BE BE-3100PR Operation Manual

Introduction 4  Using the Operators Manual Product Identification 5  Generator 5  Engine Safety 6  Safety Rules 6  Hazard Symbols and Meanings 9 Ground Fault Circuit Interrupter Protection Generator Components 13  3500W Component Chart 14  6500W Component Chart 15  9000W Component Chart Preparing the Generator 16  Grounding the Generator Pre-Operation Checklist 17  Engine Oil 17  Fuel 18  General Recommendations 18  Fuel Type 18  Gasoline/Alcohol Blends 18  Gasoline/Ether Blends 18  Check Component Parts 19  Check Generator Surroundings Starting the Generator 19  Recoil Start 21  E ...

Operation 22  Using Electric Power 22  AC Application 23  DC Application 23  Connection of Cable 23  Safety Precautions While Charging 24  Wattage Information 25  Spark Arrester 25  How To Remove The Spark Arrester 25  Clean The Spark Arrester Screen Stopping the Generator 26  Stopping the Generator 26  Oil Sensor Troubleshooting 27  Troubleshooting Chart Maintenance 28  Maintenance Schedule 28  Daily Inspection 28  Periodic Maintenance 29  Changing Engine Oil 29  Servicing The Air Cleaner 29  Cleaning and Gapping Spark Plug 29  Cleaning Fuel Strainer 29  Periodic Operation and Inspection Tran ...

The operating manual is an important part of your generator and should be read thoroughly before initial use, and referred to often to make sure adequate safety and service concerns are being addressed. Reading the owner’s manual thoroughly will help avoid any personal injury or damage to your machine. By knowing how best to operate this machine you will be better positioned to show others who may also operate the unit. This manual contains information for the complete range of BE generators, and was written to take you from the safety requirements to the operating functions of your machine. You can refer back to the ...

Generator If you need to contact an Authorized Dealer or Customer Service line (1-866-850-6662) for information on servicing, always provide the product model and identification numbers. You will need to locate the model and serial number for the machine and record the information in the places provided below. Date of Purchase: Dealer Name: Dealer Phone: Product Identification Numbers Model Number: Serial Number: ...

CAUTION, WARNING), a pictorial and/or a safety message to alert you to hazards. DANGER indicates a hazard which, if not avoided, will result in death or serious injury. WARNING indicates a hazard which, if not avoided, could result in death or serious injury. CAUTION indicates a hazard which, if not avoided, might result in minor or moderate injury. NOTICE indicates a situation that could result in equipment damage. Follow safety messages to avoid or reduce the risk of injury or death. Hazard Symbols and Meanings Save these Instructions Safety Rules safety This is the safety alert s ...

poisonous gas that can kill you. You CANNOT smell or see this gas. • Use the generator outdoors, away from open windows, vents, or doors that could allow the carbon monoxide gas to come indoors. Keep the generator at least 1 meter (3 feet) away from any structure or building during use. • NEVER use a generator indoors, including in homes, garages, basements, crawl spaces, and other enclosed or partially-enclosed areas, even with ventilation. Opening doors and windows or using fans will not prevent carbon monoxide build-up in the home. • Never use a generator in enclosed or ...

explosive. Fire or explosion can cause severe burns or death. When Adding or Draining Fuel • Observe all safety regulations for the safe handling of fuel. Handle fuel in safety containers. If the container does not have a spout, use a funnel. • Do not overfill the fuel tank, leave room for the fuel to expand. • Do not refill fuel tank while the engine is running. Before refueling the generator, turn it off and let it cool down. Gasoline spilled on hot engine parts could ignite. • Fill the tank only on an area of bare ground. While fueling the tank, keep heat, sparks and ...

grounded. Follow the correct procedure specified in the section labeled GROUNDING INSTRUCTIONS. Ground Fault Circuit Interrupter Protection These generators are equipped with a GFCI (Ground Fault Circuit Interrupters) 120V duplex receptacles for protection against the hazards of electrical shock from defective attachments such as, tools, cords, and cables. A GFCI is a device that interrupts electricity from either the utility or generator by means of a special type of circuit breaker that determines if a current flow to the ground occurs. A GFCI can be used only with generators ...

tion. Check with a qualified electrician for your local requirements if you are in doubt as to whether the unit is properly grounded. This generator is equipped with a grounding terminal for added protection. Using the ground path from the generator to an external ground source as instructed in the section labeled “Grounding Instructions” in the Preparation section of this manual can be necessary. Please consult a qualified electrician for local regulations. The generator is a potential source of electrical shock if not kept dry. Keep the generator dry and do not use in rain or ...

overheated if it is enclosed. If generator has been covered to protect if from the weather during non use, be sure to remove it and keep it well away from the area during generator use. • Operate the generator on a level surface. It is not necessary to prepare a special foundation for the generator. However, the generator will vibrate on an irregular surface, so choose a level place. If the generator is tilted or moved during operation, fuel may spill and/or the generator may tip over, causing a hazardous situation. Proper lubrication cannot be expected i ...

• It is absolutely essential that you know the safe and proper use of the power tool or appliance that you intend to use. All operators must read, understand and follow the tool / appliance owners manual. Tool and appliance applications and limitations must be understood. Follow all directions given on labels and warnings. Keep all instruction manuals and literature in a safe place for future reference. • Use only “LISTED” extension cords. When a tool or appliance is used outdoors, use only extension cords marked “For Outdoor Use”. Extension cord ...

rules before operating your generator. generator components BE-3100PR 3500watt 1. Control Panel 2. Fuel Tank 3. Fuel Gauge 4. Oil Drain Plug 5. Recoil Starter 6. Tank Cap 7. Frame 8. Air Cleaner 9. ON/OFF Switch 1. 14. 15. 16. 5. 8. 4. 9. 10. 13. 17. 12. 11. 2. 6. 7. 3. 10. DC Connection 11. DC Breaker 12. Voltmeter 13. 120V 3 Prong Twistlock 14. Ground 15. 120V GFCI 16. AC Breaker 17. Oil Dipstick ...

rules before operating your generator. generator components 1. Control Panel 2. Fuel Tank 3. Fuel Gauge 4. Oil Drain Plug 5. Recoil Starter 6. Tank Cap 7. Frame 8. Air Cleaner 9. Battery 10. ON/OFF Switch 11. Auto throttle 1. 17. 18. 19. 19. 15. 16. 9. 22. 5. 10. 20. 8. 4. 11. 12. 13. 21. 14. 2. 6. 7. 3. 12. DC Connection 13. DC Breaker 14. Voltmeter 15. 120V 3 Prong Twistlock 16. 240V 4 Prong Twistlock 17. Ground 18. 120V GFCI 19. AC Breaker 20. Wheel Kit 21. Oil Dipstick 22. Handles BE-6500ER 6500watt ...

rules before operating your generator. generator components 1. Control Panel 2. Fuel Tank 3. Fuel Gauge 4. Oil Drain Plug 5. Recoil Starter 6. Tank Cap 7. Frame 8. Air Cleaner 9. Battery 10. ON/OFF Switch 11. Auto throttle 1. 17. 18. 19. 19. 15. 16. 9. 22. 5. 10. 20. 8. 4. 11. 12. 13. 21. 14. 2. 6. 7. 3. 12. DC Connection 13. DC Breaker 14. Voltmeter 15. 120V 3 Prong Twistlock 16. 240V 4 Prong Twistlock 17. Ground 18. 120V GFCI 19. AC Breaker 20. Wheel Kit 21. Oil Dipstick 22. Handles BE-9000ER 9000watt ...

to a suitable ground source. The ground path should be made with #8 size wire. Connect the grounding wire securely to the ground terminal. Connect the other end of the wire securely to a suitable ground source. A metal underground water pipe in direct contact with the earth for at least 10 feet can be used as a grounding source. If a pipe is unavail- able, an 8 foot length of pipe or rod may be used as the ground source. The pipe should be 3/4” diameter or larger and the outer surface must be noncorrosive. If a steel or iron rod is used it should be at lea ...

level surface with engine stopped. This generator uses SAE 10W30 oil. 1. Remove oil dipstick and check the engine oil level. 2. If oil level is below the lower level line, refill with suitable oil to upper level line. Do not screw in the oil dipstick when checking oil level. 3. Change oil if contaminated. Fueling warning Explosive Fuel! Gasoline is extremely flammable and its vapors can explode if ignited. • Do not refuel while smoking or near open flame or other such potential fire hazards. • Store gasoline only in approved cont ...

2. Check fuel gauge while filling. 3. When using the generator for the first time or stopping due to the fuel running out, pull the recoil handle several times after filling the tank. General Recommendations • Purchase gasoline in small quantities and store in clean, approved containers. • To minimize gum deposits in your fuel system and to insure easy starting, do not use gasoline left over from the previous season. • Do not add oil to the gasoline. • Consider adding fuel stabilizer before running or starting the generator. Fuel Type • For best results use only cle ...

2. Move engine choke switch to the START (ON) position. (When the engine is warm or temperature is high, start engine with the switch in the OFF position). Recoil Start starting your generator CAution When starting the engine with the recoil start, set the toggle switch in the “ON” position before pulling the starter handle. CAution Do not connect appliances with defective power cords and/or plugs. Be sure appliances are not connected to generator when starting up. Starting the generator with an appliance connected could result in damage to the generator and/or appliances a ...

(resistance will be felt), then return the handle to its original position and pull briskly. starting your generator 4. After starting, allow the recoil starter handle to return to its original position with the handle still in your hand. NOTE: If the engine fails to start after several attempts, repeat the starting procedures mentioned above with the engine choke switch placed in the OFF position. 5. After 20 to 30 seconds of warm-up is completed, turn the engine choke switch to “OFF” position. 7. Test the GFCI receptacle on the unit. Push the test butt ...