Crypto F200 Operation & User’s Manual

1. Introduction 4 2. Specifications 4 2.1 ADSL Standards supported 4 2.2 Supported Protocols 4 2.3 Connections 5 3. Hardware Installation Procedures 5 3.1 Hardware Requirements 5 3.2 Preparing your network information 5 3.3 Configure the ISP parameters for your Windows XP 6 3.4 Driver Installation on Windows XP 7 3.5 Software Configuration 8 3.6 Connection to the Internet 11 4. Troubleshooting 13 ...

provides a full rate ADSL modem with the superb reliability and is a complete solution for home and office. The F200 ADSL USB modem can have a maxi- mum downstream data rate of up to 8Mbps and an upstream of up to 1Mbps. You can safely enjoy the new generation broadband Internet with the F200 ADSL USB modem. Included drivers for Win98/ ME/ 2000/ XP. 2. Specifications 2.1 A ...

USB port of the computer. LINE – Connects the RJ11 telephone cable from the telephone line port of F200 modem to the telephone plug.. LED indications: POWER: After successfully installing the modem, the POWER LED light turns on. It will stay on every time you start your computer. 3. Hardware Installation Procedures 3.1 Hardware Requirements The following hardware i ...

Information Value PVC Settings VPI VCI Encapsulation (LLC ‹ VCMux) Login Username Information Password Line Modulation Automatic ITU G.dmt or G.lite preferred Automatic ANSI T1.413 i2 preferred ITU (G.dmt or G.lite) G.dmt G.lite table 4 LAN (Bridged/Routed/IPoA parameters) Information Value PVC Settings VPI VCI Encapsulation (LLC or VC Mux) IP Information IP Address Subnet Mask Gateway IP Address Preferred DNS address ...

Step 1: Windows will detect the newly installed device and the screen below will appear after the F200 USB ADSL Modem is attached to the systems USB port. Select "Install from a specific Location", and click "NEXT". Step 2: Select "Include this location in the search" and type d:\driver\Wan (where D:\ the CD-ROM) Note: If the protocol being used is Bridged, Routed or IpoA, then type d:\driver\Lan Step 3: Click Continue ...

click on 'Properties_ > _Device Manager' Double click on Network adapters and check to see for: 'Crypto F200 USB ADSL WAN adapter' 3.5 Software Configuration Continue the setup process of the F200. Step 1: Double click on the ‘Access Runner’ icon Step 2: Initially there is no connection / synchronization with the ADSL line ‘Attempting to Activate Line’. Press ‘ALT – P’ on you ...

not been established. ‘Attempting to Activate Line’. Click the ‘Line Setup’ tab Step 4: Initially it is set to Annex B (ADSL over ISDN) as shown on the bottom right. Note: If the line was ISDN, then we do not change it. Step 5: Select Annex A (ADSL over POTS) (given that the line was PSTN). Click Apply. Note: Incase you take out the USB plug from your computer and plug it back to the USB port of the ...

VPI = 8 VCI = 35 Click Apply. Step 8: For Encapsulation Mode select the connection protocol: PPP over ATM VCMUX (RFC2364) Click Apply Click on the General tab Step 9: Under Line Status, the indication ADSL Connection Established, indicates that the connection / synchronization with the ADSL line has been done with success. Note: 1 to 2 minutes are required after you make the above configurations, in order for the F200 to be ...

ADSL Connection Established indicates that the connection / synchronization with the ADSL line has been done with success. Note: After power on the PC, it takes 1 to 2 minutes in order for the F200 to be synchronized with the ADSL line. 3.6 Connection to the Internet Step 1: To connect to the Internet, double click on the Connect Access Runner DSL icon which is found on the Desktop Step 2: Insert the "User Login & Pas ...

installed, under the General tab, check to see that Connected is indicated next to Status. You can also check your connection speed: Speed -> 448.0kbps. Step 5: Under the Details tab, you can see various information regarding the connection. (i.e. Server Type, Server IP address etc.). 12 ...

ñCheck to see that the connections between the USB port of the F200 and the USB port of your computer are plugged in correctly. Cannot access ISP ñIf in PPPoA & PPPoE mode, check your login account and password for the remote server. ñCheck your VPI/VCI value and encapsulation mode are the same as your ISP gave you. ñTry to dial the phone to check if the phone line to CO is good if telephone service is availab ...

The 'F200 ADSL USB MODEM' is approved for use for within the European Union, and the compatibility of this unit and it’s basic requirements are declared with the CE symbol. Passage extract of the authentic declaration of conformity: CE Verification of Compliance Technical Standards: EMC: ETSI EN 300 386 v1.3.2/2002.12 LVD: EC LOW VOLTAGE DIRECTIVE 73/23/EEC, 93/68/EEC Measurement standards: (1) EN 55022 : 1998 (2) EN 61000- ...