PowerTec RIF800 Operation & User’s Manual

User Manual Powertec Telecommunications Pty Ltd 14/511 Olsen Ave Southport QLD 4215 Australia Tel: +61 7 5577 0500 Fax: +61 7 5577 0599 Email: [email protected] Web: www.powertec.com.au ...

1. SYSTEM SPECIFICATION.......................................................................…….............3 2. MECHANICAL SPECIFICATION....................................................................…..........3 3. ALARM SPECIFICATION...................................................................................……..4 4. SYSTEM AUTO SHUTDOWN ALGORITHM...............................................................4 5. SYSTEM AUTO LEVEL CONTROL ALGORITHM .....................................................4 6. SYSTEM OPERATION........................................................................................� ...

Down Link(FWD) Frequency Input Power -60dBm ~ -30dBm / 1Tone Output Power +10dBm 2dB/1Tone Max Gain 70dB 2dB Flatness 4dB(P-P) VSWR 1.7(Max) Delay Under 5us ALC @ (-60 ~ -30dBm) 10dBm 2dB/1Tone 10dBm 2dB/1Tone IMD(@2Tone, 7dBm) -45dBc Over -45dBc Over Impedance 50ohm Supply Power DC 9V/3.5A from AC 100~240V Adaptor RF Connector Type SMA Female ALC ON Level Meter ON Internal Repeat system RF/IF 2. Mechanical Specification Characteristic Unit(mm) Remark Size 227 * 158 * 33.5 D * W * H 3. Alarm Specification Characteristic Specification Remark Over Power (Uplink, Downlink) external Input signal over –30 ...

Oscillation detect level At external input signal over -30dBm Re-check Algorithm Time Action 0~1sec Upon detection, check for the status for 1 sec 2~60sec Shutdown 61~62sec Shutdown status clear, check for the status for 1sec 63~122sec Shutdown 123~124sec Shutdown status clear, check for the status for 1 sec After Repeat Program verification available upon request 5. System Auto Level Control Algorithm ALC(Automatic Level Control) operates at 1dB step to maintain the output level of 10dBm when the input signal is from -60dBm to –30dBm.(30dB range) ...

increase signal strength in small and medium sized areas such as offices, shops and basement car parks in the GSM band, with frequencies that are programmable to the specific requirements of each site. It is small, lightweight, and easy to install. Simply plug it in, and the coverage will be immediately extended. The uplink and downlink gain of the repeater can be adjusted by ALC. 10 10dB dBm m Repeat eater ...

2 - Indoor Antenna Cable Link Port : SMA-Female 3 - DC Input Terminal (Jack) 4 - DC Power ON/OFF S/W 5 - Status Display LED : POWER, ALARM, FWD LEVEL 6 - BRACKET ① ① ② ③ ④ ⑥ ⑤ ...

7. System Installation Contents 1. REPEATER 1SET 2. BRACKET 1SET 3. AC/DC ADAPTER 1SET 4. DONOR ANT 1SET(OPTION) 5. SERVICE ANT 1SET(OPTION) 6. DONOR ANT CABLE 1SET(OPTION) 7. SERVICE ANT CABLE 1SET(OPTION) 8. SCREWS Installation Process This is one of the most important process in repeater installation, as how to install the antenna decides performance of this equipment. 1. Decide a place to install the outdoor antenna considering the cable length of the donor antenna. 2. Attach the antenna bracket at the wall. (Refer image A) ...

3. Place the bracket to the repeater. Refer Image B. 4. Check the Receiving Signal by DONOR CABLE and connect to repeater’s DONOR ANT PORT (Input Signal Receive Range –30~-60dBm) 5. Install the service antenna at the appropriate place and connect the cable with the repeater. 6. Connect the adaptor to the repeater and check the POWER LED power on status. ...

the system has been shutdown as external input signal strength is too strong. Please refer the Trouble Shooting below and check the system status.) 8. At normal operation, the LED status indicates as below; ALARM LED OFF/ POWER LED, FWD LEVEL LED ON Operation Instruction -Upon confirmation of electric power (100~240V/AC), insert AC cable to power supply, then using DC cable, insert power cable to DC power input terminal, which is set on the bottom of the equipment LED Configuration - Power : DC Power is normal -Green LED ON - Alarm : FEW,REV over power, When Shut Down- Re ...

1) Check the AC Power. 2) IF AC power is OK, Check the DC Power by checking Power Supply. When Alarm LED (RED) ON 1) Check the Isolation between Donor ANT. and Service ANT. When no LED blinks at FWD LEVEL LED Check the FWD Input Power level whether it is in normal range. 9. Handling Procedures - Please avoid using the other Power Supply besides included ones. - Prohibited to use other frequencies antennas. - Please refrain from installing the equipments reach of children. ...