Absolare Push-Pull Operation & User’s Manual

Text of Absolare Push-Pull Operation & User’s Manual

ABSOLARE Push-Pull Amplifier User Manual 0.9

Contents 1.  General  Description  ..............................................................................................................  4 2.  Safety  Issues  and  Warnings  ..................................................................................................  4 3.  Unpacking  and  Placement  ....................................................................
ABSOLARE Push-Pull Amplifier User Manual 0.9 1.  General  Description The Absolare Push-Pull Amplifier is a transformer coupled, zero feedback, two chassis monoblock stereo amplifier with an all tube signal path and point-to-point construction. Transformer Balanced (XLR) and Single-ended (RCA) input versions are available. 2.  Safety  Issues  and  Warnings - - Ensure the voltage setting of the unit matches the voltage of the available AC powe
ABSOLARE Push-Pull Amplifier User Manual 0.9 3.  Unpacking  and  Placement The monoblock amplifiers are supplied in separate boxes. After opening the top cover of the box, remove the upper layer of hard foam material. You can then lift the units from the box using the cloth underneath each chassis. Feet can affect the sound quality significantly. Feet should be placed directly under the aluminum base plate, not the MDF/leather plate. There are thre
ABSOLARE Push-Pull Amplifier User Manual 0.9 4.  Installing  the  Tubes There are total of 5 tubes in each monoblock. Placement of tubes is shown below:
ABSOLARE Push-Pull Amplifier User Manual 0.9 845 tubes must be installed in the correct orientation. The small indicator pin on the lower side of the tube base should match the small hole on the right-side of the tube socket, as illustrated in the figure below. CAUTION: Incorrect positioning of 845 may seriously damage the amplifier!
ABSOLARE Push-Pull Amplifier User Manual 0.9 EL34 tubes have a small bump in the center as a key for correct positioning. Align it with the corresponding notch in the tube socket while inserting. 12AT7 / ECC81 tube has one missing pin acting as a correct positioning key. Align missing pin with the missing hole in the tube socket while inserting.
ABSOLARE Push-Pull Amplifier User Manual 0.9 5.  Connecting  the  Cables 5.1.  Power  cables AC power input is via a standard IEC socket. Operating voltage must only be changed by an authorized service agent. The quality of the power cable used will affect the sound quality. 5.2.  Signal  Cables Single-ended version has only one RCA input connector. Balanced version has both RCA and XLR input connectors. The RCA and XLR inputs are connected
ABSOLARE Push-Pull Amplifier User Manual 0.9 6.  Operating  the  Unit 6.1.  General  Operation Before turning on the unit be sure that all tubes are installed and all cables connected correctly. If you have changed 845 tubes you should first minimize the bias settings (by rotating to counter-clockwise) before turning-on the amplifiers and re-adjust the bias settings. Please refer the bias settings section (6.2.1). After turning on, the power i
ABSOLARE Push-Pull Amplifier User Manual 0.9 6.2.1.  845  Bias  Levels You have to adjust left and right 845 tube bias levels separately. Measurement is done via a multimeter at 2V DC (or 2000mV DC) setting. Insert black (-) probe into black socket and red (+) probe into one of the green sockets. You should read a value about 0.45V (450mV) for each tube. If the readings are different, then adjust the bias level via potentiometers near the EL34 tub
ABSOLARE Push-Pull Amplifier User Manual 0.9 6.2.2.  EL34  Bias  Levels There is no separate bias adjustments for EL34 tubes, but the push-pull symmetry is important. With a multimeter at lowest DC volt measurement setting, insert black and red probes into blue sockets. The adjustment point is in between the EL34 sockets. You should try to get 0.0V or near by turning the adjustment pot with a small flat screwdriver. If you cannot cross the zero va
ABSOLARE Push-Pull Amplifier User Manual 0.9 7.  Troubleshooting  and  Maintenance Surface of the unit is dirty. Clean with a slightly damp cloth. No power light. - Check AC line voltage. - Check the main fuse. Power light is on but 845 tube heaters are not glowing. - Tube orientation is wrong, turn-off the immediately and correct the installation. - Tube(s) are defective. Power light is on, tube heaters are glowing, but no sound. - Check the inpu

ABSOLARE USA LLC

40 Pemberton Road, Nashua New Hampshire, 03063 Phone: +212-229-1842 E-mail: [email protected] ABSOLARE SERVICE EUROPE Mozartstraat 157, 1962AL Heemskerk, Netherlands Phone: +31 61 399 3049 E-mail: [email protected] © 2015 ABSOLARE

Absolare Amplifier Owners Instructions: