nLight rES7 Manuals

1 of 3 rES7 Sensor Fixture Embedded Smart Sensor 360° COVERAGE • LOW VOLTAGE • WIRELESS Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitybrands.com © 2021 Acuity Brands Lighting, Inc. All rights reserved. Rev. 04/29/2021 IS-RES7-002 Electrical Specifications Input Ratings 5-60 VDC Maximum Load 0.65 W Dimming Load Sinks <20mA (0-10 VDC LED Drivers/Ballasts) Minimum Load None Class Rating Class 2 Mechanical Mounting Fixture-Mounted Mounting Height Up to 20 ft (6.096m) Connection Type Low Voltage Leads Environmental Warrantied Operating Temperature -4º to 185º F (-20º to 85º C) Standards/ Ratings RoHS, UL 916, UL 924 (optional), FCC / IC / IFETEL SPECIFICATIONS (rES7) READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION IMPORTANT SAFEGUARDS WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED INCLUDING THE FOLLOWING: • DO NOT USE OUTDOORS. • DO NOT MOUNT NEAR GAS OR ELECTRIC HEATERS. • EQUIPMENT SHOULD BE MOUNTED IN LOCATIONS AND AT HEIGHTS WHERE IT WILL NOT READILY BE SUBJECTED TO TAMPERING BY UNAUTHORIZED PERSONNEL. • THE USE OF ACCESSORY EQUIPMENT NOT RECOMMENDED BY THE MANUFACTURER MAY CAUSE AN UNSAFE CONDITION. TITLE 20/24 √ Do not exceed maximum wattage, ratings, or published operation conditions of product. √ Do not overload. √ Follow all manufacturer’s warnings, recommendations and restrictions to ensure proper operation of product. • To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels. • Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions. • Installation and service should be performed by a qualified licensed electrician. • Maintenance should be performed by qualified person(s) familiar with the products’ construction & operation & any hazards involved. Regular maintenance programs recommended. • DO NOT INSTALL DAMAGED PRODUCT! This product has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced. CAUTION: RISK OF PRODUCT DAMAGE √ Electrostatic Discharge (ESD): ESD can damage product(s). Personal grounding equipment should be worn during all installation or servicing of the unit. √ Do not touch individual electrical components, as this can cause ESD and affect product performance. √ Do not stretch or use cable sets that are too short or are of insufficient length. √ Do not tamper with contacts. √ Do not modify the product. √ Do not change or alter internal wiring or installation circuitry. √ Do not use product for anything other than its intended use. WARNING - RISK OF BURN or FIRE CAUTION - RISK OF INJURY √ Wear gloves and safety glasses at all times when installing, servicing or performing maintenance. WARNING - RISK OF ELECTRIC SHOCK √ Disconnect or turn off power before installation or servicing. √ Verify that supply voltage is correct by comparing it with the product information. √ Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements. √ All wiring connections should be capped with UL approved recognized wire connectors. √ All unused connector openings must be capped. C US LISTED WARRANTY 5-year limited warranty. Full warranty terms located at: www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx Note: Specifications subject to change without notice. Actual performance may differ as a result of end-user environment and application. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the radiator shall not be less than 20cm during normal operation. Contains FCC ID: 2ADCB-RMODIT or 2ADCB-RES7CD Contains IC: 6715C-RMODIT or 6715C-RES7CD IFT #: RCPACRM18-1879 or RCPACRE21-0154 Acuity Brands Lighting Inc. RMODIT or RES7CD