DELTA DORE TYBOX 610 Installation Manual

directives 2004/108/EC (Electromagnetic Compatibility) and 2006/95/EC (Low-Voltage Safety) Because of changes in standards and equipment, the characteristics given in the text and the illustrations provided in this document are not binding unless expressly confirmed *2702305_Rev.1* PROG AUTO TYBOX 0h 2 4 6 8 10 12 14 16 18 20 22 24 1234567 i PROG AUTOO 0h 2 4 6 8 10 12 14 16 18 20 22 24 TYBOX 610 Weekly ...

Warnings Contents • Carefully read these instructions prior to installation. • The unit must be installed in compliance with current standards. • Always switch off the mains before installing or servicing the unit. • Do not attempt to repair the unit yourself; an after-sales service is available. • Check that the fastenings are suited to the surface to which the unit will be attached (plasterboard, brick, etc.). • The diagrams provided ha ...

- 4 - Fitting the thermostat We recommend that you install your device: - where there is easy access, such as a corridor, living room or entrance hall, - on an interior wall at a height of 1.50m from the floor Your appliance will also show you the room temperature. It is therefore recommended that it be installed well removed from any sources of heat (e.g. convec- tors, chimney) and draughts (e.g. doors, windows). 1 2 • Remove the protective tab fr ...

Connections • Connect receiver terminals 1 and 3 to both termi- nals of the boiler thermostat input. • If necessary, remove the shunt connecting the two thermostat input terminals. • If the boiler has a clock input, do not mistake it for the thermostat input. Connecting a boiler with thermostat input 1 2 3 - 7 - • Connect the control wires (see the section on Connections) and screw back in the locking screw for the protective cover Fitting th ...

1 2 3 1 2 3 1 2 3 Controlling a heat pump Select cabling that is suitable for your heat pump or refer directly to the manufacturer's specifications. N N L L 1 2 3 Controlling electric convectors To control electrical convectors, you MUST use a power contact switch that is suitable for the total power to be controlled. This power contactor switch must be fitted into the electrical switchboard of your home. - 8 - Connecting a boiler without thermostat ...

Configuration To access the configuration menus, turn the knob to the position marked Press OK to access menu CF01 The reference number of your device is displayed as well as the version number - 10 - Activation Turn the knob to the position The day numbers flash. • Press + or - to set the day, then OK to confirm and go to the next setting. Repeat these steps to set the hours and minutes. To exit the “time setting” mode, turn the selector knob ...

Enter your desired setting using the + or - buttons. Press OK to confirm and move on to menu CF03 Setting the comfort temperature in heating mode Enter your desired setting using the + or - buttons. Press OK to confirm and move on to menu CF04 - 12 - Correcting the temperature measured IMPORTANT: In order to change this setting, the unit has to have been running for at least 2 hours beforehand. If there is a ...

If your thermostat controls a circulator, set the value of the CF05 menu to equal 1. Circulator anti-seizing Control time base Select the time base recommended for your type of installation Enter your desired setting using the + or - buttons Press OK to confirm Enter your desired setting using the + or - buttons Press OK to confirm and move on to menu CF06 - 14 - With thermostatic valve electric heating or hot water heaters, the Comfort temperature ...

Summary table of configurations CF01 Correction of the temperature measured by -4°C to +4°C in increments of 0.1°C (0 by default). CF02 Automatic mode temperature display option 0 = Continuous set-point temperature display (by default) 1 = Room temperature display CF03 Control of the Comfort temperature in heating mode 0 = controlled by the Tybox (by default) 1 = by each radiator or convector CF04 Air conditioning function 0 = Not authorised ...

Technical features • Power supplied by two LR03 or AAA 1.5 V alkaline batteries. “No rechargeable batteries” • 1 2A / 230V power outlet • Dimensions: 111 x 84 x 28.5 mm • Protection rating: IP 30 • Installation in an environment with normal pollution levels • Storage temperature: -10°C to +70°C • Operating temperature: 0°C to +40°C • Type 1C brownout • Class II insulation • Clock save: 30 seconds Notes ...