D-Link DCS-4701E Operation & User’s Manual

D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Information in this document may become obsolete as our services and websites develop and change. Manual Revisions Revision Date Description 1.0 April 21, 2015 DCS-4701E Revision A1 with firmware version 1.00 Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies. Copyright © 2015 D-Link Corporation. All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Corporation. Preface

Table of Contents Product Overview..........................................................................4 Package Contents..................................................................4 Introduction.............................................................................5 System Requirements..........................................................5 Features.....................................................................................6 Hardware Overview..............................................................7 Front and Back....................................................................7 Sides.......................................................................................8 Mounting the Camera..........................................................9 Waterproofing Your Installation.................................11 Software Installation.......................................................14 Configuration................................................................................17 Using the Configuration Interface.................................17 Live Video...............................................................................19 Setup........................................................................................21 Setup Wizard.....................................................................21 Network Setup..................................................................26 Dynamic DNS....................................................................29 Image Setup......................................................................30 Video....................................................................................32 Preset....................................................................................34 Motion Detection............................................................36 Time and Date...................................................................37 Event Setup........................................................................38 Advanced................................................................................45 ICR and IR............................................................................45 HTTPS...................................................................................46 Access List...........................................................................47 SNMP....................................................................................48 Maintenance..........................................................................50 Device Management......................................................50 System.................................................................................51 Firmware Upgrade...........................................................52 Status.......................................................................................53 Device Info.........................................................................53 Logs......................................................................................54 Help......................................................................................55 Technical Specifications............................................................56

Section 1: Product Overview Product Overview Package Contents If any of the above items are missing, please contact your reseller. Safety Notice: Installation and servicing should be done by certified technicians so as to conform to all local codes and prevent voiding your warranty. DCS-4701E Vigilance HD Outdoor PoE Mini Bullet Camera Rubber Power Connector Plug Mounting Kit CD-ROM with User Manual and software Quick Installation Guide Cable Waterproofing Connector

Section 1: Product Overview Introduction Congratulations on your purchase of the DCS-4701E Vigilance HD Outdoor PoE Mini Bullet Camera. The DCS-4701E is a professional surveillance and security solution for small, medium, and large enterprises alike. The DCS-4701E uses an HD progressive scan CMOS sensor; the professional sensor results in low noise and high sensitivity capabilities ideal for surveillance applications. The DCS-4701E is a complete system with a built-in CPU and incorporates a web server, allowing it to transmit excellent real- time Full HD resolution video for security and outdoor surveillance. The DCS-4701E can be accessed remotely, controlled and configured from any PC/Notebook over your local network or through the Internet via a web browser. The simple installation and intuitive web-based interface offer easy configuration across the full range of its advanced feature set, including granular control over multiple video streams with different configurations and multicast video streams which helps you manage your network load. The DCS-4701E has an IP66 certified weatherproof housing designed for both indoor and outdoor applications. The built-in removable IR-cut filter and IR LEDs give the DCS-4701E the capability to view up to 30M at night. The DCS-4701E also incorporates Power over Ethernet (PoE), allowing it to be easily installed in a variety of locations without the need for supplemental power cabling. The combination of IP66 weatherproof housing, IR-Cut Filter, IR LEDs, and PoE make the DCS-4701E an ideal solution for a dependable and cost-effective 24 hour surveillance solution with easy clutter-free installation. • Computer with Microsoft Windows® 8, 7, or Vista® (for CD-ROM Setup Wizard), Mac OS or Linux • Internet Explorer 7, Firefox 20, Chrome 20, or Safari 6 or higher • Existing 10/100 Ethernet-based network with an available 802.3af Power over Ethernet (PoE) port System Requirements

Section 1: Product Overview Simple to Maintain The DCS-4701E is a stand-alone system with a built-in CPU, requiring no special hardware or software. The DCS-4701E can be viewed and managed through most web browsers, including Internet Explorer®, Chrome®, Firefox®, and Safari®. Supports a Variety of Platforms With support for TCP/IP networking, HTTP, and other Internet related protocols, the DCS-4701E can also be integrated easily into other Internet/ Intranet applications because of its standards-based features. The DCS-4701E works with any 10/100 Ethernet network, making the DCS-4701E easy to integrate into your existing network environment. Advanced Event Management The DCS-4701E can be set up to send e-mail notifications with snapshots when an event occurs, such as when motion is detected. Events can be triggered from several sources, such as motion detection and time based events. IR LEDs for Day and Night Functionality The built-in infrared LEDs enable night time viewing of up to 30 meters. IP66 Weatherproof Housing The DCS-4701E uses an IP66 weatherproof housing, allowing you to rest assured that in the toughest of conditions, it will continue to provide round-the-clock surveillance. PoE (Power over Ethernet) for Flexible Installation The DCS-4701E can draw all the power it needs from a PoE switch or PoE injector for a simple and clutter-free installation. Remote Monitoring Utility The D-ViewCam application adds enhanced features and functionality for the Network Camera and allows administrators to configure and access the Network Camera from a remote site via Intranet or Internet. Other features include image monitoring, recording images to a hard drive, viewing up to 32 cameras on one screen, and taking snapshots. Features

Section 1: Product Overview Front and Back Hardware Overview 1 Camera Lens Fixed lens to record video of the surrounding area 2 IR LEDs Infrared LEDs illuminate the camera's field of view at night 3 Grounding Screw Can be attached to a grounding wire if desired 4 Reset Button Press and hold for 10 seconds to reset camera back to the factory default settings 5 Adjustment Ring Loosen to adjust camera angle and tighten to lock camera angle 5 3 4 1 2

Section 1: Product Overview Sides 1 Ethernet Jack RJ-45 connector for Ethernet, can also be used to power the camera using Power over Ethernet (PoE) 2 Power Connector Connects to an optional 12 V / 1.5 A power adapter (not included) 1 2

Section 2: Assembly and Installation Mounting the Camera It is highly recommended that you configure and test your camera before mounting it. Step 1 Place the mounting sticker where you want to position the camera. Make sure the camera base will be positioned so that the cable channel is on the bottom. Use a 6 mm drill bit to make the required holes approximately 25 mm deep, then insert the wall anchors into the holes. If you are running the camera cables through the wall, drill a hole in the center and pull the cables through the hole. Step 2 Use the screws provided to mount the camera to the wall. If you are running the camera cables out the side of the camera, guide the camera cables through the cable channel on the base.

Section 2: Assembly and Installation Step 3 Connect the power and Ethernet cables, or just the Ethernet cable if you are using a PoE connection. Step 4 To adjust the camera's angle, turn the adjustment ring counterclockwise to loosen it, then move the camera to the desired position and angle. When you are finished, turn the adjustment ring clockwise to tighten it. If you need to waterproof your installation, please continue to the next page.

Section 2: Assembly and Installation Waterproofing Your Installation Step 1 Place the washer around the base of the Ethernet connector as shown. To waterproof your camera installation, follow the instructions below. Round Ethernet cable, a crimping tool, and RJ-45 plugs are required for this procedure. Step 2 Thread bare Ethernet cable through the waterproof connector as shown, then crimp an RJ-45 plug onto the cable.

Section 2: Assembly and Installation Step 4 Screw the back part of the waterproof connector clockwise until there is a tight seal around the Ethernet cable. Step 3 Connect the RJ-45 plug into the Ethernet connector, then screw the waterproof connector to the Ethernet connector by turning it about a half-turn clockwise. If you are using PoE to power your camera, use the included rubber power connector plug to the power connector.

Section 2: Assembly and Installation If you are using a power adapter(not included) to power your camera, wind waterproof tape around the connection in an overlapping manner to cover it.

Section 2: Assembly and Installation Step 1 Insert the DCS-4701E CD into your computer's CD-ROM drive to begin the installation. If the Autorun function on your computer is disabled, or if the D-Link Launcher fails to start automatically, click the Start button and type D:\autorun.exe (where D: represents the drive letter of your CD-ROM drive) and press Enter. Step 2 Click on the D-Link Setup Wizard SE icon that was created in your Windows Start menu (Start > D-Link > Setup Wizard SE). Software Installation

Section 2: Assembly and Installation Step 4 Enter the Admin ID and password. When logging in for the first time, the default Admin ID is admin with the password left blank. Click the checkboxes if you wish to change the admin ID and password for the camera, and enter the new ID and password you wish to use. Click Next to continue. Step 3 The Setup Wizard will appear and display the MAC address and IP address of your camera(s). If you have a DHCP server on your network, a valid IP Address will be displayed. If your network does not use a DHCP server, the network camera's default static IP 192.168.0.20 will be displayed. Select your camera, then click the Wizard button to continue.

Section 2: Assembly and Installation Step 6 Take a moment to confirm your settings and click Restart. Step 5 Select DHCP if your camera obtains an IP address automatically from a DHCP server such as a router. Select Static IP if you want to manually enter the IP settings for the camera. Click Next to continue.

Section 3: Configuration Configuration Using the Configuration Interface After completing the Camera Installation Wizard, you are ready to use your camera. The camera’s built-in Web configuration utility is designed to allow you to easily access and configure your DCS-4701E. At the end of the wizard, click Link, or enter the IP address of your camera into a web browser, such as Mozilla Firefox. To log in, use the User name admin and the password you created in the Installation Wizard. If you did not create a password, the default password is blank. After entering your password, click OK. Step 1 Click on the D-Link Setup Wizard SE icon that was created in your Windows Start menu (Start > D-Link > Setup Wizard SE). Step 2 Select the camera and click Link to access the web configuration. The Setup Wizard will automatically open your web browser to the IP address of the camera.

Section 3: Configuration Step 3 Enter admin as the default username and leave the password blank. Click OK to continue. Step 4 This section displays your camera’s live video. You can select your video profile and view or operate the camera.

Section 3: Configuration Live Video This section shows your camera’s live video. You may select any of the available icons listed below to operate the camera. You may also select your language using the drop-down menu on the left side of the screen. You can zoom in and out on the live video image using your mouse. Right-click to zoom out or left-click to zoom in on the image. Motion Trigger Indicator This indicator will change color when a trigger event occurs. Note: The video motion feature for your camera must be enabled. Recording Indicator When a recording is in progress, this indicator will change color. Control Pad This control pad can be used to electronically pan, tilt, and zoom (ePTZ) within the camera's predefined view area, if one has been defined. Auto Pan Starts the automatic panning function. The ROI will pan from back and forth within the FOV. Stop Stops the camera ePTZ motion. Preset Path Starts the camera's motion along the predefined path.

Section 3: Configuration If any presets have been defined, you can select them here to move the camera to the selected preset. Go To: (Preset List) Video Profile 1 Video Profile 2 Video Profile 3 Full screen mode Take a Snapshot Record a Video Clip Set a Storage Folder You may select a value between 0 and 10. 0 is the slowest and 10 is the fastest. This window indicates the total field of view (FOV) of the camera. The red box indicates the visible region of interest (ROI). You may select the interface language using this menu. ePTZ Speed: Global View: Language:

Section 3: Configuration Setup Setup Wizard To configure your Network Camera, click Internet Connection Setup Wizard. Alternatively, you may click Manual Internet Connection Setup to manually configure your Network Camera and skip to "Network Setup" on page 26. To quickly configure your Network Camera’s motion detection settings, click Motion Detection Setup Wizard. If you want to enter your settings without running the wizard, click Manual Motion Detection Setup and skip to"Motion Detection" on page 36.

Section 3: Configuration Internet Connection Setup Wizard This wizard will guide you through a step-by-step process to configure your new D-Link Camera and connect the camera to the internet. Click Next to continue. Select how the camera will connect to the Internet. If your camera is connected to a router, or you are unsure how your camera will connect to the Internet, select DHCP Connection. Select Static IP if your Internet Service Provider has provided you with connection settings, or if you wish to set a static address within your home network. Enter the correct configuration information and click Next to continue. If you are using PPPoE, select Enable PPPoE and enter your user name and password. Click Next to continue.

Section 3: Configuration If you have a Dynamic DNS account and would like the camera to update your IP address automatically, Select Enable DDNS and enter your host information. Click Next to continue. Enter a name for your camera and click Next to continue. Configure the correct time to ensure that all events will be triggered as scheduled. Click Next to continue. If you have selected DHCP, you will see a summary of your settings, including the camera's IP address. Please write down all of this information as you will need it in order to access your camera. Click Apply to save your settings.

Section 3: Configuration This wizard will guide you through a step-by-step process to configure your camera's motion detection functions. Click Next to continue. Motion Detection Setup Wizard Step 1 This step will allow you to enable or disable motion detection, specify the detection sensitivity, and adjust the camera’s ability to detect movement. You may specify whether the camera should capture a snapshot or a video clip when motion is detected. Refer to "Motion Detection" on page 36 for information about how to configure motion detection. Step 2 This step allows you to enable motion detection based on a customized schedule. Specify the day and hours. You may also choose to always record whenever motion is detected.

Section 3: Configuration Step 3 This step allows you to specify how you will receive event notifications from your camera. You may choose not to receive notifications, or to receive notifications via e-mail or FTP. Please enter the relevant information for your e-mail or FTP account. Click Next to continue. Step 4 You have completed the Motion Detection Wizard. Please verify your settings and click Apply to save them. Please wait a few moments while the camera saves your settings and restarts.

Section 3: Configuration Network Setup Use this section to configure the network connections for your camera. All relevant information must be entered accurately. After making any changes, click the Save Settings button to save your changes. LAN Settings: DHCP: Static IP Client: IP Address: Subnet Mask: Default Gateway: Primary DNS: Secondary DNS: This section lets you configure settings for your local area network. Select this connection if you have a DHCP server running on your network and would like your camera to obtain an IP address automatically. If you choose DHCP, you do not need to fill out the IP address settings. You may obtain a static or fixed IP address and other network information from your network administrator for your camera. A static IP address may simplify access to your camera in the future. Enter the fixed IP address in this field. This number is used to determine if the destination is in the same subnet. The default value is 255.255.255.0. The gateway used to forward frames to destinations in a different subnet. Invalid gateway settings may cause the failure of transmissions to a different subnet. The primary domain name server translates names to IP addresses. The secondary DNS acts as a backup to the primary DNS.

Section 3: Configuration Enable UPnP Presentation: Enable UPnP Port Forwarding: Enable PPPoE: User Name / Password: HTTP Port: Access Name for Stream 1~3: HTTPS Port: Authentication: RTSP Port: Enable CoS: Enabling this setting allows your camera to be configured as a UPnP device on your network. Enabling this setting allows the camera to add port forwarding entries into the router automatically on a UPnP capable network. Enable this setting if your network uses PPPoE. Enter the username and password for your PPPoE account. Re-enter your password in the Confirm Password field. You may obtain this information from your ISP. The default port number is 80. The default name is video#.mjpg, where # is the number of the stream. You may use a PC with a secure browser to connect to the HTTPS port of the camera. The default port number is 443. Choose to enable or disable RTSP digest encryption. Digest encryption uses MD5 hashes. The port number that you use for RTSP streaming to mobile devices, such as mobile phones or PDAs. The default port number is 554. You may specify the address of a particular stream. For instance, live1.sdp can be accessed at rtsp://x.x.x.x/video1.sdp where the x.x.x.x represents the IP address of your camera. Enabling the Class of Service setting implements a best-effort policy without making any bandwidth reservations.

Section 3: Configuration Enable QoS: Enable IPv6: Enable Multicast for stream: Enable Bonjour: Bonjour Name: Enabling QoS allows you to specify a traffic priority policy to ensure a consistent Quality of Service during busy periods. If the Network Camera is connected to a router that itself implements QoS, the router's settings will override the QoS settings of the camera. Enabling this setting will enable use of the IPv6 protocol. Click the IPv6 Information button to see the camera's current IPv6 details, or you can check Manually setup the IP address to manually set up the IP address, specify a default router, and set the primary DNS. The DCS-4701E allows you to multicast each of the available streams via group address and specify the TTL value for each stream. Enter the port and TTL settings you wish to use if you do not want to use the defaults. Enable this to allow other network devices to connect to this camera using Bonjour. Enter the name to identify this camera on Bonjour.

Section 3: Configuration Dynamic DNS DDNS allows you to access your camera using a domain name instead of an IP address. To do this, you will need to have an account with one of the DDNS services listed in the drop-down box on this page. Enable DDNS: Server Address: Host Name: User Name: Password: Timeout: Status: Select this checkbox to enable the DDNS function. Select your Dynamic DNS provider from the pull down menu or enter the server address manually. Enter the host name of the DDNS server. Enter the user name or e-mail used to connect to your DDNS account. Enter the password used to connect to your DDNS server account. Enter the DNS timeout values you wish to use. Indicates the connection status, which is automatically determined by the system.

Section 3: Configuration Image Setup In this section, you may configure the video image settings for your camera. A preview of the image will be shown in Live Video. Enable Privacy Mask: Mirror: Flip: Anti Flicker: White Balance: The Privacy Mask setting allows you to specify up to 3 rectangular areas on the camera's image to be blocked/ excluded from recordings and snapshots. You may click and drag the mouse cursor over the camera image to draw a mask area. Right clicking on the camera image brings up the following menu options: ƒƒ Disable All: Disables all mask areas ƒƒ Enable All: Enables all mask areas ƒƒ Reset All: Clears all mask areas. This will mirror the image horizontally. This will flip the image vertically. When turning Flip on, you may want to consider turning Mirror on as well. Select the frequency used by your power lines to avoid interference or distortion. Use the drop-down box to change white balance settings to help balance colors for different environments. You can choose from Auto, Outdoor, Indoor, Fluorescent, and Push Hold.

Section 3: Configuration Exposure Mode: Denoise: Brightness: Contrast: Saturation: Sharpness: WDR Level: 3D Filter: Reset Default: Changes the exposure mode. Use the drop-down box to set the camera for Indoor, Outdoor, or Night environments, or to Moving to capture moving objects. The Low Noise option will focus on creating a high- quality picture without noise. You can also create 3 different custom exposure modes. The Max Gain setting will allow you to control the maximum amount of gain to apply to brighten the picture. This setting controls the amount of noise reduction that will be applied to the picture. Adjust this setting to compensate for backlit subjects. Adjust this setting to alter the color intensity/strength. This setting controls the amount of coloration, from grayscale to fully saturated. Specify a value from 0 to 8 to specify how much sharpening to apply to the image. WDR makes it easier to see objects that may appear dark due to strong backlighting conditions during the daytime. Higher WDR levels will make it easier to see objects in shadows. 3D filtering reduces the amount of image noise when viewing a low-light environment. Higher levels of 3D filtering will apply stronger levels of noise reduction. Click this button to reset the image to factory default settings.

Section 3: Configuration Video You may configure up to 3 video profiles with different settings for your camera. Hence, you may set up different profiles for your computer and mobile display. After making any changes, click the Save Settings button to save your changes. Aspect ratio: Mode: Frame size / View window area: Maximum frame rate: Video Quality: Set the aspect ratio of the video to 4:3 standard or 16:9 widescreen. Set the video codec to be used to JPEG, MPEG-4, or H.264. Frame size determines the total capture resolution, and View window area determines the Live Video viewing window size. If the Frame size is larger than the Live Video size, you can use the ePTZ controls to look around. 16:9 1280 x 720, 800 x 448, 640 x 360, 480 x 272, 320 x 176 up to 30 fps 4:3 960 x 720, 800 x 592, 640 x 480, 320 x 240 up to 30 fps Note: If your View window area is the same as your Frame size, you will not be able to use the ePTZ function. A higher frame rate provides smoother motion for videos, and requires more bandwidth. Lower frame rates will result in stuttering motion, and requires less bandwidth. This limits the maximum frame rate, which can be combined with the "Fixed quality" option to optimize

Section 3: Configuration Constant bit rate: Fixed quality: the bandwidth utilization and video quality. If fixed bandwidth utilization is desired regardless of the video quality, choose "Constant bit rate" and select the desired bandwidth. The bps will affect the bit rate of the video recorded by the camera. Higher bit rates result in higher video quality. Select the image quality level for the camera to try to maintain. High quality levels will result in increased bit rates.

Section 3: Configuration Preset This screen allows you to set preset points for the ePTZ function of the camera, which allows you to look around the camera's viewable area by using a zoomed view. Presets allow you to quickly go to and view a specific part of the area your camera is covering, and you can create preset sequences, which will automatically change the camera's view between the different presets according to a defined order and timing you can set. Note: If your View window area is the same as your Frame size, you will not be able to use the ePTZ function. Video Profile: ePTZ Speed: Arrow Buttons and Home Button: Input Preset Name: Preset List: Preset Sequence: This selects which video profile to use. You may select a value between 0 and 10. 0 is the slowest and 10 is the fastest. Use these buttons to move to a specific part of the viewing area, which you can then set as a preset. Click the Home button to return to the center of the viewing area. Enter the name of the preset you want to create, then click the Add button to make a new preset. If an existing preset has been selected from the Preset List, you can change its name by typing in a new name, then clicking the Rename button. Click this drop-down box to see a list of all the presets that have been created. You can select one, then click the GoTo button to change the displayed camera view to the preset. Clicking the Remove button will delete the currently selected preset. This section allows you to create a preset sequence, which automatically moves the camera's view between a set of preset views.

Section 3: Configuration Preset List: To add a preset to the sequence, select it from the drop- down box at the bottom of this window, set the Dwell time to determine how long the camera view will stay at that preset, then click the Add button. The preset name will appear in the list, followed by the dwell time to view that preset for. You can rearrange your presets in the sequence by selecting a preset in the sequence, then clicking the arrow buttons to move it higher or lower in the current sequence. Clicking the trash can button will remove the currently selected preset from the sequence. If you want to change the dwell time for a preset, select it from the list, enter a new dwell time, then click the Update button.

Section 3: Configuration Motion Detection Motion detection enables the camera to monitor the video feed for movement. Here, you can adjust the sensitivity settings that determine whether motion is detected by the camera or not. After making any changes, click the Save Settings button to save your changes. Enable Video Motion: Sensitivity: Draw Motion Area: Erase Motion Area: Select this box to enable the motion detection feature of your camera. Specifies how sensitive motion detection will be from 0% to 100%. A low sensitivity setting means that there must be large changes between two images in order to detect motion, and a high sensitivity setting means that even small changes will cause motion to be detected. Use your mouse to click and drag on the areas that you would like to monitor for motion. To erase a motion detection area, simply click on the red square that you wish to remove. Right click on the camera image to bring up the following menu options: Select All: Draws a motion detection area over the entire screen. Clear All: Clears any motion detection areas that have been drawn. Restore: Restores the previously specified motion detection areas.

Section 3: Configuration Time and Date This section allows you to automatically or manually configure, update, and maintain the internal system clock for your camera. After making any changes, click the Save Settings button to save your changes. Time Zone: Enable Daylight Saving: Auto Daylight Saving: Set Date and Time Manually: Offset: Synchronize with NTP Server: NTP Server: Set the Date and Time Manually: Copy Your Computer's Time Settings: Select your time zone from the drop-down menu. Select this to enable Daylight Saving Time. Select this option to allow your camera to configure the Daylight Saving settings automatically. Selecting this option allows you to configure the Daylight Saving date and time manually. Sets the amount of time to be added or removed when Daylight Saving is enabled. Enable this feature to obtain time automatically from an NTP server. Network Time Protocol (NTP) synchronizes the DCS-4701E with an Internet time server. Choose the one that is closest to your location. This option allows you to set the time and date manually. This will synchronize the time information from your PC.

Section 3: Configuration Event Setup In a typical application, when motion is detected, the DCS-4701E sends images to a FTP server or via e-mail as notifications. As shown in the illustration below, an event can be triggered by many sources, such as motion detection. When an event is triggered, a specified action will be performed. You can configure the Network Camera to send snapshots or videos to your e-mail address or FTP site. To start plotting an event, it is suggested to configure server and media columns first so that the Network Camera will know what action shall be performed when a trigger is activated. ex. Motion detection, Periodically, Digital input, System reboot Event Condition ex. Snapshot, Video Clips ex. Email, FTP Media (what to send) Server (where to send) Action

Section 3: Configuration The Event Setup page includes 4 different sections. • Event • Server • Media • Recording 1. To add a new item server, media, event, or recording item click Add. A screen will appear and allow you to update the fields accordingly. 2. To delete the selected item from the server, media, event, or recording drop-down menus, click the Delete button next to it. 3. Click on an item to edit it. Add Server Server Name: E-mail: FTP: Network Storage: Enter the unique name of your server. Enter the configuration for the target e-mail server account. Enter the configuration for the target FTP server account. Specify a network storage device. Only one network storage device is supported. You can configure up to 5 servers to save snapshots and/or video to. After making any changes, click the Save Settings button to save your changes.

Section 3: Configuration Add Media Media Name: Snapshot: Source: Send pre-event image(s) [0~4]: Send post-event image(s) [0~7]: File name prefix: Enter a unique name for media type you want to create. Select this option to set the media type to snapshots. Set the video profile to use as the media source. Refer to "Video" on page 32 for more information on video profiles. Set the number of pre-event images to take. Pre-event images are images taken before the main event snapshot is taken. Set the number of post-event images to take. Post-event images are images taken after the main event snapshot is taken. You can set up to 7 post-event images to be taken. For example: If both the Send pre-event images and Send post-event images are set to four, a total of 9 images are generated after a trigger is activated. The prefix name will be added to the file name. There are three types of media: Snapshot, Video Clip, and System Log. After making any changes, click the Save Settings button to save your changes. 1 pic. 2 pic. 3 pic. 4 pic. 5 pic. 6 pic. 7 pic. 8 pic. 9 pic. The moment the trigger is activated.

Section 3: Configuration Add date and time suffix to file name: Video clip: Source: Pre-event recording: Maximum duration: Maximum file size: File Name Prefix: System log: SNAPSHOTS20080104_100341 Date and time suffix The format is: YYYYMMDD_HHMMSS File name prefix Check this to add the date and time the snapshot was recorded as a file name suffix. Select this option to set the media type to video clips. Set the video profile to use as the media source. Refer to "Video" on page 32 for more information on video profiles. This sets how many seconds to record before the main event video clip starts. You can record up to 4 seconds of pre-event video. Set the maximum length of video to record for your video clips. Set the maximum file size to record for your video clips. This is the prefix that will be added to the filename of saved video clips. Select this option to set the media type to system logs. This will save the event to the camera system log, but will not record any snapshots or video.

Section 3: Configuration Add Event Create and schedule up to 3 events with their own settings here. After making any changes, click the Save Settings button to save your changes. Event name: Enable this event: Priority: Delay: Trigger: Video Motion Detection: Periodic: System Boot: Network Lost: Time: Action: Enter a name for the event. Select this box to activate this event. Set the priority for this event. The event with higher priority will be executed first. Select the delay time before checking the next event. It is being used for both events of motion detection and digital input trigger. Specify the input type that triggers the event. Motion is detected during live video monitoring. Select the windows that need to be monitored. The event is triggered in specified intervals. The trigger interval unit is in minutes. Triggers an event when the system boots up. Triggers an event when the network connection is lost. Select Always or enter the time interval to monitor for the specified kind of event. If you have created Server and Media entries, you will see them appear here. Select which Server you want to send to and which Media you want the camera to send.

Section 3: Configuration Add Recording Recording entry name: Enable this recording: Priority: Source: Recording schedule: Destination: Total cycling recording size: Enter a name for the recording. Select this to enable the recording function. Set the priority for this entry. An entry with a higher priority value will be executed first. Select the video profile to use as the recording source. Use the checkboxes to set which days to record video on. Select Always to record for the entire day, or select From and select what period of time you want to record using the dropdown boxes. Select the folder where the recording file will be stored. Please input a HDD volume between 1MB and 2TB for recording space. The recording data will replace the oldest record when the total recording size exceeds this value. For example, if each recording file is 6MB, and the total cyclical recording size is 600MB, then the camera will record 100 files in the specified location (folder) and then will delete the oldest file and create new file for cyclical recording. Please note that if the free HDD space is not enough, the recording will stop. Before you set up this option please make sure your HDD has enough space, and it is better to not save other files in the same folder as recording files. Here you can configure and schedule the recording settings. After making any changes, click the Save Settings button to save your changes.

Section 3: Configuration Size of each file for recording: Time of each file for recording: File Name Prefix: If this is selected, files will be separated based on the file size you specify. If this is selected, files will be separated based on the maximum length you specify. The prefix name will be added on the file name of the recording file(s).

Section 3: Configuration Advanced ICR and IR Here you can configure the ICR and IR settings. The IR (Infrared) Cut-Removable (ICR) filter can be disengaged for increased sensitivity in low light environments. Automatic: Day Mode: Night Mode: Schedule Mode: IR Light Control: Off: On: Sync with ICR: Schedule: The Day/Night mode is set automatically. You can use the Sensitivity drop-down box to set when the camera will switch to Night mode. The text box to the right shows what lighting conditions are currently being detected by the camera for reference. You can refresh this status by clicking the Refresh button. Day mode enables the IR Cut Filter. Night mode disables the IR Cut Filter. Set up the Day/Night mode using a schedule. The camera will enter Day mode at the starting time and return to Night mode at the ending time. The camera can enable or disable the IR (infrared) light according to your preferences. This setting provides additional controls depending on your specific application. The IR light will always be off. The IR light will always be on. The IR light will turn on when the ICR filter is disabled (night mode). The IR light will turn on or off according to the schedule that you specify below.

Section 3: Configuration HTTPS This page allows you to install and activate an HTTPS certificate for secure access to your camera. After making any changes, click the Save Settings button to save your changes. Enable HTTPS Secure Connection: Create Certificate Method: Status: Note: Enable the HTTPS service. Choose the way the certificate should be created. Three options are available: ƒƒ Create a self-signed certificate automatically ƒƒ Create a self-signed certificate manually ƒƒ Create a certificate request and install Displays the status of the certificate. The certificate cannot be removed while HTTPS is still enabled. To remove the certificate, you must first uncheck Enable HTTPS secure connection.

Section 3: Configuration Access List Here you can set access permissions for users to view your DCS-4701E. Allow list: Start IP address: End IP address: Delete allow list: Deny list: Delete deny list: The list of IP addresses that have access rights to the camera. Note: When adding entries to the Allow list, make sure the first entry includes the IP address of the computer or device you are using to access the camera. Otherwise, you may be blocked from accessing the camera after adding the entry to the Allow list. The starting IP address of the IP address range for the devices (such as a computer) that have permission to access the video of the camera. The ending IP address of the IP address range for the devices (such as a computer) that have permission to access the video of the camera. Click Add to save your changes. Note: A total of seven lists can be configured for both columns. Select an entry to remove from the Allow List, then click Delete. The list of IP addresses that have no access rights to the camera. Select an entry to remove from the Deny List, then click Delete. Note: All addresses in the Deny List will be denied access, even if they are also in the Allow List.

Section 3: Configuration SNMP Here you can set the SNMP settings for the camera, which allow for SNMP management of the camera. Enable SMNPv1, SNMPv2c: Read/Write Community: Read Only Community: Enable SNMPv3: Read/Write Security Name: Authentication Type: Authentication Password: Encryption Password: Read Only Security Name Enable this option to allow for SNMPv1 and SNMPv2c management of the camera. Enter a name for the read/write community of your SNMP server. Enter a name for the read-only community of your SNMP server. Enable this option to allow SNMPv3 management of the camera. Enter a name for the read/write community of your read/ write SNMP server. Enter the type of authentication used by your read/write SNMP server. Enter the authentication password used for your read/ write SNMP server. Enter the encryption password used for your read/write SNMP server. Enter a name for the read-only community of your read- only SNMP server.

Section 3: Configuration Enter the type of authentication used by your read-only SNMP server. Enter the authentication password used for your read- only SNMP server. Enter the encryption password used for your read-only SNMP server. Authentication Type: Authentication Password: Encryption Password:

Section 3: Configuration Maintenance Device Management You may modify the name and administrator’s password of your camera, as well as add and manage the user accounts for accessing the camera. You may also use this section to create a unique name and configure the OSD settings for your camera. Admin Password Setting: Add User Account: User Name: Password: User List: IP Camera Name: Enable OSD: Label: Show Time: LED: Set a new password for the administrator’s account. Add a new user account. Enter the user name for the new account. Enter the password for the new account. All the existing user accounts will be displayed here. You may delete accounts included in the list, but you may want to reserve at least one as a guest account. Create a unique name for your camera that will be added to the file name prefix when creating a snapshot or a video clip. Select this option to enable the On-Screen Display feature for your camera. Enter a label for the camera, which will be shown on the OSD when it is enabled. Select this option to enable the time-stamp display on the video screen. You may specify whether or not to illuminate the status LED on the camera.

Section 3: Configuration System In this section, you may backup, restore and reset the camera configuration, or reboot the camera. Save To Local Hard Drive: Load From Local Hard Drive: Restore to Factory Defaults: Reboot Device: Enable Schedule Reboot: You may save your current camera configuration as a file on your computer. Locate a pre-saved configuration by clicking Browse and then restore the pre-defined settings to your camera by clicking Load Configuration. You may reset your camera and restore the factory settings by clicking Restore Factory Defaults. This will restart your camera. If you want your camera to reboot on a regular schedule, check the Enable Schedule Reboot checkbox, then select the days and time you want the camera to reboot on.

Section 3: Configuration Firmware Upgrade The camera's current firmware version will be displayed on this screen. You may visit the D-Link Support Website to check for the latest available firmware version. To upgrade the firmware on your DCS-4701E, please download and save the latest firmware version from the D-Link Support Page to your local hard drive. Locate the file on your local hard drive by clicking the Browse button. Select the file and click the Upload button to start upgrading the firmware. Current Firmware Version: Current Product Name: File Path: Upload: Displays the detected firmware version. Displays the camera model name. Locate the file (upgraded firmware) on your hard drive by clicking Browse. Uploads the new firmware to your camera.

Section 3: Configuration Status Device Info This page displays detailed information about your device and network connection.

Section 3: Configuration This page displays the log information of your camera. You may download the information by clicking Download. You may also click Clear to delete the saved log information. Logs

Section 3: Configuration This page provides helpful information regarding camera operation. Help

Appendix A: Technical Specifications Technical Specifications Camera Camera Hardware Profile ƒƒ 1/3" 1.3 Megapixel progressive CMOS sensor ƒƒ 30 meter IR illumination distance ƒƒ Minimum illumination: 0 lux with IR LED on ƒƒ Built-in Infrared-Cut Removable (ICR) Filter module ƒƒ 10x digital zoom ƒƒ Minimum object distance 0.2M ƒƒ Focal length: 2.8 mm ƒƒ Aperture: F1.8 ƒƒ Angle of view: ƒƒ (H) 96° ƒƒ (V) 54° ƒƒ (D) 108° Camera Housing ƒƒ IP-66 compliant weatherproof housing Image Features ƒƒ Configurable image size, quality, frame rate, and bit rate ƒƒ Time stamp and text overlays ƒƒ Configurable motion detection windows ƒƒ Configurable privacy mask zones ƒƒ Configurable shutter speed, brightness, saturation, contrast, and sharpness Video Compression ƒƒ Simultaneous H.264/MJPEG format compression ƒƒ H.264/MJPEG multicast streaming ƒƒ JPEG for still images Video Resolution 16:9 - 1280 x 720, 800 x 448, 640 x 360, 480 x 272, 320 x 176 up to 30 fps 4:3 - 960 x 720, 800 x 592, 640 x 480, 480 x 352, 320 x 240 up to 30 fps External Device Interface ƒƒ 10/100 BASE-TX Fast Ethernet port ƒƒ Supports 802.3af PoE Network Network Protocols ƒƒ IPv6 ƒƒ IPv4 ƒƒ TCP/IP ƒƒ UDP ƒƒ ICMP ƒƒ DHCP client ƒƒ NTP client (D-Link) ƒƒ DNS client ƒƒ DDNS client (D-Link) ƒƒ SMTP client ƒƒ FTP client ƒƒ HTTP / HTTPS ƒƒ Samba client ƒƒ PPPoE ƒƒ UPnP port forwarding ƒƒ RTP / RTSP/ RTCP ƒƒ IP filtering ƒƒ QoS ƒƒ CoS ƒƒ Multicast ƒƒ IGMP ƒƒ ONVIF compliant Security Administrator and user group protection Password authentication HTTP and RTSP authentication

Appendix A: Technical Specifications System Management System Requirements for Web Interface ƒƒ Browser: Internet Explorer, Firefox, Chrome, Safari Event Management ƒƒ Motion detection ƒƒ Event notification and uploading of snapshots/video clips via e-mail or FTP ƒƒ Supports multiple SMTP and FTP servers ƒƒ Multiple event notifications ƒƒ Multiple recording methods for easy backup Remote Management ƒƒ Take snapshots/video clips and save to local hard drive ƒƒ Configuration interface accessible via web browser D-ViewCam™ System Requirements ƒƒ Operating System: Microsoft Windows 8/7/Vista ƒƒ Web Browser: Internet Explorer 7 or higher ƒƒ Protocol: Standard TCP/IP D-ViewCam™ Software Functions ƒƒ Remote management/control of up to 32 cameras ƒƒ Viewing of up to 32 cameras on one screen ƒƒ Supports all management functions provided in web interface ƒƒ Scheduled motion triggered, or manual recording options General Weight 445 g ± 5% External Power Adapter (not included) Input: 100 to 240 V AC, 50/60 Hz Output: 12 V DC 1.5 A Power Consumption 4.7 watts ± 5% Temperature Operating: -30 to 50 °C (-22 to 122 °F) Storage: -20° to 70° C (-4° to 158° F) Humidity Operating: 20% to 80% non-condensing Storage: 5% to 95% non-condensing Certifications CE CE LVD FCC C-Tick

Appendix A: Technical Specifications Dimensions Ø 65 164.7 66.6 98.1