Datalogic DS2400A Manual 

DS2400A General View: Laser Safety: The scanner is classified as a Class 2 laser product according to EN 60825-1 regulations and as a Class II laser product according to CDRH regulations. Disconnect the power supply when opening the device during maintenance or installation to avoid exposure to hazardous laser light. There is a safety device which allows the laser to be switched on only if the motor is rotating above the threshold for its correct scanning speed. The motor and laser beam can be switched off through a software command (see also the WinHost Help On Line). CAUTION-CLASS 3B LASER LIGHT WHEN OPEN AVOID EXPOSURE TO BEAM This product conforms to the applicable requirements of 21CFR1040 at the date of manufacture. LASER LIGHT DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT MAX. OUTPUT RADIATION 1 mW EMITTED WAVE LENGTH 630~680 nm TO EN 60825-1:2001 R C US 218441 N2468 Figure A 1 2 3 4 8 7 6 5 Power On / Data TX LED External Trigger LED Good Read LED Laser On LED Warning and Device Class Label Laser Beam Output Window Accessory Mounting Holes Mounting Holes For further details on product installation, see the complete Reference Manual on the installation CD-ROM. DS2400A can be configured through the WinHost Windows-based software program available on the installation CD-ROM. For configuration it is necessary to create a cable connecting the scanner to the PC as indicated in the “How To Build A Simple Interface Test Cable” section of this guide, otherwise you can use the C-Box 100. Power Supply: - This product is intended to be installed by Qualified Personnel only. - All Models: This accessory device is intended to be supplied by a UL Listed or CSA Certified Power Unit with «Class 2» or LPS power source which supplies power directly to the scanner via the 25-pin connector. Warning and Device Class Labels The laser diode used in this device is classified as a class 3B laser product according to EN 60825-1 regulations and as a Class IIIb laser product according to CDRH regulations. As it is not possible to apply a classification label on the laser diode used in this device, the following label is reproduced below. LASER LIGHT AVOID EXPOSURE TO BEAM CLASS 3B LASER PRODUCT MAX. OUTPUT RADIATION 7 mW EMITTED WAVE LENGTH 630~680 nm TO EN 60825-1 (2001) Laser Diode Class Label Any violation of the optic parts in particular can cause radiation up to the maximum level of the laser diode (7 mW at 630 to 680 nm). WEEE Compliance: 7 6 5 1 2 3 4 8

2 Model Description: DS2400A - X X X 0 Reading Range 0 = Short range 1 = Medium range 2 = Long range Communication Interface 2 = RS232/RS485 main + RS232 aux Optic Version 0 = Linear 1 = Raster Reading Performance: Version Reading Distance Max Code Resolution mm (mils) Speed scans/s 0XX0 75 mm (3 in) - 340 mm (13.4 in) on 0.35 mm (14 mils) codes 0.20 (8) 600 to 1000 1XX0 100 mm (3.9 in) - 440 mm (17.3 in) on 0.50 mm (20 mils) codes 0.25 (10) 600 to 1000 2XX0 190 mm (7.5 in) - 600 mm (23.6 in) on 0.50 mm (20 mils) codes 0.35 (14) 600 to 1000 Technical Features: ELECTRICAL FEATURES SOFTWARE FEATURES Power Supply 10 –30 Vdc Readable Codes Power Consumption 5 W maximum Main Serial Interface Programmable: RS232; RS485 Full-Duplex/Half- Duplex; Auxiliary Interface RS232 * * * * * * * EAN/UPC (including Add-on 2 and Add-on 5) Code 39 2/5 Interleaved Code 128 EAN 128 Codabar Code 93 Baudrates 150 to 115200 * = ACB readable ISBT 128 Inputs Pharmacode External Trigger (optocoupled NPN or PNP) Headers and Up to four header and four Voltage max. 30 Vdc Terminators terminator characters Current Consumption 25 mA Operating Modes On-Line, Automatic, max. Serial-On-Line, Test Outputs) Configuration Modes Through menus using: OUT1, OUT2 (optocoupled) WinHost utility Host Mode (commands from VCE max. 40 Vdc one of the serial ports) Collector Current 40 mA continuous; Code Selection Up to six different codes max. 130 mA pulsed during one reading phase VCE Saturation 1V at 10 mA max. Decoding Safety Can enable multiple good Power Dissipation 90 mW at 40 °C reads of the same code max. (Ambient temp.) Special Functions ACB (Advanced Code Builder) Motor Off OPTICAL FEATURES Parameter Storage Non-volatile internal EEPROM Light Source semiconductor laser diode ENVIRONMENTAL FEATURES Wavelength In the range 630 to 680 nm Operating 0° to +40 °C (+32° to +104 °F) Safety Class Class 2 - EN 60825-1; CDRH Temperature Storage -20° to +70 °C (-4° to +158 °F) USER INTERFACE Temperature LED Indicators Laser ON, Good Read, Humidity max 90% non condensing External Trigger, Vibration Resistance 14 mm @ 2 to 10 Hz; Data TX / Power ON IEC 68-2-6 test FC 1.5 mm @ 13 to 55 Hz; 2 G @ 70 to 200 Hz; PHYSICAL FEATURES 2 hours on each axis Dimensions 68x83.6x34 mm (2.7x3.29x1.3 in) Shock Resistance 30 G; Weight 330 g. (11.64 oz) IEC 68-2-27 test EA 11 ms; 3 shocks on each axis Protection Class IP65

3 Accessories: Name Description Part Number GFC-2100 90° Reading Device 93A201000 GFC-2000 105° Reading Device 93A201080 OM2000 Oscillating Mirror 93A251031 INT-30 (for C-Box 100) 20 mA Current Loop Interface Board 93A151022 C-BOX 100/200 Connection Box 93ACC1510, 93ACC1520 C-BOX 300/310 Connection Box Profibus 93A301000, 93A301030 C-BOX 400/410 Connection Box DeviceNet 93A301010, 93A301040 MEP-542/543 Photocell Kit NPN/PNP 93ACC1727, 93ACC1728 Electrical Connections: DS2400A is equipped with a cable terminated by a 25-pin female D-sub connector for connection to the power supply, communication interface and input/output signals. You can bring system cables directly to the 25-pin connector or you can connect the scanner directly to one of the various C-Box models and bring system wiring to it (see the relative C-Box Installation Manual). CAUTION Do not connect GND and SGND to different (external) ground references. GND and SGND are internally connected through filtering circuitry which can be permanently damaged if subjected to voltage drops over 0.8 Vdc. The details of the connector pins are indicated in the following table: 25-pin D-sub female connector pinout Pin Name Function 13 VS Power supply input voltage + 25 GND Power supply input voltage - 1 CHASSIS Chassis Ground 9 VS External Trigger supply voltage + 18 EXT TRIG+ External Trigger + 19 EXT TRIG- External Trigger - 8 OUT1 + Output 1 + 11 OUT2 + Output 2 + 12, 22 OUT REF Output reference 20 RXAUX Auxiliary RS232 21 TXAUX Auxiliary RS232 23 CTSAUX Auxiliary handshake RS232 24 RTSAUX Auxiliary handshake RS232 6, 10, 14, 15, 16, 17 NC Not Connected 25-pin female connector Pin RS232 RS485 Full-Duplex RS485 Half-Duplex 2 TX232 TX485+ RTX485+ 3 RX232 RX485+ 4 RTS232 TX485- RTX485- 5 CTS232 RX485- 7 SGND SGND SGND

4 Mechanical Installation: 23.3* 0.92 14 0.55 84 3.31 4 0.16 10.3 0.41 40 1.57 0.41 10.3 40 1.57 14.7 0.58 M 4 n° 4 1.29 32.7 mm inch 68 2.68 46 1.81 DS2100A 9 4.2 7.8 20° 2.5 73 42 R 40 4.2 90° 30 13.8 17.5 2.5 23 mm 4.2 n° 2 1 x 45° n° 2 * The quote refers to the scan line Input/Output Connections: INPUT NPN INPUT NPN MEP-543 EXT TRIG+ 18 19 + 5V DS2400A EXTERNAL TRIGGER Signal V Vext 30 Vdc max. EXT TRIG- Input NPN command using external power MEP-543 Connector DS2400A 18 19 + 5V VS 9 25 GND EXT TRIG+ EXT TRIG- 4 3 2 1 (brown) (white) (blue) Input NPN command using MEP-543 Photocell OUTPUT EXTERNAL TRIGGER DS2400A Signal 18 19 + 5V VS 9 25 GND Ground V EXT TRIG+ EXT TRIG- Input NPN command using DS2400A power USER INTERFACE + 8/11 12/22 OUT REF DS2400A Vext 40 Vdc max. C E Output open collector connections INPUT PNP 18 19 + 5V DS2400A EXTERNAL TRIGGER V Signal Ground EXT TRIG+ EXT TRIG- Vext 30 Vdc max. Input PNP command using external power VCE max = 40 Vdc I max = 40 mA continuous EXTERNAL TRIGGER DS2400A 18 19 + 5V VS 9 25 GND Ground V Signal EXT TRIG+ EXT TRIG- Input PNP command using DS2400A power DS2400A

5 Connectivity: RS232 Main Interface Connections RS485 Main Interface Connections RS232 Point-to-point layout RS485 Point-to-point layout c Main Serial Interface (RS232) c Main Serial Interface (RS485 Full Duplex) dAuxiliary Serial Interface (Local Echo) (RS232) dAuxiliary Serial Interface (Local Echo) (RS232) eExternal Trigger (for On-Line Mode) eExternal Trigger (for On-Line Mode) Pass-through layout Multiplexer layout c Main Serial Interface (RS232) c Main Serial Interface (RS485 Half-Duplex) dAuxiliary Serial Interface (RS232) dAuxiliary Serial Interface (Local Echo) (RS232) eExternal Trigger (for On-Line Mode) eExternal Trigger (for On-Line Mode) RS232 Master/slave layout RS485 Master/slave layout c Main Serial Interface (Slaves RS232 only) c Auxiliary Serial Interface (RS232) dAuxiliary Serial Interface (RS232) d Main Serial Interface (RS485 Half-Duplex) eExternal Trigger (for On-Line Mode) eExternal Trigger Host MX4000 Host DS2400A Terminal Host DS2400A Terminal Host DS2400A DS2400A Host DS2400A Slave DS2400A Slave DS2400A Master Host DS2400A Slave DS2400A Slave DS2400A Master