc Emergency Remote Pendant with Detachable Neck Strap (with 12V battery installed) x 1 set AC Adaptor (DC9V 200mA output) x 1 set Wall Mount Bracket x 1 set Wall Mounting Screws x 2 pcs Plastic Anchors for Wall Mounting x 2 pcs User Manual with Accessory Order Form x 1 set PROTECT YOUR FURNITURE!! T ...

THE MAIN UNIT 1. Hook Switch 14. Ringer Indicator 27. New Call Indicator 2. Handset Holder 15. Speakerphone Button 28. Keyhole for Wall Mounting 3. Delete Button 16. Speakerphone Indicator 29. Battery Compartment Cover 4. Dial Button 17. Speakerphone Microphone 30. Wall Mount Bracket Slots 5. M1 Button (One-Touch Memory Location 1) 18. Redial/Pause Button 31. Wall Mount Bracket Latch 6. M2 Button (One-Touch Memory Location 2) 19. ...

INSTALLATION POWERING UP THE TELEPHONE Insert the plug of the AC120V~ DC9V 200mA AC Adaptor (included) into the DC JACK at the back of the telephone and plug the AC Adaptor into a properly installed AC 120V~ 60Hz mains socket near the equipment and it should be easily accessible. CONNECTING THE TELEPHONE 1. Plug one end of the telephone line cord into the TEL.LINE JACK at the bottom of the telephone base. 2. Plug the other ...

REMOTE PENDANT TOP COVER. 3. Remove the old battery and load a new 12V type LR23 alkaline battery into the battery compartment following the polarity markings as indicated on the PCB. (Remarks: the metal plate with a spring is the negative battery terminal). 4. Snap the REMOTE PENDANT TOP COVER back into place and tighten the screw on the ...

5 Name Recording Record a name for a telephone number in the phone book 6 Record Message Record a new emergency message 7 Check Message Listen to the recorded emergency message 8 Flash Set the flash time. Options are: 600, 300 (default), 270, 100 and 80ms 9 Tone/Pulse Set the dialing mode between tone or pulse. 0 Remote Pendant For pairing the remote pendant with your telephone (up to 5 remote p ...

4. Press BUTTON to exit the setup mode. SETTING THE TONE/PULSE DIALING MODE 1. Press MENU BUTTON repeatedly (or press MENU then  buttons) until “TONE/PULSE” is shown. 2. Press the DIAL BUTTON. 3. Select the required dialing mode using the  or  and confirm with the DIAL BUTTON. 4. Press BUTTON to exit the setup mode. SETTING THE RINGER VOLUME CONTROL The ringer sound level can be adjusted by sliding the RINGER SE ...

BUTTON and replace the HANDSET to the HANDSET CRADLE accordingly. PRE-DIALING A PHONE NUMBER 1. Enter the telephone number on the KEYPAD. The telephone will voice the digits dialed (with Voice Prompt ON and set to either English, Spanish, Italian or French). 2. To modify a number, press the DELETE BUTTON for each digit to be corre ...

RECORDING YOUR EMERGENCY MESSAGE 1. Press MENU BUTTON repeatedly (or press MENU then  buttons) until “RECORD MESSAGE” is shown. 2. Press and hold the DIAL BUTTON until you hear a beep and “VOICE” icon flashes in the LCD Display; then speak into the SPEAKERPHONE MIC simultaneously. The maximum recording time of the Emergency Message is 20 seconds. 3. Release the DIAL BUTTON when you have finished recording. The ph ...

Note : The phone book features are only available in phone book mode ( icon turns ON). If the icon is off, press button once to turn it ON. STORING NUMBERS, NAMES AND VOICE PROMPTS IN THE PHONE BOOK (UP TO 30 ENTRIES) 1. Press MENU BUTTON repeatedly (or press MENU then  buttons) until “STORE NUMBER” is shown. 2. Press the DIAL BUTTON. The cursor will flash in the first position. 3. Enter the required telephone number with a ma ...

Notes:  If no telephone number is stored, the display will show “EMPTY”.  After you view all the enteries in memory, the display will show “END OF LIST”. TO DIAL THE DISPLAYED TELEPHONE NUMBER FROM THE PHONE BOOK MEMORY 1. With the selected telephone number showing on the LCD DISPLAY, press DIAL BUTTON. The displayed telephone number will be dialed out automaticall ...

DELETE BUTTON for 2 seconds until “EMPTY” appears on the display. ONE-TOUCH MEMORIES STORING NUMBERS IN THE ONE-TOUCH MEMORIES This telephone has two One-Touch memories: M1 and M2. Once a number has been stored in each of these memory locations, you only need a single press to make the call. 1. Press and release the MENU BUTTON until “STORE NU ...

1. Press  to review more recent calls. The CALL# will decrease. After you view the most recent data in memory, the display will show “END OF LIST”. 2. Press  to review older calls. The CALL# will increase. After you view the oldest data in memory, the display will show “END OF LIST”. 3. If the data in memory is being reviewed for the first time, the “NEW” icon will light. The NEW CALL INDICATOR will go OFF a ...

 Check to see if the VOLUME BOOST INDICATOR is “ON”. The red LED on the left side of the +40dB VOLUME BOOST BUTTON should light.  Check the AC Adaptor and make sure it is properly plugged into the ac power outlet and into the DC JACK on the phone. Noise, Static, Interferences while using the handset  A filter may be required for homes with DSL line or near Radio towers. There is a red light that continues to flash ...

1. Clean your phone with a damp (never wet) cloth. Solvent or detergent should never be used. 2. If your phone stops working, check to be certain that all modular plugs are properly “snapped” into their jacks. 3. If the phone still doesn’t work and you have other telephones installed in your home, check to see if they are working. If they are, try using your telephone on another outlet. If it still doesn’t work, it is more ...

1. The warranty applies to the SPECTRA product only while: a) It remains in the possession of the original purchaser and proof of purchase is demonstrated b) It has not been subjected to accident, misuse, abuse, improper service, usage outside the descriptions and warnings covered within the owner’s manual or non-SPECTRA approved modifications c) Claims are made within th ...