APart-Audio SDQ5Pir Manual 

sound system. It consists of an amplified loudspeaker with a 5.25” woofer, a high frequency unit and a second linkable passive loudspeaker, powered by the second amplifier built into the active speaker. The speakers are magnetically shielded. The speakers can be remote controlled via the included infrared remote control, RS ...

power on and off. 2. Power cord inlet: attach the power cord supplied to this socket. The inlet also contains the mains fuse. 3. Multifunction led: this led is orange in standby mode, green when the speaker is active and red when an overload or clipping occurs. 4. Treble control: push the + or - button once to increase or decrease the treble tone control in ...

settings are 19200 Baudrate, 8 databits, no parity and 1 stop bit. The physical connection is as described below: Standard 9 pin serial cable, wired straight through (no null modem cable !!!). Maximum wire length depends on cable quality and influence from external interference. Pin 2: TX data: data transmission output Pin 3: RX data: data re ...

case, both inputs A and B will be mixed together by the SDQ5Pir unit. Possible values are A, B, AB or WI. WI is the local input of the optional wall control IPGAIN is input gain. Each source input has its own gain setting so the source (A, B or WI) needs to be specified. The value can be between 0 and 3 ...

The factory defaults are shown in the RS232 commands table. In order to restore the factory default settings, enter the following command: SET RESTORE ON This function can also be executed without using RS232 commands. In that case, power off the speaker. While pushing BASS + and - buttons on the rear panel simultaneously, power up the speaker with the power switch. The multifunction led will be orange. R ...

DEC OFF (-64) -63 to 0 0 MAXLVL Maximum allowed level GET, SET BACK, OFF (-64) -63 to 0 BACK BALANCE Left - right balance GET, SET -31 to 31 0 SELECT Source selection GET, SET A, B, AB, or WI AB EQBASS Equalizer bass GET, SET -14 to 14 0 EQTREB Equalizer treble GET, SET -14 to 14 0 STANDBY Standby state GET, SET ON or OFF OFF IPGAIN Input gain GET ...

If you don’t use the remote for an extended period of time, remove the battery and store it in a safe location. This will avoid possible damage or corrosion from battery leakage. Warning: Do not attempt to recharge, disassemble, or incinerate this type of battery. Keep all batteries away from children. Dispose of used batteries promptly and as regulated by applicable laws. The included infrared remote control unit ...

Infrared commands have been coded according to the NEC® protocol Function ir COMMAND Power ON 12 Power STANDBY 1A Input A 01 Input B 04 Input A + B 07 Input WALL 0A Level UP 03 Level Down 06 MUTE 09 Bass UP 0C Bass DOWN 00 Treble UP 0D Treble Down 0F ...

Input impedance minijack input A 5 k ohm Input sensitivity minijack input A 175 mV (-15dBV) Input impedance balanced input B 22 k ohm Input sensitivity balanced input B 175 mV (-15dBV) Tone control bass +- 14 dB @ 100 Hz in 2 dB steps Tone control treble +- 14 dB @ 10 kHz in 2 dB steps Balance control +- 31 steps ; 1.25 dB per step Input gain adjustment 0 to 3 ; + 3.75 d ...

damaged carton, please contact your dealer before opening the carton. • Read all documentation before operating your equipment. • Keep all documentation for future reference. • Save the carton and packing material even if the equipment has arrived in good condition. • Should you ever need to ship the unit, use only the origi ...

registered trademarks of their respective owners. © 2009 APart-Audio specifications subject to change without notice. ...