Oce TDS100 Quick Reference Manual

9 The indicators Nr. Indicator Function 1 'Toner' Indicate that the Océ TDS100 has run out of toner. 2 Green light Indicate that the copier is ready. A blinking green light indicates that the copier runs a copy job. 3 Red light Indicate that an error has occurred. 4 'Media jam' ■ Indicate that the original or copy media has jammed. � ...

Oce TDS100 All rights reserved. No part of this work may be reproduced, copied, adapted, or transmitted in any form or by any means without written permission from Océ. Océ-Technologies B.V. makes no representation or warranties with respect to the contents hereof and specifically disclaims any implied ...

Oce TDS100 The components Nr. Component Function 1 On / off switch Turn on and off the Océ TDS100. Note: The on / off switch is not visible in the illustration. 2 Operator panel Set up, start and control the copy jobs. 3 Original feed table Feed the original. 4 Manual feed table Feed the media manually. 5 Roll 1 (drawer) Feed the media automati ...

Oce TDS100 The components 6 The operator panel 8 Make copies 11 Replace media rolls 12 Add toner 13 Clear jams 15 ...

Oce TDS100 11 Make copies How to copy on a roll medium (automatically) How to copy on a cut sheet (manually) Step Action 1 Place the original centrally and face down on the original feed table. The Océ TDS100 moves the original to the back. 2 Make the required settings. 3 Press the green start key. Step Action 1 Place the original centrally and f ...

Oce TDS100 7 Note: Some components may not be available on your Océ TDS100 due to the differences between the configurations. 7 Integrated receiving tray Receive the copies. 8 Top cover Give access to the transparent plate. 9 Fuser cover Give access to the fuser. Note: The fuser is not visible in the illustration. 10 Left cover Give access to the ...

Oce TDS100 The keys Note: Some functions may not be available on your Océ TDS100 due to the differences in the configurations. Nr. Key Function 6 'Media' Select the media type. 7 'Feed' Select the media feed method. 8 Exposure Adjust the exposure. Use the exposure setting to correct the background of the copy. 9 'Strip' Select the edge for the ...

Oce TDS100 15 Clear jams How to remove a jammed original Step Action 1 Open the top cover in case of a fragile original. Pull the top cover towards you and lift the top cover to open it. 2 Pull the original carefully with two hands towards you 3 Check on a media jam also and clear the media jam if necessary ...

Oce TDS100 3 Turn the bottle in the vertical position. 4 Wait until the bottle is empty. Return the bottle into the original position. 5 Turn the bottle anticlockwise to loosen the bottle from the bottle holder. 6 Pull the waste toner bag from its holder. Close the waste toner bag. 7 Slide the new waste toner bag over the holder. 8 Close the le ...

Oce TDS100 Replace media rolls How to replace a media roll Step Action 1 Open the drawer with roll 1 or the door in front of roll 2. 2 Replace the media roll and follow the instructions on the sticker. 3 Use the 'Feed' key to select the roll number of the new roll. 3 Use the 'Media' key to select the media type of the new roll. 4 Use the adjust ...

17 How to remove the media from the fuser unit Caution: The fuser section can be hot. Attention: The jammed media can contain loose toner. Step Action 1 Turn off the Océ TDS100. 2 Loosen the nut at the left back side. Open the left cover. 3 Lift the green handle and open the fuser cover. 4 Remove the jammed media carefully. Note: Make ...

The operator panel 4 2 0 -2 -4 media paper roll 1 trailing synchro film roll 2 leading standard feed manual strip cut toner media jam 6 8 1 2 3 4 5 14 13 10 12 7 9 11 ...