Directed AS-RFK2800 Operation & User’s Manual

INDUSTRY CANADA USER NOTICE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. Doc#: 120914 Rev:1.7 © 2012 - AS-RFK2800 - - CP - Canada AS-RFK2800 User Guide Designed & engineered in Canada Available functionalities depend on vehicle. Consult your dealer for more information.

dealer for available options. Table of Contents Government Regulations ........................................................................................................ 3 Charging the Remote Control ................................................................................................ 4 LCD 2-Way ................................................................................................................................ 4 Fault Condition Alerts .......................................................................................................... 5 Status Screen Icons ................................................................................................................ 5 Basic Commands..................................................................................................................... 6 Remote Start ........................................................................................................................ 6 Lock ..................................................................................................................................... 6 Unlock .................................................................................................................................. 6 AUX/Trunk ........................................................................................................................... 6 Advanced Commands ............................................................................................................. 6 Runtime Reset ..................................................................................................................... 6 LCD Remote Configuration .................................................................................................... 7 Navigating Menus and Options............................................................................................ 7 Access Menu Items ............................................................................................................. 7 Remote Pairing .................................................................................................................... 7 Remote Features (Main Menu) ............................................................................................ 7 Setup Remote menu ............................................................................................................ 7 Pair Remote ......................................................................................................................... 9 Demo Mode ......................................................................................................................... 9 Power Off ............................................................................................................................. 9 Exit ....................................................................................................................................... 9 Remote Start Features .......................................................................................................... 10 Disabling Remote Start ...................................................................................................... 10 Remote and System Operations .......................................................................................... 10 Out of Range ..................................................................................................................... 10 No Remote Output ............................................................................................................. 10 1-Way Companion Remote Control ..................................................................................... 11 Using the 1-Way Companion Remote ............................................................................... 11 Accessing Commands ....................................................................................................... 11 Lock Keypad ...................................................................................................................... 11 Programming ..................................................................................................................... 11 Battery Information (1-Way) ............................................................................................... 12 Battery Information (LCD) ..................................................................................................... 12 Low Battery ........................................................................................................................ 12 Low Battery Alerts .............................................................................................................. 12 Battery Life ......................................................................................................................... 13 Battery Disposal ................................................................................................................. 13

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with the Industry Canada Radio Standards Specification RSS 210. Its use is authorized only on a no-interference, no-protection basis; in other words, this device must not be used if it is determined that it causes harmful interferences to services authorized by IC. In addition, the user of this device must accept any radio interface that may be received, even if this interference could affect the operation of the device. Warning! Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.

Your Autostart LCD remote is powered by an internal rechargeable battery that can only be serviced by an authorized Directed dealer. Due to transit and storage time prior to your purchase, the battery charge may have depleted. To ensure proper operation, check the battery level and connect the battery charger if not fully charged. See the “Battery Information (LCD)” and “Status Screen Icons” sections for more information about the battery. Charging the remote control: 1. Plug the AC adapter into a 110V AC outlet. Insert the mini-USB connector into the mini- USB port located on the side of the remote control (see diagram under LCD 2-way). The text field will display CHARGE to indicate the remote control is charging (The remote remains operational while charging and can command the system). 2. Once fully charged the text field will display FULL. 3. The remote control is then ready for use. Disconnect the mini-USB end from the remote control first and then the AC adapter from the AC outlet. Note: If the battery is excessively depleted when the charger is connected, functionality may be delayed while it charges to the minimum voltage required to operate the display, after which normal charging resumes. LCD 2-Way Your remote system is equipped with a 5-button multi-channel remote control. The functions of the transmitter are as follows: DISPLAY: Status Screen: The upper portion of the display contains status icons for the System, Remote Start and Remote Control. Text field: The lower portion of display – shows the Clock, or Runtime, as well as Command confirmations, Page messages and programming menus. LOCK: Locks the doors. TRUNK: Opens the TRUNK. UNLOCK: Unlocks the doors. START/STOP: Remote starts or stops the engine. MINI-USB PORT: The battery charger plugs into this port.  SHIFT: Allows access to programming and modifies operation of the other buttons. N.B.: Pressing  then the LOCK button will activate the AUX 1 output. Pressing  then the UNLOCK button will activate the AUX 2 output.

If, when performing a command, a condition exists that does not allow activation of a Remote Start feature*, the NOT AVAILABLE or REMOTE START ERROR text and a fault tone will play. * Remote Start feature not available when the Remote Start status is incorrect upon receiving the command. Refer to the notes included in the command descriptions that address these faults. Status Screen Icons The table below describes all the status screen icons. Icon Description System Status Locked: The system is Locked. Unlocked: The system is Unlocked. Remote Start Remote start is active, the engine is running. On during Aux/Trunk channel activation. On during Fault Report to indicate the Hood is open. Remote Control Status Bars indicate battery level is Full, ¾,½,¼ or Empty. On while the remote control is transmitting a command. On while the remote control is receiving a message. On with Out of Range fault tone to indicate the remote failed to receive a command confirmation. Pager on: The remote will wake up to listen for messages. Pager off: The remote will not wake up to listen for messages. The remote will Vibrate when messages are received. The remote will emit Beeps and Tones when messages are received. Text Field Text field Displays the Clock, Runtime, message text and feature menus.