Contura 550 Installation Instructions Manual

Type designation Contura 550 Manufacturing number See rating plate on the stove Intended area of use Heating of rooms in residential buildings Fuel Wood MANUFACTURER Name NIBE AB / Contura Address Box 134, Skulptörvägen 10 SE-285 23 Markaryd, Sweden CHECKS According to AVCP System 3 European standard EN 13240:2001 / A2:2004 Test institute Rein-Ruhr Feuerstätten Prüfstelle, NB 1625, has checked declared performance and issued test report no. RRF-40 09 2088 PERFORMANCE DECLARATION No. C550-CPR-130601-SE-1 DECLARED PERFORMANCE Essential characteristics Performance Harmonised technica ...

Technical details 68 Removing the loose parts 68 Connection to chimney 70 Supply of combustion air 71 Installation distances 72 Assembly 73 Installing base 76 Installing drawer 77 A warm welcome to Contura A warm welcome to the Contura family. We hope you will get a great deal of pleasure from your new stove. As a new owner of a Contura stove, you have secured a product with timeless design and long service life. Contura also has a combustion process that is both environmentally friendly and efficient, for the best heat production. Read through these installation instructions carefully before installation. Read how to best light ...

Model 550 Height (mm) 1010 Width (mm) 500 Depth (mm) 440 Weight (kg) 100 Type approved in accordance with: European standard EN-13240 Swedish environmental and quality marking, P-marking cert. no. 220309 Norwegian standard NS 3059, SINTEF 043-140 German standard DIN, 18.891, RO-91 03 529 Danish standard DS/EN 13240 Plus, id no. 598 Removing the loose parts If the insert needs to be put down to be moved, loose components should be removed. When the stove is installed reinstall the components in reverse order. 1 Fire bars 2 Grate disc 3 Heat deflector 4 Hearth cladding (Vermiculite). 1 ...

Handle the vermiculite with care. Lift the smoke baffle with one hand whilst removing the sides pieces. Reinstall in reverse order 4 How to remove the heat deflector 3 2 1 ...

Ø ca 180 mm LEK ! 4 6 5 1 3 2 70 GB CHIMNEY Connection to chimney Rear connection to a masonry chimney Top connection to the chimney Make sure that the connector gasket does not work loose when the connection pipe is placed on the connector. If further sealing material is required, heat- resistant sealant may be used. The back panel must be installed before the stove is rear connected. The hot air grille must be installed before chimney top connection. • The stove meets the requirements for connecting to chimneys dimensioned for 350°C flue gas temperature. • The external diameter of the connection sleeve is 150 mm. � ...

When a stove is installed in a room, the demand for air supply to the room increases. Air can be provided indirectly via a vent in the outer wall or via a duct from the outside that is connected to the connector on the underneath of the stove. The amount of air needed for combustion is approx. 25m3/h. The connector has an external diameter of 67 mm. When duct routing further than 1 m the pipe diameter must be increased to 100 mm and a correspondingly larger wall vent must be selected. In hot areas the duct should be insulated with 30 mm mineral wool covere ...

separate glass hearth plates (accessory). ** To prevent discolouration of painted non-flammable walls we recommend that the same side distance as to combustible walls is used. The minimum distance in front of the stove opening to combustible parts of the building or interior decoration must be at least 1 m. When top connecting a steel flue, please refer to the particular manufacturer's installation instructions. Observe the safety distan ...

ASSEMBLY 1 3 2 To facilitate the installation of the side panels, the two upper screws for the back panel must not be tightened before the side panels are installed. Installing rating plate Supplied rating plate positioned on underneath of heat deflector, or with fan option on the inside of the stove. ...

and turn the side panel’s front edge around the edge of the base frame. Hook the side panel on the back panel. Align and depress the side panel end over the base panel’s shaft pin. Clean the glass thoroughly before installing the side panels! ...

the stove is used. Also read the ”Lighting instructions”, before lighting for the first time. Final inspection of the installation 5 6 ASSEMBLY ...

knockout in the back panel must always be removed for the supply of convection air. 1 3 2 4 ASSEMBLY Installing base ...

the knockout in the back panel must always be removed for the supply of convection air. 1 3 2 ASSEMBLY Installing drawer ...

2014-01-28 Contura reserves the right to change dimensions and procedures described in these instructions at any time without special notice. The current edition can be downloaded from www.contura.eu NIBE AB · Box 134 · 285 23 Markaryd · Sweden www.contura.eu ...