Lanner FW-7541 Operation & User’s Manual

FW-7541 User's Manual Publication date:2012-08-01 ...

Overview Icon Descriptions The icons are used in the manual to serve as an indication of interest topics or important messages. Below is a description of these icons: NOTE: This check mark indicates that there is a note of interest and is something that you should pay special attention to while using the product. WARNING: This exclamation point indicates that there is a caution or warning and it is something tha ...

LITHIUM BATTERY CAUTION: Risk of Explosion if Battery is replaced by an incorrect type. Dispose of used batteries according to the instructions Operating Safety Electrical equipment generates heat. Ambient air temperature may not be adequate to cool equipment to acceptable operating temperatures without adequate circulation. Be sure that the room in which you choose to operate your system has adequate air circul ...

iii Chapter 1: Introduction 1 System Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Front Panel Features . . . . . . . . ...

iv Appendix C: Programming the LCM 40 Appendix D: Programming LAN Bypass 41 Appendix E: Driver Installation 42 LAN Adapters Driver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 On the Windows OS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Chapter 1: Introduction Thank you for choosing the FW-7541. The FW-7541 is a desktop network communication appliance which is built on Intel® Pineview™ embedded processor, the next- generation in the Intel ® Atom™ family. The FW-7541 is an ideal network system platform. All electronics are protected in a compact sealed rugged case for easy installation in customers’ computer facilities, or it c ...

Package Contents Your package contains the following items: FW-7541 Network Security Platform • Power cable • 1 crossover Ethernet cable (1.8 meters) • 1 straight-through Ethernet cable (1.8 meters) • 1 RJ-45 to DB-9 female console cable • Serial-ATA hard drive cable • 1 tabletop mounting screw pack • 1 hard disk installation screw pack (only supplied with • systems shipped without pre- ...

F1 Console Port By using suitable rollover cable (Cisco console cable), you can connect to a computer terminal for diagnostic or configuration purpose. Terminal Configuration Parameters: 115200 baud, 8 data bits, no parity, 1stop bit, and no flow control. F2 HDD/Status/Power LED HDD: If the LED blinks, it indicates data access activities; otherwise, it remains off. Status: This LED is programmable. ...

Rear Panel Features R1 Reset Switch Use a pointed object to press the reset button for about 3 seconds to reboot the system without turning off the power. R2 Power-on Switch It is a switch to turn on or off the power. R3 AC Power-in socket The system requires a 60W/12V switching power supply with lock. R4 System fan (only on models A and B) Note: Models C and D are fanless; models A and B are with ...

Chapter 2: Hardware Setup Preparing the Hardware Installation To access some components and perform certain service procedures, you must perform the following procedures first. WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment, remove the power cord to remove power from the device. The Power On/Standby button on the back panel does not completely shut off sys ...

Installing the Hard Disk The system can accommodate one Serial-ATA disk (2.5”). Follow these steps to install a hard disk into the FW-7541: Take off the black cap covering the hard disk mounting 1. holes and insert the anti-vibration rubber to the mounting holes. Make sure that the rubber goes through the holes when inserting it. Place hard disk inside the cover and align the corners of 2. the hard ...

Installing 3G SIM Card Installing Wireless 3G Module Align the wireless module’s cutout with the Mini-PCIe 1. slot notch. Insert the wireless module into the connector 2. diagnoally. Push the other end of the wireless module to be 3. tightened with the latch. Unlock the SIM card tray. 1. Align the SIM card and the tray with the cut-off 2. angle. Insert the SIM card into the tray. 3. Close the tra ...

consideration of equipment nameplate ratings should be used when addressing this concern. Reliable Earthing - Reliable earthing of rack- 5. mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).” CAUTION : Rail/rack mounted equipment is not to be used as a shelf or a work spac ...

Chapter 3: Motherboard Information Block Diagram The block diagram depicts the relationships among the interfaces or modules on the motherboard. Please refer to the following figure for your motherboard’s layout design. 1x DDR3 667/800Mhz SO-DIMM X4 DMI Intel 82583V Intel 82574L Intel 82583V Intel 82583V Intel 82583V Intel 82583V 6x PCI-E x1 VGA Up to 4GB MAX 2 x SATA II USB 2.0 Winbond W ...

Motherboard Layout The motherboard layout shows the connectors and jumpers on the board. Refer to the following picture as a reference of the pin assignments and the internal connectors. Ethernet Ports USB2.0 Ports Console Port USB 2 and 3 Connectors Mini PCI-E Connector VGA Interface SO-DIMM Socket SATA 1/2 Con- nectors Serial Port Connector Keyboard and Mouse Connectors SATA Power Connect ...

ATX Power Button (CN2): The power button has a 2-pin connector; the pin definition is as the following: VGA Interface (J1): It is for connecting the VGA interface cable. CompactFlash Connector (CN4): It is for connecting a Compact Flash card to be served as your system's storage. The socket is CF type II and can fit into both bype I and type II cards. Serial-ATA Power Connector (J8): It ...

The controller contains two modes of operation—a legacy mode using I/O space, and an AHCI mode using memory space. Software that uses legacy mode will not have AHCI capabilities. The AHCI ( Advanced Host Controller Interface) is a programming interface which defines transactions between the SATA controller and software and enables advanced performance and usability with SATA. Platforms su ...

Chapter 4: BIOS Settings Updating the BIOS The Basic Input/Output System (BIOS) can be updated using the designated Flash Utility. To obtain the utility, please contact us either through the sales rep or technical support. Note: For the update version of the BIOS image, please visit Lanner’s support page at http://assist.lannerinc.com. Then select support center from the Main Menu and look under t ...

Accessing the BIOS menu You will need to enter the BIOS Setup program to configure the system when you are installing a motherboard or when the system prompts “Run Setup” during start-up. This section explains how to configure your system using this program. Even if you have never enter the BIOS Setup program when you are installing a motherboard, you can change the configuration of your compute ...

The Main Menu The main BIOS setup menu is the first screen that you can navigate. Each main BIOS setup menu option is described in this chapter. The Main BIOS setup menu screen has two main frames. The left frame displays all the options that can be configured. “Grayed-out” options are configured parameters and cannot be modified. On the other hand, Options in blue can be modified. The right fram ...