Rosslare HLX-40 Operation & User’s Manual
Read Online
Read the Rosslare HLX-40 Operation & User’s Manual online using the built-in PDF viewer.
Key Pages of Document
HomeLogiX HLX-40 User Guide Page iii Table of Contents 1. Introduction ..................................................................... 5 2. Operating the HLX-40 ..................................................... 8 2.1 Quick Reference ........................................................................... 8 2.2 About Everyday Operation ........................................................... 8 2.3 Arming Options ........... ...
HomeLogiX HLX-40 User Guide Page iv 9. User Menu Options ....................................................... 28 9.1 Accessing the User Menu ........................................................... 28 9.2 Changing the Master Code ......................................................... 28 9.3 Defining User Codes .................................................................. 29 9.4 Authorization Codes ........................... ...
Page 5 1. Introduction The HomeLogiXTM HLX-40 family of panels by Rosslare is the perfect wireless security system for intrusion protection of the home, or small office providing security monitoring and IVR Voice messaging. Users receive the latest RF technology in a wide selection of advanced wireless sensors and remotes, and benefit from smooth and easy operation of a large number of security and communication opt ...
HomeLogiX HLX-40 User Guide Page 8 2. Operating the HLX-40 This section describes the day to day operation of the system, as well as provides a quick reference for the Arming/Disarming buttons in the system. 2.1 Quick Reference Use the following buttons on the keypad for quick arming the system: AWAY Arms all sensors and detectors for use when there is no one at home/office. HOME Arms all perimeter sensors and detectors as defined by t ...
HomeLogiX HLX-40 User Guide Page 9 2.3.1. Arm Away Arm Away is the full arming of the system, best used when there is no one is at home or in the office. In Away mode, the system enters Alarm mode if there is a zone violation, regardless of perimeter or interior type. To arm the system using AWAY: 1. Verify that the system is ready for arming. 2. Press the AWAY arming key. 3. Enter your user code. 2.3.2. Arm Home Home arming is an armi ...
HomeLogiX HLX-40 User Guide Page 10 2.3.4. Quick Arming Quick arming allows arming the system without code entry. If Quick Arming is enabled (by the Installer during setup), a long press on one of the arming buttons activates Quick Arming. 2.3.5. Instant Arming If Instant Arming mode is enabled (by the Installer during configuration), the system skips the exit delay, cancels the entry delay configured, and initiates the alarm, which in ...
HomeLogiX HLX-40 User Guide Page 11 2.4.1. Entry Delay Entry delay allows the user a grace period for the time it takes to open the door and reach the keypad to disarm the system. If a zone of type Delay is violated while the system is armed (except Instant Arming), the system does not enter Alarm mode during the Entry Delay period setting. If the delay has transpired and the system still has not been disarmed, the system enters Alarm ...
Page 12 3. Technical Specifications Electrical Characteristics External Power Supply 220 VAC/50 Hz, 110 VAC/60 Hz Operating Voltage Range 15 VDC, 800 mA Input Current Standby: 120 mA Max: 500 mA (750 mA w/GSM expansion) Internal Backup Battery 800 mAh for 6 hours standby Auxiliary Power Output 13.8 VDC, 500 mA max Display Two Line, 16 characters, white backlit LCD PGM Open Collector Outputs Two fully pro ...
Page 13 Dimensions HLX-40 HLX-40A HLX-40B Height x Width x Depth 217 x 144 x 48 mm 8.54 x 5.67 x 1.89 in. 217 x 144 x 50 mm 8.54 x 5.67 x 1.97 in. 217 x 144 x 48 mm 8.54 x 5.67 x 1.89 in. Weight 520g 1.15 lbs. 530g 1.17 lbs. 548g 1.21 lbs. In addition, the HLX-40 system complies with the following standards: • CE, FCC, EN 50131-3, EN 50131-6, EN 50130-5, EN 50130-4, EN 60950-1, EN 50131-5-3, Security G ...
Page 14 4. System Overview The main components of the HomeLogiXTM HLX-40 wireless panel are: • HomeLogiXTM HLX-40 Wireless Panel, Page 14 • The LCD Display, Page 15 • The Keypad, Page 17 • Sound Indicators, Page 19 • LED Indicators, Page 20 4.1 HomeLogiXTM HLX-40 Wireless Panel The following figure presents the components of the wireless panel. Figure 4: Components Power Indicator Display Status Indicat ...
Page 15 The table below describes the components in the panel: Menu Use to navigate between menus Power indicator Power LED Green On: system is ON. FLASHING: AC power failure Status indicator Status LED Red On: system armed. Off: system disarmed. Flash: entry and exit delay (according to beep rate) Keypad door Open to access the keypad buttons Local sounder System speaker Microphone Enables recording voice messag ...
Page 16 two seconds. There are several display options as described below: System Status Ready Indicates that the system is ready for arming. Not ready Indicates that the system is not ready and that there are active zones. Press Enter to see which zones are active. If there is more than one active zone, pressing Enter or Menu displays the next open zone. When there are no more active zones, the display returns t ...
Page 17 4.3 The Keypad The keypad is used to program the wireless panel and to arm and disarm the sensors. Figure 5: The Keypad The following table describes the keypad functions: Key Press to Menu Navigate between User and Installer menus, and Normal mode. Navigate to the next menu or the next option within a menu. Enter Accept an entry or selection when in the menu. Displays the panel current status when in sta ...
Page 18 Key Press to DISARM Disarm all armed sensors and detectors. You must enter a user or master code. If the duress code is enabled by the Installer, entering the duress code when disarming sends a duress event to the Central Station and Private Phone. The system is locked out for 90 seconds in the event of 5 failed attempts to disarm the system. QUICK Ignore an entry (escape) or to move one level up in a men ...
Page 19 Key Press to 4 Normal mode only Volume Manually Adjust the system’s volume level. 5 Normal mode only Sound ON/OFF – If enabled by Installer. Manually toggle voice messages, keypad tone, and other sounds on and off (except for trouble beeps, forced arming, enrollment and RF test of wireless devices which is always on). 6 Normal mode only Bypass – If enabled by installer. Enter the last User menu Bypa ...
Page 20 Sound Sounded When Short beep every second An exit/entry delay is activated. (Beep sounded every 0.5 seconds during last 10 seconds of delay. Chime 1 & 2 Two (2) various chime sounds, when feature is activated Chime 3 Vocal announcement of “Zone Name” + Open Aside from the indication sounds, the system also has a voice confirmation of various events. Note: This table does not include actual alarm soun ...
