Code Soft TP-290XIII Programmer's Manual

[Format] The code sequence, including ASCII, HEX and DECIMAL. [Range] Gives the allowable ranges for the arguments. [Description] Describes the command’s function. [Details] Describes the usage of the command in detail. [Notes] Provides important information on sett ...

2 3、ESC SP n Set right-side character spacing [Format] ASCII ESC SP n Hex 1B 20 n Decimal 27 32 n [Range] 0 ≤ n ≤ 255 [Description] Sets the character spacing for the right side of the character to inches [ n x horizontal motion units]. [Details] § When characters are enlarged n times, the right-side character spacing ...

3 5、ESC $ nL nH Set absolute print position [Format] ASCII ESC $ nL nH Hex 1B 24 nL nH Decimal 27 36 nL nH [Range] 0 ≤ n ≤ 255 [Description] § Sets the distance from the beginning of the line to the position at which subsequent characters are to be printed. § The distance from the beginning of the line to the prin ...

4 the final code. § x specifies the number of dots in the horizontal direction. [Note] § The available range of character is from ASCII <20>H to <7F>H (96 characters). § Consecutive character codes for multiple characters can be defined in one definition. When specifying only one character, specify c1 = c2。 § d is definition dat ...

5 最高位 最低位 D1 d1 d4 d7 ----------------------- d25 d2 d5 ---------------------------- d26 d3 d6 ---------------------------- d27 17点 9点 8、ESC * m nL nH d1... dk Select bit-image mode [Format] ASCII ESC * m nL nH d1...dk Hex 1B 2A m nL nH d1...dk Decimal 27 42 m nL nH d1...dk [Range] m = 0, 1, 32, 33 ...

6 Vertical Horizontal m Mode Dot Density Density Data（k） 0 8 dots Single Density 8 67 DPI 100 DPI nL + nH × 256 1 8 dots Double Density 8 67 DPI 200 DPI nL + nH × 256 32 24 dots Single Density 24 200 DPI 100 DPI ( nL + nH × 256) × 3 33 24 dots Double Density 24 200 DPI 200 DPI ( nL + nH × 256) × 3 [dpi: dot/25.4mm{ ...

7 单密度 打印数据 1点 双密度 Dd1 d2 d3 d4 d5 d6 d7 d8 d9 位图数据 最高位 位图数据 最低位 打印数据 D d1d4 d7 d2 d5 d8 d3 d6 d9 9、ESC – n Turn underline mode on/off [Format] ASCII ESC - n Hex 1B 2D n Decimal 27 45 n [Range] 0 ≤ n ≤2, 48 ≤n ≤ 50 [Description] Turns underline mode ...

8 10、ESC 2 Select default line spacing [Format] ASCII ESC 2 Hex 1B 32 Decimal 27 50 [Description] Selects default (3.75mm, 1/6-inch) line spacing. [Notes] § Default line spacing is absolute in standard mode and page mode. [Reference] ESC 3 11、ESC 3 n Set line spacing [Format] ASCII ESC 3 n Hex 1B 33 n Decimal 27 51 n [Range] 0 ...

9 [Notes] § The DIP switch settings are not checked again. § The data in the receive buffer is not cleared. § Macro defined is reserved. § NV bitmap data is not cleared. 14、ESC D n1...nk NUL Set horizontal tab positions [Format] ASCII ESC D n1... nk NUL Hex 1B 44 n1...nk 00 Decimal 27 68 n1...nk 0 [Range] 1 ≤ n ≤ 255 0 ...