Aleratec 260167 Operation & User’s Manual

to change without notice. This manual is copyright with all rights reserved. Under copyright laws, this manual and the software described within may not be copied, except in the normal use of the product(s) described within or to make a backup copy. Copyright© 2010 Aleratec, Inc. 9851 Owensmouth Avenue Chatsworth, CA 91311 U.S.A. ww ...

The equipment described in this guide emits radio frequency energy. If it is not installed in accordance with the manufacturer’s instructions, it may cause interference with radio or television reception. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against ha ...

unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to authorized personnel only. CAUTION As the laser beam in this DVD/CD Duplicator is harmful to the eyes, do not attempt to disassemble the cabinet. Refer servicing to authorized personnel only. The use of optical instruments with this product will increase eye hazard. ...

Introduction........................................................................................1 Check out Aleratec Online!.....................................................................1 Key Items – 1:2 DVD/CD Copy Cruiser Pro HLX Win/Mac.................2 Front Panel...............................................................................................3 DVD/CD Copy Cruiser Pro HLX Win/Mac Display Pa ...

Mac. Please read this User Guide thoroughly before using this product. Page 3 shows the front panel of the 1:2 DVD/CD Copy Cruiser Pro HLX • Win/Mac. Page 4 shows the Duplicator LCD Display Panel. • Check out Aleratec Online! www.aleratec.com • www.twitter.com/Aleratec • www.youtube.com/Aleratec • ...

Mac Note: Choose a Good Location Allow adequate clearance for moving parts. 1. Do not place near heat sources such as radiators or air ducts, or in a 2. place subject to direct sunlight, excessive dust, mechanical vibration or shock. Good care will help assure maximum product life. Improper operating 3. environment and misuse may void the warranty. Display Panel LightScribe ...

This tray is for loading the disc. It will accept 120 mm and 80 mm discs. Please place the disc in the exact center of the tray. 2 Emergency Eject Pinhole In the event of loss of power or failure to open the tray by pressing the Eject button, insert the straightened end of a large paper clip or similar rigid object into the Emergency Eject hole to open the tray. 3 Drive LEDs This indicator lights u ...

1 Display shows all functions and messages 2 ENT button is used to execute a selected function 3 ESC button is used to cancel a selected function 4 UP arrow is used to scroll up through functions or menus 5 DOWN arrow is used to scroll down through functions or menus 4 1 3 5 2 ...

please read the following. Installation Avoid placing the 1:2 DVD/CD Copy Cruiser Pro HLX Win/Mac in a location subject to: High humidity • High temperature • Excessive dust • Mechanical vibration • Direct sunlight • Electromagnetic radiation • Operation Do not move the 1:2 DVD/CD Copy Cruiser Pro HLX Win/Mac during operation. This may cause it to mal ...

Cruiser Pro HLX Win/Mac. Detailed descriptions of each function are given in the next section. The functions are numbered for easy reference; these numbers are also used in the next section. There are 12 main menu items that will display in the 1:2 DVD/CD Copy Cruiser Pro HLX Win/Mac Display Panel. These are: Note: Main Menu items “Select Source� ...

These are: 10.1 CD to CD Edit 10.2 (Not supported) 10.3 Play Audio Track 10.4 Close Session 10. Edit Track ENT   ESC ...

The main menu “Setup” function has 18 subfunctions. These are: Note: Functions with options are indicated with an asterisk (*). 11.01 Language 11.02 CD Burn Speed 11.03 DVD Burn Speed 11.04 Read Speed (max.) 11.05 Auto Start Drive 11.06 Startup Menu 11.07 Auto Verify* 11.08 Auto Compare* 11.09 Auto Prescan* 11.10 Eject Disc* 11.11 Burn On The Fly* 11.12 Burn Mode* 11.13 Display Time 11.14 Button Soun ...

These are: Note: Functions with options are indicated with an asterisk (*). 12.01 UnderRun Protect* 12.02 Overburn* 12.03 Read Error Skip* 12.04 (Not supported) 12.05 (Not supported) 12.06 Burn-in 12.07 Update Firmware 12.08 Compare Firmware 12.09 Hardware Diagnostic 12.10 Load Default 12.11 CD+G Format (Not supported) 12.12 ISRC 12.13 CD-Text (Not supp ...

Inserting Discs Press the Eject button on the DVD/CD Recorder. 1. Place the disc in the tray. The printed (non-shiny) surface of the disc 2. should be up. To close the tray, press the Eject button or lightly push the front center 3. of the tray. Note: Never place two discs in the tray at the same time. • Do not touch the surface of the disc where it has been recorded. • When using a 120 mm disc, please pl ...

Power Up Sequence During the normal powering up sequence the 1:2 DVD/CD Copy Cruiser Pro HLX Win/Mac will preform a self-test sequence. Quick Operating Sequence Overview Select Copy function by pressing arrow button. Place the source DVD or • CD in the top drive. Place blank DVD-R/RW, DVD+R/RW, CD-R/RW, or CD-RW media in the DVD/CD-Recorder. After the recorder detects the blank DVD/CD disc, press the ENT bu ...

Main Menu Functions are selected with the arrow keys. The numbers correspond to the Function listing in the previous section. Copy During the duplication process, data will be written to a blank DVD-R/RW, DVD+R/RW, or CD-R/RW disc loaded in the Duplicator. Before starting the duplication process, please make sure the source DVD/CD is placed in the DVD/CD-ROM drive. Place a blank DVD-R/RW, DVD+R/RW, or CD-R/RW ...

When copying audio CDs, it is highly recommended to copy at a speed of 16x or lower to ensure the best possible quality audio reproduction. Go to “Setup” and then “Burning Speed” to change copy speed before selecting tracks. ...

Main Menu Test This function is a test process that simulates data being written to the DVD/ CD-R/RW disc, without actually burning a disc. When the test process is complete, the DVD-R/RW or CD-R/RW discs will remain blank. For DVD- RW or CD-RW discs that contain data, “Test” will quick erase all old data before simulation. Therefore, never perform “Test” on DVD/CD-RW discs that contain important data ...